• Journal of Powder Materials
• /
• v.25 no.1
• /
• pp.19-24
• /
• 2018

Cu-Fe alloys (CFAs) are much anticipated for use in electrical contacts, magnetic recorders, and sensors. The low cost of Fe has inspired the investigation of these alloys as possible replacements for high-cost Cu-Nb and Cu-Ag alloys. Here, alloys of Cu and Fe having compositions of $Cu_{100-x}Fe_x$ (x = 10, 30, and 50 wt.%) are prepared by gas atomization and characterized microstructurally and structurally based on composition and powder size with scanning electron microscopy (SEM) and X-ray diffraction (XRD). Grain sizes and Fe-rich particle sizes are measured and relationships among composition, powder size, and grain size are established. Same-sized powders of different compositions yield different microstructures, as do differently sized powders of equal composition. No atomic-level alloying is observed in the CFAs under the experimental conditions.

• Journal of Powder Materials
• /
• v.2 no.3
• /
• pp.201-207
• /
• 1995

In general, the characteristics of plasma spray coating are strongly dependent on process conditions. In this paper, Mo and Co alloy coating layers were made by plasma spraying with different spray parameters and characterized using X-ray diffraction, scanning electron microscopy(SEM), hardnass test, and wear test. It was found that the coating characteristics were mainly affected by phase composition of the powder, spray distance, arc current, and gas flow rate.

• Journal of Powder Materials
• /
• v.4 no.3
• /
• pp.205-213
• /
• 1997

Mechanical alloying of $Ni_3Al$ and $Y_2O_3$ added ODS $Ni_3Al$ from elemental powders was investigated by the X-ray diffraction, differential scanning calorimeter, transmission electron microscopy and optical microscopy. The steady states of $Ni_3Al$ and ODS $Ni_3Al$ powders were reached after mechanical alloying with the condition of the ball-to-powder input ratio of 20:1 for 20 hours and 10 hours, respectively. The addition of nano-sized $Y_2O_3$ particles enhanced cold working and fracture, and subsequently accelerated MA of $Ni_3Al$ powders. DSC results of MAed $Ni_3Al$ powders showed four exothermic peaks at 14$0^{\circ}C$, 234$^{\circ}C$, 337$^{\circ}C$ and 385$^{\circ}C$. From the high temperature X-ray diffraction analysis, it was concluded that the peaks were resulted from the recovery solution of unalloyed Al in Ni, the formation of intermediate phase NiAl, and $LI_2$ ordering of MAed $Ni_3Al$ powders.

• Journal of Pharmaceutical Investigation
• /
• v.27 no.3
• /
• pp.233-239
• /
• 1997

Glibenclamide is a second generation sulfonylurea that is orally active as a hypoglycemic drug. It exists as a crystalline powder which is sparingly soluble in water. It was investigated that the potential of glibenclamide to exhibit polymorphism. Three polymorphic modifications (form 1, form 2 and form 3) and three pseudopolymorphic modifications (form 4, form 5 and form 6) were obtained by crystallization from different organic solvents. The isolated crystal forms were characterized by differential scanning calorimetry(DSC), thermogravimetric analysis(TGA) and X-ray crystallography powder diffraction studies. Form 1 was the most stable and melt at $175.4^{\circ}C$. Form 2 was metastable and melt at $151.0^{\circ}C$. Form 3 was a new polymorphic modification because it was different from form 1 and form 2 in X-ray crystallography powder diffraction data. Form 4 was a 1 : 7(toluene : glibenclamide) toluene solvate; form 5 was a 1 : 5(toluene : glibenclamide) toluene solvate; form 6 was a 3 : 8(pentanol : glibenclamide) pentanol solvate. All forms were stable in 3-month storage under 0% or 100% humidity condition. The dissolution rate of form 4 was highest; those of form 2, form 3, form 1, form 5 and form 6 followed.

• Korean Journal of Materials Research
• /
• v.11 no.8
• /
• pp.661-665
• /
• 2001

The mechanical alloying (MA) effect in $\sigma$-VFe intermetallic compound was studied by neutron and X-ray diffraction. The structure of MA $\sigma$-VFe powders were characterized by the X- ray diffraction with Cu- $K\alpha$ radiation and neutron diffraction with monochromatic neutrons of $1.835\AA$ using a high resolution powder diffractometer (HRPD). Mechanical alloying of $\sigma$-VFe compound gives rise to a dramatic structural change. After 60 hours of MA, the Fe-Fe distribution of the $\sigma$- phase VFe tetragonal structure with 30 atoms in a unit cell is found to change into that of the $\sigma$-(V,Fe) solid solution with bcc structure, which is a stable phase at elevated temperature above $1200^{\circ}C$. A comparison of X-ray diffraction data for the $\alpha$-phase has been also made with the corresponding neutron diffraction data. The (101) and (111) diffraction peaks of the $\sigma$-phase was clearly observed only in neutron diffraction pattern, which is believed to be a characteristic feature due to the chemical atomic ordering of $\sigma$- VFe phase.

