• 한국가구학회지
• /
• 제10권1호
• /
• pp.65-71
• /
• 1999

The bending performance of sloped finger-jointed Rhus verniciflua were tested in order to improve the strength properties of finger-joint. Sloped finger-cut pieces were jointed with three kinds of adhesives (polyvinyl acetate, polyvinyl-acryl acetate and oilic resin). The slope ratios of finger joints were 0, 1.0, 1.5, and 2.0. The MOE, MOR and deflection to maximum load in bending of sloped finger-joints and solid wood specimen were measured. The results were : 1) The efficiencies of MOE to finger and sloped finger-joints to the solid wood were almost same in the three kinds of adhesives(polyvinyl acetate, polyvinyl-acryl acetate and oilic urethane resin) and there were some effect of slope on the MOE in a sloped finger-joint for three kinds of resin adhesives. 2) There was the effect of slope on the MOR in sloped finger-joints in every kind of adhesive. The efficiencies of MOR in slope ratios of 0 and 2.0 ranged 65-79%, respectively. There was also a slight effect of the kinds of adhesives on the MOR. However, the efficiencies of deflection to the urethane resin adhesive were much less than those of polyvinyl acetate, polyvinyl-acryl acetate resin adhesives except the slope ratio of 0. 3) It might be impossible to estimate the bending stregth of sloped finger-jointed Rhus verniciflua by using MOE. The correlation coefficient(0.192) between MOE was very low and not significant at 5% level.

• 한국가구학회지
• /
• 제10권2호
• /
• pp.73-78
• /
• 1999

This paper describes the relationship between the bending strength properties of sloped finger-jointed woods and the acoustic emissions(AEs) generated during the test. Rhus verniciflua pieces were cut in sloped-finger types and glued with three kinds of adhesives(polyvinyl acetate, polyvinyl-acryl acetate and oilic urethane resin). The slope ratios of finger joints were 0, 1.0, 1.5, and 2.0. The AE cumulative event count and cumulative count were measured during the bending test. The results were as follows: The lower the bending strength(load) was, the generation time of AE event count got and the higher the increasing rate of AE event count became in the sloped finger-jointed specimens bonded with polyvinyl acetate, polyvinyl-acryl acetate oilic urethane resin adhesives. Therefore, the slope from load-AE cumulative event count was very steep. The patterns of AE event count and count were very similar. The relationship between the MOR and the AE parameter from load and AE cumulatve event count in the early stage of the sloped finger-jointed specimens bonded with polyvinyl acetate, polyvinyl-acryl and oilic urethane resin adhesives was much greater than that between the MOE and the MOR. Therefore, the AE signals obtained during bending test are useful for estimating the strength of sloped finger-jointed Rhus verniciflua specimens.

• Journal of the Korean Wood Science and Technology
• /
• 제25권4호
• /
• pp.61-67
• /
• 1997

The bending performances of sloped finger-joints in Pinus densiflora S. et Z. were tested in order to improve the strength properties of finger-joint Sloped finger-cut pieces were jointed with four kinds of adhesives(resorcinol-phenol, oilic urethane, polyvinyl acetate, and polyvinyl-acryl acetate resin). The slope ratios of finger joints were 0, 0.5, 1.0, 2.0. The MOE, MOR and defletion to maximum load in bending of sloped finger-joints and solid wood specimen were measured. The results were: 1. The efficiencies of MOE to finger and sloped finger-joints were 82% or greater in every kind of adhesives except polyvinyl-acryl acetate resin adhesive and there were some effect of slope on the MOE in a sloped finger-joint for polyvinyl-acryl acetate and oilic urethane resin adhesives. 2. The effects of slope on the MOR to sloped finger-joints were showed in every kind of adhesive, because the efficiencies of MOR increased with increasing slope ratio in sloped finger-joints. The efficiencies of MOR to slope ratios of 0 and 2.0 ranged 43~65% and 76~82%, respectively. There was almost no effect of the kinds of adhesives on the MOR to the slope ratio of 2.0. 3. It was found impossible to estimate the bending strength of sloped finger-jointed Pinus densiflora S. et Z. by using MOE. The correlation coefficient(0.124) between MOE and MOR was very low and not significant at 5% level.

