• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2005.11a
• /
• pp.183-184
• /
• 2005

Four different coatings deposited using cold spray process were studied with two different powder agglomerating techniques (spray d교 and evaporated powder) and using $TiO_2$ nano-sized powders with and without a 10wt% addition of ZnO. Characterization was performed by SEM, XRD and roughness test. Also the photocatalytic effect of the coatings was evaluated. Although the change of powder preparation techniques and the addition of ZnO into $TiO_2$ did not show appreciable variations in the surface morphology and Anatase phase transformation, it did show influence on the surface roughness of the coating, the highest roughness being found in the coatings made by spray powder prepared method. Regarding the photocatalytic effect it was observed that the using the spray dry coating and the addition of ZnO are promoter of purification at higher rates.

• Journal of the Korean Society of Safety
• /
• v.21 no.1 s.73
• /
• pp.65-71
• /
• 2006

Flame retardancy and mechanical properties of polyolefinic mixed waste plastics/filler composites were investigated by using inorganic flame retardant(magnesium hydroxide) and PUB(polyurethane block) powder generated from cryogenic insulation process. All composites were obtained by extrusion and after compression molding. The effect of PUB powder on the properties of the composites was studied by tensile and izod impact test, morphology studies and flammability as LOI and UL94 vertical burning test and smoke density. The objective of this work is to obtain good mechanical properties from recycled PP composites with $Mg(OH)_{2}/PUB$ powder as fillers and optimum cost-performance balance, in addition to flame retardant characteristics.

• Journal of Powder Materials
• /
• v.10 no.3
• /
• pp.186-189
• /
• 2003

A chemical vapor condensation (CVC) process using the pyrolysis of metal-organic precursors was applied to produce the nanosized $WO_3$ powders. Morphology and phase changes of the synthesized $WO_3$ powder as a function of CVC parameters were investigated by XRD, BET and TEM. The agglomerated nanosized monoclinic $WO_3$ powders with nearly spherical shape and 10-38 nm in mean diameter could be obtained. Conditions to produce the $WO_3$ nanopowders are presented in this paper.

• Journal of Powder Materials
• /
• v.10 no.3
• /
• pp.157-160
• /
• 2003

Phase contents and elemental composition of ultradispersed powders obtained by the electrical explosion of tin-leadalloy powders are investigated. It is demonstrated that during the explosion and subsequent cooling, surface layers of powder particles are enriched in lead compared to the initial alloy. The thermal stability of powders oxidizing in air is also investigated.

• Journal of Powder Materials
• /
• v.9 no.4
• /
• pp.218-226
• /
• 2002

The purpose of the present study is to investigate the influence of thermal debinding and sintering conditions on the sintering behavior and mechanical properties of PIMed 316L stainless steel. The water atomized powders were mixed with multi-component wax-base binder system, injection molded into flat tensile specimens. Binder was removed by solvent immersion method followed by thermal debinding, which was carried out in air and hydrogen atmospheres. Sintering was done in hydrogen for 1 hour at temperatures ranging from 1000℃ to 1350℃ The weight loss, residual carbon and oxygen contents were monitored at each stage of debinding and sintering processes. Tensile properties of the sintered specimen varied depending on the densification and the characteristics of the grain boundaries, which includes the pore morphology and residual oxides at the boundaries. The sinter density, tensile strength (UTS), and elongation to fracture of the optimized specimen were 95%, 540 MPa, and 53%, respectively.

• Journal of the Korean Ceramic Society
• /
• v.26 no.2
• /
• pp.201-209
• /
• 1989

Fine Si-Al-OH coprecipitate powders were prepared from Si- and Al-alkoxides by the hydrolysis method. $\beta$-Sialon powder was obtained from prepared Si-Al-OH coprecipitate by the simultaneous reduction and nitridation method. The syntehsized Sialon powder was pressureless sintered at 175$0^{\circ}C$ for 90 min in N2 atmosphere. The characterization of the Sialon powder was performed with XRD, BET, SEM, TEM and particle size analysis. The sinterability and mechanical properties of sintered bodies were investigated in terms of relative density, M.O.R., fracture toughness, hardness and the morphology of microstructure. The highest values of their mechanical properties were obtained for the $\beta$-Sialon ceramics at Z=1 and those values are as follows : M.O.R., KIC and HV of $\beta$-Sialon ceramics(Z=1) are 499.1 MPa, 5.9MN/m3/2 and 18.7GPa, respectively.

