• KSBB Journal
• /
• v.8 no.5
• /
• pp.431-437
• /
• 1993

Active carbon which has the smallest bulk and wet density was found as the best support media among 4 different kinds of materials(celite, natural zeolite, Pusuk stone, active carbon) to make a proper fluidized-bed with small energy consumption. Its minimum and optimum fluidization velocity were found as 0.03cm/sec and 0.25cm/sec, respectively. As organic loading rate for methane fermentation was increased, CODcr removal efficiencies of all the media were decreased. But, CODcr, removal efficiencies of active carbon was maintained more than 90% in this experimental range of the organic loading rate. Larger amount of microorganism was adsorbed on the active carbon which has very high specific surface area. At the organic loading rate of 16g CODcr,/l day, its adsorbed cell mass was 157mg/g. Comparing natural zeolite with roast celite, adsorbed cell mass did not increase in proportion to specific surface area of the media. Even though roast celite has the same specific surface area as the Pusuk stone, its organic removal ability was superior to that of the Pusuk stone, which explains that the relatively great surface roughness and the positive surface charge are important for cell adsorption. It was concluded that the support media for anaerobic fluidized reactor should have small wet density and small fuidization velocity, if possible, in order to increase cell adsorption by reducing the fluid shear stress.

• Journal of the Korean Chemical Society
• /
• v.57 no.5
• /
• pp.634-639
• /
• 2013

The use of medical imaging has been increased for diagnosis of cancer or vessel disease. Among the medical imaging, computed tomography (CT) is one of the popular methods, however, which should need administration of contrast medium. Therefore, we developed gold coated liposomes (GCL) as a contrast medium. To coat gold on the liposomal surface, positive charged liposomes was prepared and then negative $Au^-$ can coat on the liposomal surface by electronic interaction. The size of GCL was $154.8{\pm}9.2$ nm and surface charge was $27{\pm}3.2$ mV, respectively. The morphology of GCL was confirmed by electron microscopy (SEM) and transmission electron microscopy (TEM). The coating efficiency of gold was 18%. Chemical procedure for gold coating on liposomal surface was not toxic for cell cytotoxicity by MTT assay. Finally, we demonstrated attractive CT image for GCL. Taken together, the GCL would be useful for various vessel related disease as a contrast medium.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.5
• /
• pp.448-454
• /
• 2000

This study was to examine the physicochemical characteristics of coagulation reaction between ignited oyster shell powder (IOSP) and red tide organisms (RTO), and its feasibility, in developing a technology for the removal of RTO bloom in coastal sea,IOSP was made from oyster shell and its physicochemical characteristics were examined for particle size distribution, surface characteristic by scanning electron microscope, zeta potential, and alkalinity and pH variations in sea water. Two kinds of RTO that were used in this study, Cylindrotheca closterium and Skeletonema costatum, were sampled in Masan bay and were cultured in laboratory. Coagulation experiments were conducted using various c(Incentrations of IOSP, RTO, and a jar tester. The supernatant and RTO culture solution were analyzed for pH, alkalinity, RTO cell number, IOSP showed positive zeta potentials of $11.1{\~}50.1\;mV\;at\;pH\;6.2{\~}12.7$, A positive zeta potential of IOSP slowly decreased with decreasing pNa 4,0 to 2,0. When pNa reached zero, the zeta potential approached zero, When a pMg value was decreased, the positive zeta potential of IOSP increased until pMg 3.0 and decreased below pMg 3.0. IOSP showed 4.8 mV of positive zeta potential while RTO showed -9.2 mV of negative zeta potential in sea water. A positive-negative EDL (electrical double-layer) interaction occurred between $Mg(OH)_2$ adsorption layer of IOSP and RTO in sea water so that EDL attractive force always worked between them. Hence, their coagulation reaction occurred at primary minimum on which an extreme attractive force acted because of charge neutralization by $Mg(OH)_2$ adsorption layer of IOSP. As a result, the coagulation reaction was rapidly processed and was irreversible according to DLVO (Deriaguin-Landau-Verwey-Overbeek) theory. Removal rates of RTO were exponentially increased with increasing both IOSP concentration and G-value. The removal rates were steeply increased until 50 mg/l of IOSP and reached $100{\%}\;at\;400\;mg/l$ of IOSP. Removal rates of RTO were $70.5,\;70.5,\;81.7,\;85.3{\%}$ for G-values of $1,\;6,\;29,\;139\;sec^(-1)$at IOSP 100 mg/l, respectively. This indicated that mixing (i.e., collision among particles) was very important for a coagulation reaction.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.241-241
• /
• 2008

