• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 가을 학술발표회 논문집
• /
• pp.260-265
• /
• 1996

Polyproplyene Fibers have many advantages such as light weight, low cost, chemical stability and duragbility. It has been reported that polypropylene fiber can increase the toughness of concrete and the resistance to crack formation. This study has been performed to investigate the dirability related properties such as permeability and diffusivity of polypropylene fiber reinforced concrete. The permeability and diffusivity were measured with GWT, Poroscope, and electrical conductivity of concrete. From the test result, it is found that the addition of the polypropylene fiber improved the permeability and diffusivity of concrete, when the workability reduction was corrected by water reducer. The relationships between the permeability and diffusivity, and other properties of polypropylene fiber reinforced concrete showed that the tesst results are interrelated each other.

• Computers and Concrete
• /
• 제22권2호
• /
• pp.209-220
• /
• 2018

In order to evaluate the effect of hybrid fibers on the flexural performance of tunnel segment at room temperature, twelve reinforced self-consolidating concrete (SCC) symmetric inclination beams containing steel fiber, macro polypropylene fiber, micro polypropylene fiber, and their hybridizations were studied under combined loading of flexure and axial compression. The results indicate that the addition of mono steel fiber and hybrid fibers can enhance the ultimate bearing capacity and cracking behavior of tested beams. These improvements can be further enhanced along with increasing the content of steel fiber and macro PP fiber, but reduced with the increase of the reinforcement ratio of beams. The hybrid effect of steel fiber and macro PP fiber was the most obvious. However, the addition of micro PP fibers led to a degradation to the flexural performance of reinforced beams at room temperature. Meanwhile, the hybrid use of steel fiber and micro polypropylene fiber didn't present an obvious improvement to SCC beams. Compared to micro polypropylene fiber, the macro polypropylene fiber plays a more prominent role on affecting the structural behavior of SCC beams. A calculation method for ultimate bearing capacity of flexural SCC symmetric inclination beams at room temperature by taking appropriate effect of hybrid fibers into consideration was proposed. The prediction results using the proposed model are compared with the experimental data in this study and other literature. The results indicate that the proposed model can estimate the ultimate bearing capacity of SCC symmetric inclination beams containing hybrid fibers subjected to combined action of flexure and axial compression at room temperature.

• Journal of the Korean Wood Science and Technology
• /
• 제15권3호
• /
• pp.44-55
• /
• 1987

In order to study the effect of sawdustboard combined with plastic chips, 0.5mm($T_1$), 1mm($T_2$), 1.4mm($T_3$) thick nylon fiber. polypropylene rope fiber(RP), and 0.23mm thick moth-proof polypropylene net fiber(NP) were cut into 0.5, 1, 2cm long plastic chips. Thereafter, sawdustboard combined with plastic chips prepared as the above and plastic non-combined sawdustboard(control) were manufactured into 3 types of one-, two-, and three layer with 5 or 10% combination level. By the discussions and results at this study, the significant conclusions of mechanical and physical properties were summarized as follows: 1. The MORs were shown in the order of 3 layer> 2 layer> 1 layer among plastic non-combined boards, and $T_3$ < $T_2$ < $T_1$ < RP (NP(5%) < NP(l0%) among plastic combined boards. In 2cm long plastic chip in 1 layer board, the highest strength through all the composition was recognized. 1 layer board showing the lower strength with 0.5cm plastic chip rendered to the bending strength improvement by 2 or 3 layer board composition. On the other hand, 2 or 3 layer combined with 1, 2cm long polypropylene net fiber chips incurred MOR's conspicuous decrease requiring optimum plastic chip combined level and consideration to combined type. 2. MOE in plastic non-combined 3 layer board exhibited sandwich construction effect by higher resin content application to surface layer in the order of 3layer>1layer>2layer with the highest stiffness of the board combined with polypropylene chip, while nylon chip-combined board had little difference from plastic non-combined board. In relevant to length and layer effect, 3 layer board combined with the 0.5cm long polypropylene net fiber chip in 5% and 10% combined level presented 34-43% and 44-76% stiffness increase against plastic non-combined board(control), respectively. Moreover, in 1 layer board, 30% stiffness increase with 10% against 5% combined level in the 1 and 2cm long polypropylene net fiber chip was obtained. 3. Stress at proportional limit(Spl) showing the fiber relationship (r: 0.81-0.97) between MOR presented in the order of 1 layer<2 layer<3 layer in plastic non-combined board. Correspondingly, combined effect by layer and plastic chip length was similar to MOR's. 4. Differently from previous properties(MOR, MOE, Spl). work to maximum load(Wml) of 2 layer board approached to that of 3 layer board. Conforming the above phenomenon. 2 layer combined with 0.5cm long polypropylene net fiber chip kept the greater work than 1 layer. The polypropylene combined board superior to nylon -and plastic non - combined board seemed to have greater anti - failing capacity. 5. Internal bond strength(IB), in contrast to MOR's tendency. showed in the order of T1

