• Journal of Environmental Science International
• /
• v.9 no.6
• /
• pp.511-515
• /
• 2000

The purpose of this experiment is to prepare ethylene propylene diene terpolymer(EPDM)/ acrylonitrile butadiene rubber(NBR) blend which represents good environmental resistant properties including favorable oil and ozone resistance. With incorporation of EPDM, NBR and other ingredients, the rubber and chemical additives were mixed by mechanical method such as Banbury mixer and open 2-roll mill. Then rubber vulcanizates were manufactured by hot press and mechanical properties, oil and ozone resistance of the test specimens were measured. The oil resistance and ozone resistance of EPDM and NBR, respectively, is remarkably improved by blending EPDM with NBR. The optimum results of oil and zone resistant characteristics were obtained at EPDM/NBR(=25/75 wt%) composition ratio.

• Journal of the Korean Ceramic Society
• /
• v.34 no.4
• /
• pp.394-398
• /
• 1997

Mn-Zn ferrite powders were prepared by alcoholic dehydration, using coprecipitation method. Then the effects of organic dispersant and polymeric binder concentration on stability and casting of slurry were discussed. Citric acid, the organic dispersant and polyvinylacohol(PVA), the non-ionic binder, were selected as additives of slurry. With variation of concentration of water, citric acid and polyvinylalcohol(PVA), optimum forming conditions were determined from viscosity and density. To compare with dry process, density and microstructure of sintered body formed by uniaxial die pressing were observed.

• Applied Chemistry for Engineering
• /
• v.7 no.3
• /
• pp.588-596
• /
• 1996

The optimum conditions of the 1st and 2nd distillation had been investigated to obtaine a high quality monomeric MDI and fire reactive polymeric MDI by purification of crude MDI. Effect of additives on the monomeric MDI's color change, dimerization and the reactivity of polymeric MDI with standard polyol system has been tested. When the monomeric MDI yield is approximately 32%, 4,4'-MDI content is above 98% in the monomeric MDI at the 1st distillation. When the separation ratio of initial portion and residue percentage, reflux ratio are set at respectively, approximately 20wt%, 9wt%, above 2 in order to minimize the content of 2,4'-MDI in monomeric MDI, the freezing point of final distilled monomeric MDI is above $38.4^{\circ}C$. Since the monomeric MDI is inherently unstable in the room condition, monomeric MDI easily changes it's color and conducts self-polymerization reaction. To increase the stability of monomeric MDI, the composition of antioxidant, which is composed of phenolic 1st antioxidant, phosphorus 2nd antioxidant, UV absorbent and Hindered amine light stabilizer are used, and benzoyl chloride as antipolymerization agent test are that APHA color is less than 20, dimer content is remained less than 0.36wt% after 45 days storage of monomeric MDI.

• Membrane Journal
• /
• v.34 no.3
• /
• pp.192-203
• /
• 2024

The advancement of commercially viable gas separation membranes plays a pivotal role in improving CO₂ separation efficiency. High-molecular-weight poly(ethylene oxide) (high-Mw PEO) emerges as a promising option due to its high CO₂ solubility, affordability, and robust mechanical attributes. However, the crystalline nature of high-Mw PEO hinders its application in gas separation membranes. This study proposes a straightforward blending approach by incorporating various polymeric additives into high-Mw PEO to address this challenge. Four commercially available, water-soluble polymers, i.e. poly(ethylene glycol) (PEG), poly(propylene glycol) (PPG), poly(acrylic acid) (PAA), and poly(vinyl pyrrolidone) (PVP) are examined as additives to enhance membrane performance by improving miscibility and reducing PEO crystallinity. Contrary to expectations, PEG and PPG fail to inhibit the crystalline structure of PEO and result in membrane flaws. Conversely, PAA and PVP demonstrate greater success in altering the crystal structure of PEO, yielding defect-free membranes. A thorough investigation delves into the correlation between changes in the crystalline structure of high-Mw PEO blend membranes and their gas separation performance. Drawing from our findings and previously documented outcomes, we offer insights into designing and selecting additive polymers for high-Mw PEO, aiming at the creation of cost-effective, commercially viable CO₂ separation membranes.

