• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.145-149
• /
• 2004

It is necessary for managing a perfect process for degasing aluminum molten metal according to the increase of a grade of aluminum and its alloy products. There are some methods that have been used to manage a degasing process in recent years, such as an injection method that uses aluminum molten metal powder and chemicals supplier and input method that supplies argon and nitrogen, or chlorine gas by using a gas blow-tube. However, these methods show some problems, and it shows that it is a difficult process to handle. pollution due to the producing a lot of toxic gases like chlorine and fluoride gas. irregular effects, and lowering work efficiency due to the excessive processing time. The problems that are the most fatal are the producing a lot of sludge due to the reaction of aluminum molten metal with chemicals. loss of metals, and decreasing the life of refractory materials. In order to solve these problems. this paper develops a technology that is related to aluminum continuous casting molten metal and monolithic degasing apparatus. A degasing apparatus developed in this study improved the exist ing methods and prevented environmental pollution wi th smokeless. odor less, and harmlessness by using a new method that applies argon and nitrogen gas in which the methods used in the West and Japan are eliminated. The developed method can significantly reduce product faults that are caused by the production of gas and oxidation because it uses a preprocessed molten metal with chemicals. In addition. the amount of the produced sludge can also be reduced by 60-80% maximum compared with the existing methods. Then. it makes it possible to minimize the loss of metals. Moreover. the molten metal processing and settling time is also shortened by comparing it with the existing methods that are applied by using chemicals. In addition, it does much to improve the workers' health, safety and environment because there is no pollution. The improvement of productivity and prevent ion effects of disaster from the results of the development can be summarized as follows. It will contribute to the process rationalization because it does not have any unnecessary processes that the molten metal will be moved to an agitator by using a ladle and returned to process for degasing like the existing process due to the monolithic configuration. There are no floating impurities due to the oxidation caused by the contact with the air as same as the existing process. In addition. it can protect the blending of precipitation impurities. Because it has a monolithic configuration. it can avoid the use of additional energy to compensate the temperature decreasing about 60t that is caused by the moving of molten metal. It is not necessary to invest an extra facilities in order to discharge the gas generated from a degasing process by using an agitator. The working environment can be improved by the hospitable air in the factory because the molten metal is almost not exposed in the interior of the area.

• 콘크리트학회논문집
• /
• 제23권6호
• /
• pp.773-780
• /
• 2011

이 연구는 초대형 매스 구조물인 지하식 LNG 저장탱크의 바닥슬래브 및 측벽에 타설되는 매스 콘크리트의 재료특성, 배합조건, 양생조건 및 콘크리트의 타설시기와 초기온도, 외기온 등을 고려한 온도응력 해석 결과를 기술하였다. 해석 결과를 토대로 유해한 균열의 발생 가능성을 예측하고, 이를 방지하기 위한 방안을 제시하였다. 이 연구에서는 콘크리트의 단열온도 상승시험을 통하여 수화열 관리에 유리하다고 평가된 2종류(벨라이트 시멘트+석회석 미분말)의 최적배합조건을 선정하였다. 온도응력 해석의 결과에 따르면, 바닥슬래브 2단을 제외한 대부분의 분할타설 블록에서 관통균열지수가 1.2이상을 만족하였다. 바닥슬래브 2단의 경우 균열방지 대책으로 선행냉각 방안을 제시하였으며, 콘크리트의 초기온도를 $25^{\circ}C$ 범위에서 관리할 경우에는 대부분의 타설블록에서 관통균열지수 1.2이상을 만족하는 것으로 나타났다. 또한, 바닥슬래브의 경우, 표면균열지수가 1.2이상이기 때문에 양생조건을 준수하면 표면균열을 제어할 수 있으며, 측벽의 경우에도 표면균열지수가 1.0이상을 만족하기 때문에 균열의 수 및 폭을 제어할 수 있는 것으로 나타났다.

