홍성 홍주읍성 성벽의 보존상태 및 축성유형과 안정성 고찰 (Conservation Status, Construction Type and Stability Considerations for Fortress Wall in Hongjuupseong (Town Wall) of Hongseong, Korea)
-
- 헤리티지:역사와 과학
- /
- 제51권3호
- /
- pp.4-31
- /
- 2018
홍주읍성의 초축 연대는 명확히 알 수 없으나 문종 1년 축조 이후 수십 차례에 걸친 보수와 정비를 거쳤으며, 일제강점기에 일부 성벽이 훼철되면서 오늘날의 형태를 갖게 되었다. 홍성은 지구조적으로 지진의 발생 가능성이 높은 지역이다. 역사지진 기록이 남아 있으며, 1978년과 1979년에 각각 규모 5.0과 4.0의 지진이 발생하여 성벽 일부가 붕괴된 바가 있다. 2010년에는 집중강우에 의해 성벽이 붕괴되기도 하였다. 홍주읍성 성벽은 구간에 따라 다양한 구성암종, 치석형태, 축조방식, 채움재료 등이 적용되었다. 또한 보수과정에서 기존의 성벽을 훼철하지 않고 재사용 가능한 부분을 그대로 사용하여 시대에 따른 특성이 성벽에 수직적으로 반영되어 나타난다. 따라서 홍주읍성의 유형분류는 성벽의 수직적 분포를 기준으로 나누었으며, 축성유형의 수직적 개수에 따라 유형 I, 유형 II, 유형 III으로 구분하였다. 성벽에 사용된 암석은 주로 조립질화강암이나 성벽유형에 따라 암종의 차이가 명확하다. 성벽 하부는 자연석 내지 할석을 사용하여 다양한 암종이 혼재되어 나타나나, 중앙부의 치석한 암석은 대부분 조립질 화강암이다. 보수석재는 담홍색화강암이나 수구지와 조양문의 구성 암종은 성벽과 상이하다. 홍주읍성의 대표적인 손상유형은 배부름, 성돌의 돌출, 기초부 성돌의 유실, 부재의 이격, 균열 및 단열, 기초불안정 및 구조적 변형이다. 성벽에 발생하는 거동의 양과 방향을 확인하기 위해 수동 간이계측 및 광파측정을 수행하였다. 수동계측 결과, 성벽의 구조적 변형이 진행되는 구간을 분류할 수 있다. 광파측정 자료와 비교한 결과, 두 모니터링 방법은 상호 상관관계가 있는 것으로 나타났다. 따라서 장기적인 보존관리 방안으로 두 계측방법은 상호 보완적으로 활용할 수 있으며, 홍주읍성의 안정화를 위해 계측시스템은 유지, 관리 및 개선되어야 할 것이다. 남문지 일대의 계측결과를 종합할 때, 붕괴된 성벽 또한 강우에 의한 거동변화가 지속적으로 진행되었을 것이다. 오랜 기간 변위가 누적된 상태에서 집중강우에 의해 발생한 이상거동에 따라 임계점을 초과하여 붕괴에 이르렀을 개연성이 충분하다. 홍주읍성 성벽의 효율적 관리를 위해 연구결과를 토대로 0등급부터 5등급까지 총 6단계의 관리등급을 제안하였다. 이 관리등급을 적용한 결과, 1등급 501.9m (61.10%), 2등급 29.5m (3.77%), 3등급 10.4m (1.33%), 4등급 241.2m (30.80%)로 나타났다. 4등급 구간은 홍화문 서쪽과 치성의 동쪽에 밀집된 양상으로 나타나며, 상시 모니터링 수행을 통해 위험상황에 대비해야 한다. 6단계로 분류한 관리등급은 전체적인 안정성 검토를 통해 수리와 보수가 수행된다면 다시 0등급으로 회귀하는 윤회적 시스템이다. 이를 위해서는 주기적인 정밀 모니터링을 통한 관리등급의 평가가 필요하다.