• Clean Technology
• /
• v.8 no.4
• /
• pp.173-180
• /
• 2002

As a primary material for MLCC, $BaTiO_3$ particles coated with two additives in a core-shell structure were prepared in this study. This composite powder can not only reduce the VOC emission during MLCC manufacture but also increase the density and reliability of electronic products. The additives were $Y_2O_3$ and $MnCO_3$, whose composition information was obtained from domestic companies. It was observed that the surface of $BaTiO_3$ particles was uniformly as well as simultaneously coated by those two materials via urea-decomposition reaction over $70^{\circ}C$ as the reaction temperature. Elemental analysis indicated that the measured content of each additve was quite close to the designated value. The effect of polymeric dispersant such as PVP, on the coating characteristics was not as significant as expected.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.3
• /
• pp.129-134
• /
• 2018

Herein, we report the manufacture of high-performance, ambipolar organic field-effect transistors (OFETs) and complementary-like electronic circuitry based on a blended, polymeric, semiconducting film. Relatively high and well-balanced electron and hole mobilities were achieved by incorporating a small amount of ionic additives. The equivalent P-channel and N-channel properties of the ambipolar OFETs enabled the manufacture of complementary-like inverter circuits with a near-ideal switching point, high gain, and good noise margins, via a simple blanket spin-coating process with no additional patterning of each active P-type and N-type semiconductor layer.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06a
• /
• pp.1-18
• /
• 2006

A novel transmission electron microscopy technique for the visualization of polymers adsorbed on secondary fines has been developed. This technique has been utilized in observing the adsorption behavior of various wet-end additives. The technique is sensitive enough not only to allow differentiation between linear and branched polymers, but also to observe differences in the adsorption behavior and conformational characteristics of particular polymeric derivatives. Conformational changes of a cationic polyacrylamide (CPAM) were examined in response to variations in wet-end conditions, such as mixing time and system conductivity. The molecular conformations of cationic starch and cationic guar gum were also examined by this technique. The technique has been employed to observe the effects of silica microparticles on the conformational characteristics of CPAM (drainage/retention aid) pre-adsorbed on secondary fines. The transmission electron microscopy method is a viable tool for investigating the macromolecular events that make up a large part of wet end chemistry in papermaking.

• Tribology and Lubricants
• /
• v.15 no.4
• /
• pp.343-353
• /
• 1999

The role of viscosity index improver's(Ⅶ) additives for modem engine lubrication is complex. Under the condition of atmosphere or low shear rate, the characteristics of Ⅶ added lubricant is verified and quoted frequently for mathematical model of lubricant behavior. However, recent research shows that added lubricant has the characteristics of shear thinning at high shear rate condition although it performs well enough over the whole range of working temperature. At high shear rate, they show significant decrease of apparent viscosity irrespective of temperature. Many experimental researches verify that Ⅶ added lubricant shows boundary film layer formation on the solid surface as well as shear thinning effect by its polymeric molecular characteristics. The intend of our research is to verify the effects of Ⅶ from the viewpoint of continuum mechanics, because conventional Reynolds'equation with only pressure-viscosity relation cannot fully predict the lubricant behavior under the Ⅶ added condition. In these aspects, Reynolds'equation of Newtonian fluid model lacks the reflection of real fluid behavior and there is no way to explain the non-linear characteristics of Ⅶ added lubricant. In this research, we mathematically modeled the Ⅶ added lubricant behaviors which are the characteristics of non-Newtonian fluid behavior at high shear rate and boundary film formation on the solid surface. The consideration of elastic deformation in the contact region is also included in our computation and finally the converged film pressure and the film thickness with elastic deformation are obtained. The results are compared with those of Newtonian fluid model.

• Korean Chemical Engineering Research
• /
• v.53 no.3
• /
• pp.382-390
• /
• 2015

Poly(methyl methacrylate) (PMMA) supports and amine additives were investigated to adsorb $CO_2$. PMMA supports were fabricated by using different ratio of pore forming agents (porogen) to control the BET specific surface area, pore volume and distribution. Toluene and xylene are used for porogens. Supported amine sorbents were prepared by wet impregnation of tetraethylenepentamine (TEPA) on PMMA supports. So we could identify the effect of the pore structure of supports and the quantity of impregnated TEPA on the adsorption capacity. The increased amount of toluene as pore foaming agent resulted in the decreased average pore diameter and the increased BET surface area. Polymer supports with huge different pore distribution could be fabricated by controlling the ratio of porogen. After impregnation, the support with micropore structure is supposed the pore blocking and filling effect so that it has low $CO_2$ capacity and kinetics due to the difficulty of diffusing. Macropore structure indicates fast adsorption capacity and low influence of amine loading. In case of support with mesopore, it has high performance of adsorption capacity and kinetics. So high surface area and meso-/macro- pore structure is suitable for $CO_2$ capture.

• Elastomers and Composites
• /
• v.44 no.3
• /
• pp.222-231
• /
• 2009

Shirasu-porous-glass (SPG) membrane emulsification is highly attractive in the field of toner industries, foods and drug delivery systems because of its easy control of particle size in micro-scale, narrow size distribution and multiple emulsion. The particle size and morphology of emulsion droplets can be controlled by changing the type of initiators, additives, monomers, crosslinkers and inhibitors in SPG membrane emulsification. In this paper, principles of SPG membrane emulsification, influence of process parameters and industrial applications have been addressed.