• Journal of the Korean Wood Science and Technology
• /
• 제29권3호
• /
• pp.47-58
• /
• 2001

For finding both ways of recycling the wood and plastic wastes and solving the problem of free formaldehyde gas emission through manufacturing wood particle-polypropylene fiber composite board without addition of formaldehyde-based thermosetting resin adhesive, control particleboards and nonwoven web composite boards from wood particle and polypropylene fiber formulation of 50 : 50, 60 : 40, and 70 : 30 were manufactured at density levels of 0.5, 0.6, 0.7, and 0.8 g/$cm^3$, and were tested both in the physical and mechanical properties according to ASTM D 1037-93. In the physical properties, control particleboard had significantly higher moisture content than composite board. In composite board, moisture content decreased with the increase of target density only in the board with higher content of polypropylene fiber and also appeared to increase with the increase of wood particle content at a given target density. Control particleboard showed significantly greater water absorption than composite board and its water absorption decreased with the increase of target density. In composite board, water absorption decreased with the increase of target density at a given formulation but increased with the increase of wood particle content at a given target density. After 2 and 24 hours immersion, control particleboard was significantly higher in thickness swelling than composite board and its thickness swelling increased with the increase of target density. In composite board, thickness swelling did not vary significantly with the target density at a given formulation but its thickness swelling increased as wood particle content increased at a given target density. Static bending MOR and MOE under dry and wet conditions increased with the increase of target density at a given formulation of wood particle and polypropylene fiber. Especially, the MOR and MOE under wet condition were considerably larger in composite board than in control particleboard. In general, composite board showed superior bending strength properties to control particleboard, And the composite board made from wood particle and polypropylene fiber formulation of 50 : 50 at target density of 0.8 g/$cm^3$ exhibited the greatest bending strength properties. Though problems in uniform mixing and strong binding of wood particle with polypropylene fiber are unavoidable due to their extremely different shape and polarity, wood particle-polypropylene fiber composite boards with higher performance, as a potential substitute for the commercial particleboards, could be made just by controlling processing variables.

• 대한토목학회논문집
• /
• 제34권6호
• /
• pp.1677-1685
• /
• 2014

섬유를 콘크리트의 보강재로 소량 혼입한 섬유 보강 콘크리트는 콘크리트의 인장저항 능력과 연성능력을 향상시킬 수 있다. 최근에는 강섬유의 적용성이 확대됨에 따라 강섬유 길이의 연장을 통해 보강의 효과를 증대시키고 있다. 섬유의 길이 연장은 동일한 시공성과 품질성을 위해 섬유 혼입률을 동시에 감소시킬 필요가 있다. 따라서, 본 연구에서는 35mm, 60mm 길이의 강섬유와 화학적인 안정성과 내구성, 경제성 등이 우수한 보강 재료로 평가되어지고 있는 폴리프로필렌 섬유에 대해 섬유혼입률 1.0% 이하에서의 휨 성능을 평가하였다. 강섬유 혼입률이 0.25% 이상, 폴리프로필렌 섬유는 혼입률 0.5% 이상에서 균열강도 도달 후 취성 파괴되는 무보강보의 파괴거동을 개선하는 효과가 나타났다. 다만, 폴리프로필렌 섬유가 혼입된 보강 콘크리트는 균열 이후 deflection-softening 거동을 보였다. 그러나, 0.5%이상의 폴리프로필렌이 혼입된 보강보는 균열 이후 최대강도가 균열강도의 약 60~80%정도 강도회복을 보였으며, 강섬유에 비해 균열 이후 응력감소현상을 지연시키는 경향이 뛰어난 것으로 판단된다. 결론적으로 폴리프로필렌 보강콘크리트는 0.75% 혼입률 이상에서는 충분히 만족할 만한 구조적 휨 성능 향상을 보일 수 있을 것으로 판단된다. 특히, 폴리프로필렌 1.0% 보강 콘크리트의 에너지 흡수 성능은 0.5%, 0.75%가 혼입된 강섬유 보강 콘크리트의 에너지 흡수성능과 거의 비슷한 것으로 평가되었다.

