• Journal of the Korean Applied Science and Technology
• /
• v.15 no.2
• /
• pp.59-66
• /
• 1998

Two-packaged polyurethane coatings were prepared by blending benzoic acid lactone modified polyester polyol(BLMPs) and HDI-biuret. BLMPs were synthesized by polycondensation of benzoic acid, viscosity depression component, with 1,4-butanediol, adipic acid, and polycaprolactone polyol. Kinematic viscosity of BLMP was gradually decreased with increasing benzoic acid content in BLMP. The low viscosity of modified polyester has an advantage of making a high-solid content coatings. After the film was coated with the prepared polyurethane coatings and cured at room temperature, the various physical properties were measured. They showed good physical properties such as flexibility, impact resistance, cross hatch adhesion, yellowness index, and rust resistance. These advantages are the results of introducing polycaprolactone polyol.

• Investigative Magnetic Resonance Imaging
• /
• v.13 no.2
• /
• pp.171-176
• /
• 2009

Purpose : To investigate the effect of coating material in RF coil, which is one of main parts in MRI machine, on the Q-factor and SNR(signal-to-noise ratio) in MR images. Materials and Methods : RF coils with inner diameter of 1.7 mm were made by using copper wires coated with polyester, polyurethane, polyimide, polyamideimide, and polyester-imide, and by using copper wires in which coating materials had been removed. Q-factors of the RF coils were measured by network analyzer, and SNR values in the spin-echo MR images obtained by 600 MHz (14.1 T, Bruker DMX600) micro-imaging system for the coated and uncoated cases. Results : The measured SNRs were almost same for the RF coils with coat-removed copper wires, however SNRs and Q-factors were different for the coated cases depending on the coating material. They were maximized in the polyurethane-coated case in which the SNR was > 30% greater than polyester-coated case. Conclusion : We made solenoid-type RF coils which were easily used for MR micro-imaging in Bruker MRI probe. There was a significant coating-material dependence in the measured Q values and SNRs for the home-made RF coils. The study demonstrated that the choice of coating material of RF coil may be a critical factor in the MRI sensitivity based on SNR value.

• Textile Coloration and Finishing
• /
• v.24 no.1
• /
• pp.54-61
• /
• 2012

This study surveyed the preparation of 8oz coated fabric and the physical property of the coated fabric according to the treated condition for the sail yacht. And the coated fabrics were compared with the performance of overseas products for verification. Physical properties of the coated fabric treated with non-yellowing functional polyurethane resin were examined according to the treatment condition such as compression and ageing treatments. Finally, yellowing fastness to light for 60 hours was assessed. Considering the compression condition after coating, good physical property was obtained at $6kgf/cm^2$. Also, the performance of yellowing fastness was similar to performance of overseas goods.

• Journal of Adhesion and Interface
• /
• v.19 no.3
• /
• pp.118-122
• /
• 2018

In this study, polyurethane hot melt adhesive containing ester groups was synthesized. Three kinds of chain extenders were used to find out the best chain extender. Results showed that adhesive containing 1,4-butanediol as a chain extender exhibited the highest peel strength among them. Also, it was found that there existed the optimum molecular weight of 1,4-butanediol containing adhesive for make the highest peel strength.. Moreover, hot melt adhesive containing 1,4-butanediol chain extender was applied to various kinds of textiles substrate such as cotton, polyester, and urethane coated polyester textiles to study the effects of different substrates on the peel strength and water resistance at $60^{\circ}C$. It was found that cotton substrate showed the highest peel strength and urethane coated polyester substrate showed the highest resistance on $60^{\circ}C$ water.

• Textile Coloration and Finishing
• /
• v.18 no.3 s.88
• /
• pp.31-41
• /
• 2006

Functional properties are available with sputtering. But sputtering treatment alone cannot got a good fastness performance to washing, rubbing and light. This research was objected to investigate optimum condition by sputtering on polyester through various processing conditions such as ion current and treatment time, and then various resin treated onto metal coated polyester fabrics in order to increase washing fastness of metal membrane. As the results, the optimum conditions revealed 1500 mA of ion current, 2 min of treatment time in sputter, and suitable resin concentrations were 2% of o.w.s (on the weight of solution) in resin treatment. Therefore, we could get enhanced anti-static effect and flex stiffness as well as washing fastness in sputtered polyester fabric with various resin treatment, for example, melamine and polyurethane.