• Corrosion Science and Technology
• /
• 제8권5호
• /
• pp.171-176
• /
• 2009

The chloride threshold level (CTL) in mixed concrete containing, ordinary Portland cement (OPC), pulverized fuel ash (PFA) ground granulated blast furnace slag (GGBS), and silica fume (SF) is important for study on corrosion of reinforced concrete structures. The CTL is defined as a critical content of chloride at the steel depth of the steel which causes the breakdown of the passive film. The criterion of the CTL represented by total chloride content has been used due to convenience and practicality. In order to demonstrate a relationship between the CTL by total chloride content and the CTL by free chloride content, corrosion test and chloride binding capacity test were carried out. In corrosion test, Mortar specimens were cast using OPC, PFA, GGBS and SF, chlorides were admixed ranging 0.0, 0.2, 0.4, 0.8, 1.0, 1.5, 2.0, 2.5 and 3.0% by weight of binder. All specimens were cured 28 days, and then the corrosion rate was measured by the Tafel's extrapolation method. In chloride binding capacity, paste specimens were casting using OPC, PFA, GGBS and SF, chlorides were admixed ranging 0.1, 0.2, 0.3, 0.5, 1.0, 1.5, 2.0, 2.5 and 3.0% by weight of binders. At 28days, solution mixed with the powder of ground specimens was used to measure binding capacity. All specimens of both experiments were wrapped in polythene film to avoid leaching out of chloride and hydroxyl ions. As a result, the CTL by total chloride content ranged from 0.36-1.44% by weight of binders and the CTL by free chloride content ranged from 0.14-0.96%. Accordingly, the difference was ranging, from 0.22 to 0.48% by weight of binder. The order of difference for binder is OPC > 10% SF > 30% PFA > 60% GGBS.

• 한국결정성장학회지
• /
• 제28권5호
• /
• pp.217-221
• /
• 2018

Selective laser melting(SLM)은 적층 제조 방법 중 하나로서, 분말을 선택적으로 용융하여 기능적이고, 복잡한 형상을 즉각적으로 제작 가능하다는 장점이 있다. Ti-6Al-4V 합금의 경우 높은 융점과 산화문제로 인하여 SLM 공정도입에 어려움을 겪고 있다. 본 연구에서는 SLM 장비를 사용하여 Ti-6Al-4V 파트를 성공적으로 적층하였으며 스캔속도, 레이저 파워의 변수를 조절하여 적층 가능 조건을 도출하였다. 또한 적층 된 Ti-6Al-4V 파트의 형상 정밀도, 면밀도 및 기계적특성 평가를 통하여 일반적으로 사용되는 공정조건(스캔 속도 200~700 mm/s)으로 제작된 제작품 물성치와 비교를 통해 Ti-6Al-4V 합금의 고속 적층 영역에서의 최적 공정을 확립하였다.

• 한국세라믹학회지
• /
• 제43권7호
• /
• pp.421-426
• /
• 2006

[ $(BaSr)TiO_3$ ] thick films were prepared by tape casting method, using $BaTiO_3\;and\;SrTiO_3$ powder slurry in order to investigate dielectric properties i.e. dielectric constant, ${\varepsilon}_r$, Curie temperature, $T_c$. Grain growth within $(BaSr)TiO_3$ thick films was observed with increasing weight ratio of $BaTiO_3$. This observation can be explained by phenomena of substitution of $Sr^{2+}$ ion for $Bi^{2+}$ ion in the $BaTiO_3$ system. Also, the Curie temperature in $(BaSr)TiO_3$ thick films was shifted to lower temperature range with increasing $ SrTiO_3$. Furthermore, Curie temperature having maximum dielectric constant was in the range of $-40^{\circ}C\;to\;30^{\circ}C$, and hence sharper phase transformation occurred at Curie temperature. There occurred decrease in tunability and k-factor of $(Ba_{0.6}Sr_{0.4})TiO_3$ calculated from the dielectric constant, ${\varepsilon}_r$ above Curie temperature. In addition, above the $60^{\circ}C$, phase fixation was observed. This means that internal stress relief occurred with increasing $90^{\circ}$ domains.

• 한국전기전자재료학회논문지
• /
• 제30권11호
• /
• pp.683-687
• /
• 2017

We investigated the structure of an ultra-thin insulating board with low thermal conductivity along z-axis, which was based on the idea of void layers created during the glass infiltration process for the zero-shrinkage low-temperature co-fired ceramic (LTCC) technology. An alumina and four glass powders were chosen and prepared as green sheets by the tape casting method. After comparison of the four glass powders, bismuth glass was selected for the experiment. Since there is no notable reactivity between alumina and bismuth glass, alumina was selected as the supporting additive in glass layers. With 2.5 vol% of alumina powder, glass green sheets were prepared and stacked alternately with alumina green sheet to form the 'alumina/glass (including alumina additive)/alumina' structure. The stacked green sheets were sintered into an insulating substrate. Scanning electron microscopy revealed that the additive alumina formed supporting bridges in void layers. The depth and number of the stacking layers were varied to examine the insulating property. The lowest thermal conductivity obtained was 0.23 W/mK with a $500-{\mu}m-thick$ substrate.