• 공업화학
• /
• 제28권4호
• /
• pp.437-441
• /
• 2017

본 연구에서는 방화용 실란트의 첨가제로 사용되는 팽창흑연의 부피팽창률과 경도특성을 개선하기 위해 팽창흑연에 다양한 수지를 코팅한 후 그 특성을 고찰하였다. 수지의 코팅률을 나타내는 평균코팅두께는 수지의 건조속도와 점도의 영향으로 초산비닐계수지 > 아크릴수지 > 우레탄수지 > 수용성라텍스의 순으로 크게 나타났다. 또한 수지의 종류에 따라 코팅된 팽창흑연의 부피팽창률은 우레탄수지 > 수용성라텍스 > 아크릴수지 > 초산비닐계수지의 순으로 컸으며, 경도는 초산비닐계수지 > 아크릴수지 > 수용성라텍스 > 우레탄수지의 순으로 증가함을 알 수 있었다. 이는 코팅처리를 하지 않은 팽창흑연에 비해 부피팽창률은 감소하나 경도가 현저하게 증가되어 방화첨가제로 사용이 가능함을 알 수 있었다. 반응표면분석법에 의한 최적화실험 결과 아크릴수지의 최적코팅 조건은 수지의 첨가량 37.6 wt%과 코팅 교반속도 441.4 rpm이었다.

• Journal of the Korean Wood Science and Technology
• /
• 제27권1호
• /
• pp.30-36
• /
• 1999

소나무를 재료로 경사핑거접합법으로 레소시놀계수지, 유용성 우레탄수지, 초산비닐수지, 초산비닐과 아크릴을 혼합한 수지접착제롤 사용하여 제작한 시험재의 휨강도 성능과 휨 시험시 발생하는 AE 특성에 대한 연구결과는 다음과 같다. 초산 비닐, 유용성 우레탄 수지접착제를 사용한 소나무경사 핑거접합재의 하중과 AE 사상총수는 휨 강도가 낮을수록 빠른 시기부터 AE가 발생하고 AE의 증가속도가 빨라 하중-AE 사상총수의 관계곡선의 기울기가 급격하게 나타났다. 레소시놀 수지 접착제로 제작한 시편은 아주 낮은 하중에서부터 하중이 증가함에 따라 연속적으로 AE가 발생하였고 발생수도 많았다. 경사 핑거접착제의 휨 하중과 AE 특성간에는 서로 잘 대응되어 휨강도 측정이나 보정은 휨 탄성계수로서는 예측이 어렵지만 하중과 AE, 사상총수의 초기 치로부터 얻어지는 AE지표 치로서 휨 강도의 예측이나 보증이 가능 할 것으로 판단된다.

• 한국가구학회지
• /
• 제12권2호
• /
• pp.1-10
• /
• 2001

As finger joint method has a high rate of yield and high strength and ease in working, it has been widely used as an end joint method for solid wood and wood based-material. Therefore, we end-joined the material of Pinus densiflora, Quercus variabilis and populus euramericana with polyvinyl acetate adhesive and resorcinol phenol resin adhesive. The effect of difference (0, 0.15, 0.3, 0.45mm) between the dimensions of tip width and root width of the finger (DTRW) on bending strength properties was as follows: 1. In the case of polyvinyl acetate adhesive, DTRW had no effect on bending modulus of elasticity(MOE) and modulus of rupture(MOR) of the three kinds of species, because their bonding layers were destroyed by slippage, not their woody parts. 2. In the case of resorcinol phenol resin adhesive, the material of Quercus variabilis showed an optimal result at 0.15 or 0.3 of DTRW, while the poplar did at 0 of DTRW 3. The differences in efficiency ratio of bending MOR of populus euramericana, Pinus densiflora and Quercus variabilis species according to the kind of adhesive were 13-29%, 23-30% and 45-53%, respectively.