• Journal of the Mineralogical Society of Korea
• /
• v.12 no.1
• /
• pp.1-10
• /
• 1999

Talc (Mg3Si4O10(OH)2), one of the sheet silicate minerals, which is the hydrothermal alteration product of serpentinite at Cheongarm mine was prepared for the high pressure compressibility studies. Energy dispersive X-ray diffraction experiment was carried out using the Synchrotron Radiation with the Mao-Bell type diamond anvil cell at room temperature. Polycrystalline talc was mixed with MgO powder for pressure sensor as well as pressure medium in the sample chamber. High pressure runs were performed at pressures up to 35.2 GPa. Talc shows no phase transition within the present high pressure region. Bulk modulus of this talc was determined by the Birch-Murnaghan equation of state to be 78 GPa assuming its first pressure derivative Ko' of 4.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1939-1943
• /
• 2003

The precise structural analysis of $SnO_{2}$ thin film, which was prepared by PECVD and thickness 2400 ${\AA}$, was tried to do the structural refinement using X -ray diffraction data. The observed diffraction patterns of $SnO_{2}$ thin film had the strongly preferred orientation effect. WIMV method was used to correct the preferred orientation effect. The final weighted R-factor, $R_{WD}$ was 7.92 %. The lattice parameters, a = b == 4.7366(1) ${\AA}$ and c = 3.1937(1) ${\AA}$, were almost in accordance with ones of $SnO_{2}$ powder.

• Korean Journal of Materials Research
• /
• v.33 no.6
• /
• pp.242-250
• /
• 2023

Titanium, which has excellent strength and toughness characteristics, is increasingly used in the aerospace field. Among the titanium alloys used for body parts, more than 80 % are Ti-6Al-4V alloys with a tensile strength of 931 MPa. The spark plasma sintering (SPS) method is used for solidification molding of powder manufactured by the mechanical milling (MM) method, by sintering at low temperature for a short time. This sintering method avoids coarsening of the fine crystal grains or dispersed particles of the MM powder. To improve the mechanical properties of pure titanium without adding alloying elements, stearic acid was added to pure titanium powder as a process control agent (PCA), and MM treatment was performed. The properties of the MM powder and SPS material produced by solidifying the powder were investigated by hardness measurement, X-ray diffraction, density measurement and structure observation. The processing deformation of the pure titanium powder depends on the amount of stearic acid added and the MM treatment time. TiN was also generated in powder treated by MM 8 h with 0.50 g of added stearic acid, and the hardness of the powder was higher than that of Ti-6Al-4V alloy when treated with MM for 8 h. When the MM-treated powder was solidified in the SPS equipment, TiC was formed by the solid phase reaction. The SPS material prepared as a powder treated with MM 8 h by adding 0.50 g of stearic acid also formed TiN and exhibited the highest hardness of Hv1253.

• Korean Journal of Crystallography
• /
• v.9 no.1
• /
• pp.15-20
• /
• 1998

Single crystals of lithium heptaborate, Li3B7O12(M=288.49), have been grown and their structure was determined by the x-ray powder diffraction and the single crystal diffraction technique. It is found that the borate anion consists of two(B3O7)3- and (B3O8)5- groups a unit cell. The space group was determined to be P-1(Ci1) with a=6.500(3) Å, b=7.839(2) Å, c=8.512(1) Å, α=92.07(2)˚, β=104.97(2)˚, γ=99.35(3)˚, V=412.0(2) Å3, Z=2 Dx=2.32 g cm-3, MoKα, λ=0.71069 Å, μ=2.15cm-1, T=293K. The structure was refined to R=0.0339 and wR=0.0882 for 2296 unique reflections by the single crystal diffraction. By the x-ray powder diffraction, we could obtain the similar results.

• Journal of Powder Materials
• /
• v.11 no.4
• /
• pp.328-332
• /
• 2004

Fe nanopowders were successfully synthesized by plasma arc discharge (PAD) process using Fe rod. The influence of chamber pressure on the microstructure was investigated by means of X-ray Diffraction (XRD), Field Emission Scanning Electron Microscope (FE-SEM), Transmission Electron Microscopy (TEM) and X-ray Photoelectron Spectroscopy (XPS). The prepared particles had nearly spherical shapes and consisted of metallic cores (a-Fe) and oxide shells (Fe$_{3}$O$_{4}$), The powder size increased with increasing chamber pressure due to the higher dissolution and ejection rate of H$_2$ and gas density in the molten metal.