The objective of this research is to test the feasibility of developing a statewide truck traffic forecasting methodology for Wisconsin by using Origin-Destination surveys, traffic counts, classification counts, and other data that are routinely collected by the Wisconsin Department of Transportation (WisDOT). Development of a feasible model will permit estimation of future truck traffic for every major link in the network. This will provide the basis for improved estimation of future pavement deterioration. Pavement damage rises exponentially as axle weight increases, and trucks are responsible for most of the traffic-induced damage to pavement. Consequently, forecasts of truck traffic are critical to pavement management systems. The pavement Management Decision Supporting System (PMDSS) prepared by WisDOT in May 1990 combines pavement inventory and performance data with a knowledge base consisting of rules for evaluation, problem identification and rehabilitation recommendation. Without a r.easonable truck traffic forecasting methodology, PMDSS is not able to project pavement performance trends in order to make assessment and recommendations in the future years. However, none of WisDOT's existing forecasting methodologies has been designed specifically for predicting truck movements on a statewide highway network. For this research, the Origin-Destination survey data avaiiable from WisDOT, including two stateline areas, one county, and five cities, are analyzed and the zone-to'||'&'||'not;zone truck trip tables are developed. The resulting Origin-Destination Trip Length Frequency (00 TLF) distributions by trip type are applied to the Gravity Model (GM) for comparison with comparable TLFs from the GM. The gravity model is calibrated to obtain friction factor curves for the three trip types, Internal-Internal (I-I), Internal-External (I-E), and External-External (E-E). ~oth "macro-scale" calibration and "micro-scale" calibration are performed. The comparison of the statewide GM TLF with the 00 TLF for the macro-scale calibration does not provide suitable results because the available 00 survey data do not represent an unbiased sample of statewide truck trips. For the "micro-scale" calibration, "partial" GM trip tables that correspond to the 00 survey trip tables are extracted from the full statewide GM trip table. These "partial" GM trip tables are then merged and a partial GM TLF is created. The GM friction factor curves are adjusted until the partial GM TLF matches the 00 TLF. Three friction factor curves, one for each trip type, resulting from the micro-scale calibration produce a reasonable GM truck trip model. A key methodological issue for GM. calibration involves the use of multiple friction factor curves versus a single friction factor curve for each trip type in order to estimate truck trips with reasonable accuracy. A single friction factor curve for each of the three trip types was found to reproduce the 00 TLFs from the calibration data base. Given the very limited trip generation data available for this research, additional refinement of the gravity model using multiple mction factor curves for each trip type was not warranted. In the traditional urban transportation planning studies, the zonal trip productions and attractions and region-wide OD TLFs are available. However, for this research, the information available for the development .of the GM model is limited to Ground Counts (GC) and a limited set ofOD TLFs. The GM is calibrated using the limited OD data, but the OD data are not adequate to obtain good estimates of truck trip productions and attractions .. Consequently, zonal productions and attractions are estimated using zonal population as a first approximation. Then, Selected Link based (SELINK) analyses are used to adjust the productions and attractions and possibly recalibrate the GM. The SELINK adjustment process involves identifying the origins and destinations of all truck trips that are assigned to a specified "selected link" as the result of a standard traffic assignment. A link adjustment factor is computed as the ratio of the actual volume for the link (ground count) to the total assigned volume. This link adjustment factor is then applied to all of the origin and destination zones of the trips using that "selected link". Selected link based analyses are conducted by using both 16 selected links and 32 selected links. The result of SELINK analysis by u~ing 32 selected links provides the least %RMSE in the screenline volume analysis. In addition, the stability of the GM truck estimating model is preserved by using 32 selected links with three SELINK adjustments, that is, the GM remains calibrated despite substantial changes in the input productions and attractions. The coverage of zones provided by 32 selected links is satisfactory. Increasing the number of repetitions beyond four is not reasonable because the stability of GM model in reproducing the OD TLF reaches its limits. The total volume of truck traffic captured by 32 selected links is 107% of total trip productions. But more importantly, ~ELINK adjustment factors for all of the zones can be computed. Evaluation of the travel demand model resulting from the SELINK adjustments is conducted by using screenline volume analysis, functional class and route specific volume analysis, area specific volume analysis, production and attraction analysis, and Vehicle Miles of Travel (VMT) analysis. Screenline volume analysis by using four screenlines with 28 check points are used for evaluation of the adequacy of the overall model. The total trucks crossing the screenlines are compared to the ground count totals. L V/GC ratios of 0.958 by using 32 selected links and 1.001 by using 16 selected links are obtained. The %RM:SE for the four screenlines is inversely proportional to the average ground count totals by screenline .. The magnitude of %RM:SE for the four screenlines resulting from