Macrofore formation in silicon and other semiconductors using electrochemical etching processes has been, in the last years, a subject of great attention of both theory and practice. Its first reason of concern is new areas of macropore silicone applications arising from microelectromechanical systems processing (MEMS), membrane techniques, solar cells, sensors, photonic crystals, and new technologies like a silicon-on-nothing (SON) technology. Its formation mechanism with a rich variety of controllable microstructures and their many potential applications have been studied extensively recently. Porous silicon is formed by anodic etching of crystalline silicon in hydrofluoric acid. During the etching process holes are required to enable the dissolution of the silicon anode. For p-type silicon, holes are the majority charge carriers, therefore porous silicon can be formed under the action of a positive bias on the silicon anode. For n-type silicon, holes to dissolve silicon is supplied by illuminating n-type silicon with above-band-gap light which allows sufficient generation of holes. To make a desired three-dimensional nano- or micro-structures, pre-structuring the masked surface in KOH solution to form a periodic array of etch pits before electrochemical etching. Due to enhanced electric field, the holes are efficiently collected at the pore tips for etching. The depletion of holes in the space charge region prevents silicon dissolution at the sidewalls, enabling anisotropic etching for the trenches. This is correct theoretical explanation for n-type Si etching. However, there are a few experimental repors in p-type silicon, while a number of theoretical models have been worked out to explain experimental dependence observed. To perform ordered macrofore formaion for p-type silicon, various kinds of mask patterns to make initial KOH etch pits were used. In order to understand the roles played by the kinds of etching solution in the formation of pillar arrays, we have undertaken a systematic study of the solvent effects in mixtures of HF, N-dimethylformamide (DMF), iso-propanol, and mixtures of HF with water on the macrofore structure formation on monocrystalline p-type silicon with a resistivity varying between 10 ~ 0.01 $\Omega$ cm. The etching solution including the iso-propanol produced a best three dimensional pillar structures. The experimental results are discussed on the base of Lehmann's comprehensive model based on SCR width.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.384.1-384.1
• /
• 2016

We reported that amorphous silicon (a-Si) thin film provide sample plate exhibiting a multimodality to measure biomolecules by secondary ion mass spectrometry (SIMS) and laser desorption/ionization mass spectrometry (LDI-MS). Kim et al.1 reported that a-Si thin film were suitable to detect small molecules such as drugs and peptides by SIMS and LDI-MS. Recently, bacterial identification has been required in many fields such as food analysis, veterinary science, ecology, agriculture, and so on.2 Mass spectrometry is emerging for identifying and profiling microbiology samples from its advantageous characters of label-free and shot-time analysis. Five species of bacteria - S. aureus, G. glutamicum, B. kurstaki, B. sphaericus, and B. licheniformis - were sampled for MS analysis without lipid extraction in sample preparation steps. The samples were loaded onto the a-Si thin film with a thickness of 100 nm which did not only considered laser-beam penetration but also surface homogeneity. Mass spectra were recorded in both positive and negative ionization modes for more analytical information. High reproducibility and sensitivity of mass spectra were demonstrated in a mass range up to mass-to-charge ratio(m/z) 1200 by applying the a-Si thin film in mentioned above MS. Principle component analysis (PCA) - a popular statistical analysis widely used in data processing was employed to differentiate between five bacterial species. The PCA results verified that each bacterial species were readily distinguished and differentiated effectively from our MS approach. It shows a new opportunity to rapid bacterial profiling and identification in clinical microbiology. More details will be discussed in the presentation.

• Journal of Environmental Health Sciences
• /
• v.46 no.5
• /
• pp.599-609
• /
• 2020

Objectives: Coronavirus disease 2019 (COVID-19) first emerged in December 2019 in Wuhan, China, and has rapidly become a global pandemic with over 26.4 million confirmed cases and approximately 871,000 fatalities worldwide as of this writing. In the Republic of Korea, disease clusters frequently occurred in long-term care hospitals where the majority of residents are elderly with underlying medical conditions. Despite the fact that public health authorities and local community health centers have put tremendous efforts into preventing the spread of disease, positive cases have continued to occur. Thus, the Korea Centers for Disease Control & Prevention rapid response team decided to conduct an environmental investigation of a long-term care hospital to identify whether environmental contamination has remained and contributed to the spread of COVID-19. Methods: An environmental investigation was conducted at Hospital A. The characteristics of the facility and its HVAC system were assessed by checking the layout and interviewing the people in charge. A total of 64 surface samples were collected from areas of concern, including patient rooms, toilets, elevators, and nurses' station. These samples were tested by a regional health and environmental research institute using real-time reverse transcription polymerase chain reaction. Results: All samples from Hospital A were confirmed to be negative. Through interviews with high-level personnel at the regional community health center, we found that extensive disinfection is frequently performed on potentially contaminated areas in Hospital A in accordance with government guidelines. Conclusion: The environmental control measures implemented in Hospital A had been sufficient for mitigating the risk of further infection, suggesting that such measures may also be effective for other long-term health care facilities.