• Journal of Sensor Science and Technology
• /
• v.14 no.5
• /
• pp.297-301
• /
• 2005

Nanocrystalline SnO and $SnO_{2}$ powder have been prepared by hydrazine method. Sn-Hydrazine complex was formed by the reduction between aqueous $SnCl_{2}$ solution and hydrazine monohydrate. $SnO_{2}$ nano powder was prepared by the decomposition of Sn-Hydrazine complex at $450^{\circ}C$. When NaOH was added to Sn-hydrazine complex, SnO powder with nano-sheet morphology could be prepared. This can be attributed to the role of $OH^{-}$ ion as a reducing agent.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.163-164
• /
• 2006

A QM-ISP-4 Planetary Mill was employed to activate mechanically the mixtures of anatase and corundum at room temperature for different times. The milled powder mixtures were then sintered at $1300^{\circ}C$ for 1 h. The XRD results showed that the milled powder mixtures were completely transformed into $Al_2TiO_5$ after sintering, except the mixtures milled for 5 and 10 hours. The SEM observations showed the typical morphology of rod-like $Al_2TiO_5$ vary in the range: widths from 0.6 to $1.2\;{\mu}m$, and lengths from 3.0 to $6.0\;{\mu}m$. The rod-like $Al_2TiO_5$ formation was attributed to the positive effects caused by the mechanical activation.

• Transactions of Materials Processing
• /
• v.12 no.5
• /
• pp.457-464
• /
• 2003

In the powder compact melting technique, proper precursor fabrication is very important because density distribution after foaming and foamability are determined during precursor fabrication process. The fabrication of the precursor has to be performed very carefully because any residual porosity or other defects will lead to poor results in further processing. In order to evaluate the effect of the compaction parameters on the kinetics of the foaming process, a series of experiments were performed. In this study, aluminium foams with a closed cell structure were fabricated by using both the powder compact method and the induction heating process. A proper induction coil was designed to obtain a uniform temperature distribution over the entire cross sectional area of precursor. To establish the foamable precursor fabrication conditions, effects of process parameters such as the titanium hydride content (0.3∼1.5 wt.%), pressing pressure of the foamable precursor (50∼150kN) on the pore morphology were investigated.

• Journal of Powder Materials
• /
• v.12 no.3
• /
• pp.186-191
• /
• 2005

A formation of aluminum hydroxide by hydrolysis of nano and micro aluminum powder has been studied. The nano aluminum powder of 80 to 100 nm in diameter was fabricated by a pulsed wire evaporation (PWE) method. The micro powder was commercial product with more than $10\;{\mu}m$ in diameter. The hydroxide type and morphology depending on size of the aluminum powder were examined by several analyses such as XRD, TEM, and BET. The hydrolysis procedure of micro aluminum powder was different from that of nano aluminum powder. The nano aluminum powder after immersing in the water was transformed rapidly to a nano fibrous boehmite, accompanying with a remarkable temperature increase, and then further transformed slowly to a stable bayerite. However, the micro powder was changed to the stable bayerite slowly and directly. The formation of fibrous aluminum hydroxide from nano aluminum powder might be due to the fine cracks which were formed by hydrogen gas pressure on the surface hydroxide layer during hydrolysis. The nano powder with large specific surface area and small size reacted more actively and faster than the micro powder, and transformed to meta-stable hydroxide in relatively short reaction time. Therefore, the formation of fibrous boehmite is special characteristic of hydrolysis of nano aluminum powder.