the fourth and last GM run by using 32 and 16 selected links is 22% and 31 % respectively. These results are similar to the overall %RMSE achieved for the 32 and 16 selected links themselves of 19% and 33% respectively. This implies that the SELINICanalysis results are reasonable for all sections of the state.Functional class and route specific volume analysis is possible by using the available 154 classification count check points. The truck traffic crossing the Interstate highways (ISH) with 37 check points, the US highways (USH) with 50 check points, and the State highways (STH) with 67 check points is compared to the actual ground count totals. The magnitude of the overall link volume to ground count ratio by route does not provide any specific pattern of over or underestimate. However, the %R11SE for the ISH shows the least value while that for the STH shows the largest value. This pattern is consistent with the screenline analysis and the overall relationship between %RMSE and ground count volume groups. Area specific volume analysis provides another broad statewide measure of the performance of the overall model. The truck traffic in the North area with 26 check points, the West area with 36 check points, the East area with 29 check points, and the South area with 64 check points are compared to the actual ground count totals. The four areas show similar results. No specific patterns in the L V/GC ratio by area are found. In addition, the %RMSE is computed for each of the four areas. The %RMSEs for the North, West, East, and South areas are 92%, 49%, 27%, and 35% respectively, whereas, the average ground counts are 481, 1383, 1532, and 3154 respectively. As for the screenline and volume range analyses, the %RMSE is inversely related to average link volume. 'The SELINK adjustments of productions and attractions resulted in a very substantial reduction in the total in-state zonal productions and attractions. The initial in-state zonal trip generation model can now be revised with a new trip production's trip rate (total adjusted productions/total population) and a new trip attraction's trip rate. Revised zonal production and attraction adjustment factors can then be developed that only reflect the impact of the SELINK adjustments that cause mcreases or , decreases from the revised zonal estimate of productions and attractions. Analysis of the revised production adjustment factors is conducted by plotting the factors on the state map. The east area of the state including the counties of Brown, Outagamie, Shawano, Wmnebago, Fond du Lac, Marathon shows comparatively large values of the revised adjustment factors. Overall, both small and large values of the revised adjustment factors are scattered around Wisconsin. This suggests that more independent variables beyond just 226; population are needed for the development of the heavy truck trip generation model. More independent variables including zonal employment data (office employees and manufacturing employees) by industry type, zonal private trucks 226; owned and zonal income data which are not available currently should be considered. A plot of frequency distribution of the in-state zones as a function of the revised production and attraction adjustment factors shows the overall " adjustment resulting from the SELINK analysis process. Overall, the revised SELINK adjustments show that the productions for many zones are reduced by, a factor of 0.5 to 0.8 while the productions for ~ relatively few zones are increased by factors from 1.1 to 4 with most of the factors in the 3.0 range. No obvious explanation for the frequency distribution could be found. The revised SELINK adjustments overall appear to be reasonable. The heavy truck VMT analysis is conducted by comparing the 1990 heavy truck VMT that is forecasted by the GM truck forecasting model, 2.975 billions, with the WisDOT computed data. This gives an estimate that is 18.3% less than the WisDOT computation of 3.642 billions of VMT. The WisDOT estimates are based on the sampling the link volumes for USH, 8TH, and CTH. This implies potential error in sampling the average link volume. The WisDOT estimate of heavy truck VMT cannot be tabulated by the three trip types, I-I, I-E ('||'&'||'pound;-I), and E-E. In contrast, the GM forecasting model shows that the proportion ofE-E VMT out of total VMT is 21.24%. In addition, tabulation of heavy truck VMT by route functional class shows that the proportion of truck traffic traversing the freeways and expressways is 76.5%. Only 14.1% of total freeway truck traffic is I-I trips, while 80% of total collector truck traffic is I-I trips. This implies that freeways are traversed mainly by I-E and E-E truck traffic while collectors are used mainly by I-I truck traffic. Other tabulations such as average heavy truck speed by trip type, average travel distance by trip type and the VMT distribution by trip type, route functional class and travel speed are useful information for highway planners to understand the characteristics of statewide heavy truck trip patternS. Heavy truck volumes for the target year 2010 are forecasted by using the GM truck forecasting model. Four scenarios are used. Fo~ better forecasting, ground count- based segment adjustment factors are developed and applied. ISH 90 '||'&'||' 94 and USH 41 are used as example routes. The forecasting results by using the ground count-based segment adjustment factors are satisfactory for long range planning purposes, but additional ground counts would be useful for USH 41. Sensitivity analysis provides estimates of the impacts of the alternative growth rates including information about changes in the trip types using key routes. The network'||'&'||'not;based GMcan easily model scenarios with different rates of growth in rural versus . . urban areas, small versus large cities, and in-state zones versus external stations. cities, and in-state zones versus external stations.