• Journal of the Mineralogical Society of Korea
• /
• v.15 no.3
• /
• pp.183-194
• /
• 2002

Biotite and its weathering Products in the weathering Profile of Andong granite were examined using X-ray diffraction, chemical analysis, and electron microscopy. Major weathering product of biotite was oxidized biotite, which is decomposed into kaolinite in the upper part. Discrete vermiculite or hydrobiotite was not detected although minor vermiculite (5%) was randomly interstratified with oxidized biotite. Excess positive charge induced by iron oxidation was balanced by release of Fe (16%) and Mg (12%) from octahedral site and K (13%) from interlayer site. After slight chemical and structural modification induced by iron oxidation, oxidized biotite persists through the weathering profiles with partial decomposition in the upper part of the profile. Formation environments and dissolution experiments of oxidized biotite highly resistant to weathering are required to understand the elemental behavior in the surface environments on the biotite-bearing bedrocks.

• Journal of Microbiology and Biotechnology
• /
• v.30 no.8
• /
• pp.1261-1271
• /
• 2020

Cytochrome c_L (Cytc_L) is an essential protein in the process of methanol oxidation in methylotrophs. It receives an electron from the pyrroloquinoline quinone (PQQ) cofactor of methanol dehydrogenase (MDH) to produce formaldehyde. The direct electron transfer mechanism between Cytc_L and MDH remains unknown due to the lack of structural information. To help gain a better understanding of the mechanism, we determined the first crystal structure of heme c containing Cytc_L from the aquatic methylotrophic bacterium Methylophaga aminisulfidivorans MP^T at 2.13 Å resolution. The crystal structure of Ma-Cytc_L revealed its unique features compared to those of the terrestrial homologues. Apart from Fe in heme, three additional metal ion binding sites for Na⁺, Ca⁺, and Fe²⁺ were found, wherein the ions mostly formed coordination bonds with the amino acid residues on the loop (G93-Y111) that interacts with heme. Therefore, these ions seemed to enhance the stability of heme insertion by increasing the loop's steadiness. The basic N-terminal end, together with helix α4 and loop (G126 to Y136), contributed positive charge to the region. In contrast, the acidic C-terminal end provided a negatively charged surface, yielding several electrostatic contact points with partner proteins for electron transfer. These exceptional features of Ma-Cytc_L, along with the structural information of MDH, led us to hypothesize the need for an adapter protein bridging MDH to Cytc_L within appropriate proximity for electron transfer. With this knowledge in mind, the methanol oxidation complex reconstitution in vitro could be utilized to produce metabolic intermediates at the industry level.

• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.12
• /
• pp.1712-1716
• /
• 2004

Copper-bearing montmorillonite (Cu-MMT) was produced by $Cu^{2+}$ cation exchange reaction. X-ray diffraction analysis showed that that the (001) basal spacing of the MMT crystal lattice increased from 1.544 to 1.588 nm after $Cu^{2+}$ exchange. This indicated that $Cu^{2+}$ entered into interlayer position of MMT as a hydrated cation or composite cation. In vitro results indicated that Cu-MMT had antibacterial activity on Escherichia coli $K_{88}$. Cu-MMT had unbalanced positive charge after cation exchange. Its antibacterial activity resulted from two aspects, one was electrostatic attraction which made E. coli $K_{88}$ being adhered on the montmorillonite surface, the other was the $Cu^{2+}$ slowly released, which could kill bacteria. In an in vivo study, four replicates of eight weanling pigs were assigned to each of two dietary treatments to study the effects of Cu-MMT on diarrhea, E. coli in the lumen of the jejunum and morphology of jejunal mucosa. As compared to the control, supplementation of the diet with 0.2% Cu-MMT improved average daily gain by 12.50% (p<0.05) and decreased F/G by 9.42% (p<0.05). The mean diarrhrea incidence was decreased by 71.80% (p<0.05). The viable counts of Escherichia coli in jejunal contents were significantly reduced (p<0.05). Villus height and the villus height to crypt depth ratio at the jejunal mucosa were increased by 19.09% (p<0.05) and 37.10% (p<0.05), respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.76-76
• /
• 2011

Polymer-fullerene based bulk heterojunction (BHJ) solar cells can be fabricated in large area using low-cost roll-to-roll manufacturing methods. However, because of the low mobility of the BHJ materials, there is competition between the sweep-out of the photogenerated carriers by the built-in potential and recombination within the thin BHJ film [12-15]. Useful film thicknesses are limited by recombination. Thus, there is a need to increase the absorption by the BHJ film without increasing film thickness. Metal nanoparticles exhibit localized surface plasmon resonances (LSPR) which couple strongly to the incident light. In addition, relatively large metallic nanoparticles can reflect and scatter the light and thereby increase the optical path length within the BHJ film. Thus, the addition of metal nanoparticles into BHJ films offers the possibility of enhanced absorption and correspondingly enhanced photo-generation of mobile carriers. In this work, we have demonstrated several positive effects of shape controlled Au and Ag nanoparticles in organic P3HT/PC70BM, PCDTBT/PC70BM, Si-PCPDTBT/PC70BM BHJ-based PV devices. The use of an optimized concentration of Au and Ag nanomaterials in the BHJ film increases Jsc, FF, and the IPCE. These improvements result from a combination of enhanced light absorption caused by the light scattering of the nanomaterials in an active layer. Some of the metals induce the plasmon light concentration at specific wavelength. Moreover, improved charge transport results in low series resistance.