• 소성∙가공
• /
• 제25권6호
• /
• pp.402-408
• /
• 2016

A manufacturing technology of carbon fiber composites with thermoplastic polymer pellets and continuous woven fiber was investigated using a compression molding process. To secure the impregnation of resin into the porosity of fabric the composite specimens were prepared with general injection-molding grade polypropylene pellets and low viscosity polycarbonate pellets. Tensile tests of polypropylene and polycarbonate composites were performed. Polycarbonate composites showed higher fracture strength than that of polypropylene composites because of the difference of matrix properties. However, the increase rate of strength was lower than that of polypropylene composites due to the difference of coherence between matrix and reinforcement. To investigate the effect of carbon fiber volume fraction on the fracture strength variation polypropylene composites with different volume fraction were compression molded and tensile tests were performed together. It was shown that the fracture strength of the polypropylene composites increased by 3.2, 5.4 and 6.9 times with the increase of carbon fabric volume fraction of 0.256, 0.367, and 0.480, respectively.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.115-118
• /
• 1999

Tensile behavior of polypropylene fiber reinforced concrete due to restrained shrinkage has been investigated experimentally by ring and beam tests. Parameters include types of concrete, water-cement ratio, volume fraction of fiber and steel ratio. Results show that little influence of the addition of polypropylene(Vf=0.1%) has been observed as expected and results from other researches.

• 한국농공학회논문집
• /
• 제46권6호
• /
• pp.13-19
• /
• 2004

This study was performed to evaluate permeable properties of eco-concrete using soil, natural coarse aggregate, soil compound and polypropylene fiber. The fIexural strength, ultrasonic pulse velocity and dynamic modulus of elasticity were increased with increasing the content of coarse aggregate, soil compound and polypropylene fiber. The flexural strength, ultrasonic pulse velocity and dynamic modulus of elasticity were 259 MPa, 3,527 m/s and 275 ${\times}$ 102 MPa at the curing age of 28 days, respectively. The coefficient of permeability was decreased with increasing the content of coarse aggregate and soil compound, but it was increased with increasing the content of polypropylene fiber. Accordingly, this concrete can be used for farm road.

• 한국재료학회지
• /
• 제15권8호
• /
• pp.521-527
• /
• 2005

Surface modification of polypropylene hollow fiber membranes was peformed in order to develop blood-compatible biomaterials for use in the blood contacting and oxygenation membranes of a lung-assist device(LAD). Blood compatibility was determined by using anticoagulation blood and evaluating formation of blood clots on their surfaces as well as activation of plasma coagulation cascade, platelet adhesion, and aggregation. It was verified that the number of platelets on the silicone coated fibers was significantly lower than those on polypropylene. It was also found that the polypropylene hollow fiber membranes using plasma treatment exhibited suppression of complement activation in blood compatibility test.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.33-36
• /
• 2006

The purpose of this paper is to investigate the structural behavior of fire damaged high-strength SRC columns with polypropylene fiber. When high-strength concrete is exposed to high temperature, spalling is occurred then it leads to decrease the capacity of members. Polypropylene fiber is used to reduce the spalling of the specimens and the distinction in the behavior after fire is observed. High-strength concrete specimens were exposed to high temperatures by the ISO 834 curve. Main experimental parameters were the ratio of the contained polypropylene fiver, heating time and type of loading. Reduction rate in residual strength and stiffness is observed for the mixing of PP fiber, the heating time and eccentricity of loading.