• 한국가구학회지
• /
• 제11권1호
• /
• pp.25-29
• /
• 2000

This study was carried out to analyze the ultrasonic properties of sound board which was glued with various adhesives and to evaluate which adhesive is the best for the acoustic radiation of the musical instrument. The results are as follows: 1. Animal glue is the best adhesive for the sound board with respect to the acoustic radiation ratio of the musical instruments. Epoxy resin and polyvinyl acetate resin are the next group, urea formaldehyde resin and Hot melt are the third group, polychloroprene(CR) resin is the lowest. 2. Epoxy resin, animal glue and Titebond(PVA) give the highest shear strength and the highest wood failure relatively Hot melt and polychloroprene(CR) resin do not meet the standard because of low wood failure.

• 한국가구학회지
• /
• 제16권1호
• /
• pp.1-8
• /
• 2005

This experiment was carried out to investigate the gluing characteristics of poly vinyl acetate emulsion adhesive(PVAc) on the Cryptomeria japonica laminated boards. This sample trees are major planting species and have been planted in southern district for a long time. The optimum gluing conditions for laminated board were summarized as follows; the amount of spreading glue, assembly time, clamping pressure, and clamping time for PVAc resin were $200g/m^2$, 10min., $5kg/cm^2$, and 6hrs., respectively, and the relative formulae between extension ratio(x) and block shear strength(y) was $y=-9.6x+85.2(R^2=0.95)$.

• Journal of the Korean Wood Science and Technology
• /
• 제39권2호
• /
• pp.156-162
• /
• 2011

To evaluate the bonding performance of reinforced glulam, the textile type of glass fiber and aramid fiber, and the sheet type of glass fiber reinforced plastic (GFRP) and carbon fiber reinforced plastic (CFRP) were used as reinforcements. The reinforced glulam was manufactured by inserting reinforcement between the outmost and middle lamination of 5ply glulam. The types of adhesives used in this study were polyvinyl acetate resins (MPU500H, and MPU600H), polyurethane resin and resorcinol resin. The block shear strengths of the textile type in glass fiber reinforced glulam using MPU500H and resorcinol resin were higher than 7.1 N/$mm^2$, and these glulams passed the wood failure requirement of Korean standards (KS). In case of the sheet types, GFRP reinforced glulams using MPU500H, polyurethane resin and resorcinol resin, and CFRP reinforced glulams using MPU500H and polyurethane resin passed the requirement of KS. The textile type of glass fiber reinforced glulam using resorcinol resin after water and boiling water soaking passed the delamination requirement of KS. The only GFRP reinforced glulam using MPU500H after water soaking passed the delamination requirement of KS. We conclude that the bonding properties of adhesive according to reinforcements are one of the prime factors to determine the bonding performance of the reinforced glulam.

• 한국가구학회지
• /
• 제17권2호
• /
• pp.25-34
• /
• 2006

This experiment was carried out to investigate the high-frequency gluing characteristics of poly vinyl acetate emulsion adhesive(PVAc) on MDF edge-glued boards. The edge-glued boards were glued lengthwise with butt, scarf, or finger joint. The wastes of MDF boards were reused as board materials. The obtained results are summarized as follows; the bending strength of edge-glued MDF increased slightly with the HF heating time, but the economically desirable heating time was 6 minutes. The bending and tensile strength of edge-glued MDF were high with scarf, finger and butt joint, in order. The strength of finger jointed MDF showed 80% of scarf jointed MDF. The effects of location of finger joints on the bending strength of edge-glued MDF were larger than those of the numbers of finger joints. The bending strength of edge-glued MDF with one joint on the middle position showed 40% decrease in comparison with non-jointed MDF.