The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70
The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70
본 연구는 서비스 시장에서의 지각된 품질과 개인가치간의 인과적 관계 및 고객의 인지욕구에 따른 온 오프라인상의 조절효과에 대해 실증분석하였으며 이를 통해 개인가치에 대한 서비스 전략과 마케팅 관리의 중요성을 제시하고 있다. 서비스 시장에서 서비스 제공자와 구매자간의 장기적 거래관계의 중요성이 크게 부각됨에 따라 관계구축 및 강화에 매우 중요한 역할을 하는 개인가치에 관한 연구는 학계뿐만 아니라 실무적으로도 고객관계관리의 관점에서 시사하는 바가 크다고 할 수 있다. 실증분석을 위해 대형마트(할인점)와 인터넷 쇼핑몰을 이용하는 고객을 대상으로 설문을 통해 데이터를 수집하였으며 온 오프라인의 비교분석을 통한 차이검증을 위한 인과적 구성모델에 대해 구조방정식 모델분석을 통해 가설검증하였다. 구성모델에 대한 분석결과 물리적 환경, 상호작용 품질, 그리고 결과품질로 구성된 지각된 품질은 안정적 삶, 사회적 인식, 사회적 통합으로 구성된 서비스 개인가치에 통계적으로 매우 유의한 정(+)의 영향을 미치는 것으로 나타났으며 집단간 차이효과분석을 통해서도 온 오프라인에 따른 조정효과는 온라인에서보다는 오프라인에서 더 유의한 것으로 나타났다. 그리고 온라인상에서의 서비스에 대한 인지욕구가 높을 때보다는 오프라인상에서의 서비스에 대한 인지욕구가 높을 때 개인가치에 더 유의한 영향을 미치는 것으로 나타났다. 마지막으로 본 연구의 구성모델에 대한 적합도 역시 수용할만한 수준인 것으로 나타났다.
본 연구는 최근 사회경제적 이슈가 되고 있는 동반성장의 개념과 실천 방향에 대해 논의하고자 한다. 이를 위해 동반성장의 정책적 개념을 살펴보고 유사한 개념인 상생협력과 공생발전과도 비교 분석하고자 한다. 또한 동반성장을 통해 글로벌 경쟁력을 만들어 낸 선진국 사례들로부터 교훈을 찾아내고 우리의 사회 문화적 특성에 맞는 한국형 모델을 제안하고자 한다. 한국형 동반성장 모델은 미국의 시장중심형, 일본의 문화기반형, 유럽의 정책주도형 등의 장점을 융합할 필요가 있다. 이를 위해 한국형 모델은 공동체적 에너지를 창출해내는 한국인의 잠재력 활용, 통제와 자율의 융합형 제도 개선, 미래지향적 협력관계를 위한 기업들의 행동변화 등 세 가지 요인을 핵심으로 할 필요가 있다. 한국형 모델의 실현을 위해 필요한 정부의 역할과 과제, 그리고 동반성장위원회의 역할에 대해서도 논의하고자 한다.