• Journal of Electrical Engineering and Technology
• /
• 제6권2호
• /
• pp.263-269
• /
• 2011

In this study, the compositions for the microwave dielectric materials were investigated to obtain the improved dielectric properties, the high temperature stability, and the sintering temperature of less than $900^{\circ}C$, which was necessary for cofiring with the internal conductor of silver. In addition, the dielectric sheets were prepared by the tape casting technique, after which the sheets were laminated and sintered. In this process, the optimum ratio of powder and binder, laminating pressure, temperature, and possibility for cofiring with the internal conductor were studied. Finally, multilayer chip treplexer filter for the 800-2,000 MHz range were fabricated, and the frequency characteristics of the triplexer filter were investigated. When the $0.6TiTe_3O_8-0.4MgTiO_3+3wt%SnO+7wt%H_3BO_3$ ceramics were sintered at $820^{\circ}C$ for 0.3 hours, the microwave dielectric properties of the dielectric constant of 29.91, quality factor of 33,000 GHz, and temperature coefficient of resonant frequency of -2.76 ppm/$^{\circ}C$ were obtained. Using the Advanced Design System (ADS) and High Frequency Structure Simulator (HFSS), the multilayer chip triplexer filter acting at the range of 800-2,000 MHz were simulated and manufactured. The manufactured triplexer filter had the excellent frequency properties in the CDAM800, GPS and PCS frequency regions, respectively.

• The Journal of Advanced Prosthodontics
• /
• 제6권4호
• /
• pp.266-271
• /
• 2014

PURPOSE. The purpose of this study was to compare the fracture strength of the metal and the bond strength in metal-ceramic restorations produced by selective laser sintering (SLS) and by conventional casting (CAST). MATERIALS AND METHODS. Non-precious alloy (StarLoy C, DeguDent, Hanau, Germany) was used in CAST group and metal powder (SP2, EOS GmbH, Munich, Germany) in SLS group. Metal specimens in the form of sheets ($25.0{\times}3.0{\times}0.5mm$) were produced in accordance with ISO 9693:1999 standards (n=30). To measure the bond strength, ceramic was fired on a metal specimen and then three-point bending test was performed. In addition, the metal fracture strength was measured by continuing the application of the load. The values were statistically analyzed by performing independent t-tests (${\alpha}=.05$). RESULTS. The mean bond strength of the SLS group (50.60 MPa) was higher than that of the CAST group (46.29 MPa), but there was no statistically significant difference. The metal fracture strength of the SLS group (1087.2 MPa) was lower than that of the CAST group (2399.1 MPa), and this difference was statistically significant. CONCLUSION. In conclusion the balling phenomenon and the gap formation of the SLS process may increase the metal-ceramic bond strength.

• 한국주조공학회지
• /
• 제21권4호
• /
• pp.253-259
• /
• 2001

There are many methods to produce metal foams, which can be classified into three groups according to the state of the starting metal i.e. liquid or powder or solid. Three types of defects such as cell closing, cell deformation or breakdown and cell misrun are thought to be occurred when we make the open cell aluminum foams by precision casting. Filling ability of the mold slurry between preform is related with cell closing, mold collapsibility is related with cell deformation or breakdown, mold temperature and pouring pressure are related with cell misrun. These factors can be evaluated by measuring slurry fluidity, burnout strength and permeability of the mold. Properties of the plaster mold were evaluated to find optimum mold conditions for high quality open cell aluminum foam in this study. Permeability was almost zero independent of burnout conditions, however, crack initiation was found on the surface of all specimens one or two minutes after taking out from the furnace. Crack has grown and disappeared with time. This crack may facilitate the mold filling when molten metal is poured, because of the improved mold permeability. It was considered that crack initiation and disappearance was closely related with temperature difference between the surface and inner part. Knocking-out the mold is a difficult problem due to the small cell size, because continuous mesh structure of the metal foam is not strong. It is not easy to remove molding material after pouring. We can expect that water quenching can facilitate the knocking-out the mold after solidification without damaging cell structures. Collapsed particles after water quenching became bigger with the increase in time.

• 구강회복응용과학지
• /
• 제32권3호
• /
• pp.246-254
• /
• 2016

Direct metal laser sintering (DMLS) 방식은 3D 프린팅 중 한 방식으로, 재료를 쌓아가면서 레이저를 이용하여 선택적으로 sintering하는 방식이다. 이는 주조 방식에서 문제되는 결손과 뒤틀림을 방지할 수 있으며 절삭 가공 방식으로 제작하기 어려운 복잡한 구조물을 제작할 수 있다. 본 증례들은 DMLS 방식을 이용하여 지대치 간 길이가 긴 고정성 보철물, 포스트 등 다양한 고정성 보철물을 제작하여 수복하였고, 주기적인 관찰 결과 심미적, 기능적으로 만족할만한 결과를 얻었기에 이를 보고하는 바이다.