• Polymer(Korea)
• /
• v.24 no.1
• /
• pp.72-81
• /
• 2000

Benzoic acid polyester/lactone polyol were synthesized by polycaprolactone 0201 as diol, trimethylolpropane as triol, adipic acid as dibasic acid, and benzoic acid as monobasic acid. Polyisocyanate prepolymer Desmodur N-100 of HDI-biuret type was used in this study. Two-component polyurethane coatings were prepared by blending benzoic acid polyester/polycaprolactone, polyisocyanate, wetting/dispersing agent, white pigment, and flowing agent. Various properties were examined on the film coated with the prepared polyurethane. They showed excellent physical properties such as abrasion resistance, accelerated weathering resistance, and yellowness index. They also showed good physical properties such as flexibility, impact resistance, 60$^{\circ}$ specular gloss, cross hatch adhesion, hydrocarbon resistance, and lightness index difference. Hardness of coating showed a little poor character. The introduction of polycaprolactone 0201 as diol in the polyurethane coatings improved the hydrocarbon resistance, impact resistance, and flexibility of coatings. According to the drying and curing behavior with the contents of benzoic acid, they seem to have reasonable coating properties such as drying time of 2 to 4 hours and pot-life time of 20 to 37 hours.

• Textile Coloration and Finishing
• /
• v.31 no.4
• /
• pp.258-267
• /
• 2019

Synthetic suede without PFCs(perfluorinated compounds) are followed by subsequent high temperature treatment. But migration fastness of synthetic suede may be reduced due to sublimation of disperse dyes that results from the high temperature treatment. Therefore, in this study, chitosan treatment was used to improve the migration fastness before polyurethane dipping process. Polyester fiber was treated with sodium hydroxide aqueous solution before chitosan processing. This samples treated with a chitosan concentration upto 0.5% were dyed and coated with PUD(polyurethane dispersion). The migration fastness was most improved at 0.35% application. This is presumably due to the fact that the chitosan may increase the dye-binding capability through intermolecular hydrogen bonding.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.32 no.11
• /
• pp.1792-1801
• /
• 2008

This study was to develope the pesticide-proof clothes(PPC) for fruit-grower which has been well known over applied agricultural chemicals. The ergonomic evaluation of PPC were tested in two ways. Male adults volunteered the tests to evaluate the safety to pesticide in the field and the thermal comforts in the climate-chamber($30^{\circ}C$, 60%R.H.). PPC were made of 4 different fabrics. Two of them were on the market(coated non-woven and coated nylon). Others were water-repellent treatment and coated waterproof film by developed polyester. The field study was conducted for farmers growing apples to evaluate pesticide exposure. In this experiment, we collected data with patch test on the head, chest, back, right upperarm, right forearm, left thigh and left calf. From the results, the developed PPC showed the more excellent comfort than an existing PPC with nylon coated polyurethane. But the developed PPC of water-repellent fabric was penetrated into the PPC. Therefore, we designed the functional pesticide-proof clothes of 2 different developed polyester fabrics(water-repellent treatment in chest, abdomen, the lower of back, waist, and calf; coated waterproof film in head, shoulder, the upper of back, the crotch, hip, upper arm and thigh).

• Fashion & Textile Research Journal
• /
• v.11 no.2
• /
• pp.359-362
• /
• 2009

This study investigates the behavior of water vapor permeability of a layered system to find out a comfortable combination of a layered system for outdoor activities and examines the water vapor permeability of various types of outdoor clothing fabrics. The layered system includes the base layer such as sportswool and polyester/cotton fabrics, the middle layer such as single and double sided fleece fabrics, and the shell layer such as polyurethane-coated, PTFE-laminated and microfiber fabrics in this experiment. Results show that the layered system was applied, it was working together as a whole having some influence on each other layer, though every layer offered varying degree of water vapor permeability. Water vapor permeability of layered system exactly followed the same trend as the shell layer, which is all vapor permeable water repellent fabrics as a single layer. The rate of water vapor transfer through a layered system is mainly related to the type of vapor permeable water repellent fabrics used for the shell layer.

• Journal of Adhesion and Interface
• /
• v.12 no.3
• /
• pp.99-104
• /
• 2011

Currently, automotive pre-primed coatings has been developed to overcome environmental regulations and to reduce manufacturing cost in automotive industry. By these reasons, an automotive pre-primed system has been investigated to remove the wash and pre-treatment process using a roll coating application. It is required to develop non-weldable pre-primed system for automotive structural adhesives, because pre-primed sheet coated with organic compounds is hard to be assembled by welding process. Primer 1 (polyester type) and primer 2 (urethane type) were designed to satisfy flexibility and formability for non-weldable pre-primed system. According to the results of physical property test of the primers, adhesion test such as single-lap shear test and T-peel test, primer 1 (polyester type) had better physical properties such as pencil hardness, solvent resistance, flexibility and adhesion with automotive adhesive than that of primer 2 (polyurethane type). In addition, the possibility of the non-weldable pre-primed system was applicable to automotive assembly process in place of welding process.