• Journal of the Korea Concrete Institute
• /
• v.13 no.4
• /
• pp.406-413
• /
• 2001

Up to this day, reinforced spun concrete pipes have been widely used as drain pipes. However, many reinforced spun concrete pipes are exposed to the deteriorated environment such as freezing-thawing damage and chemical attack by the growth of a sulfur-oxidizing bacterium isolated from corroded concrete. The purpose of this study is to evaluate the effects of lining by polymer-modified mortar using polymer dispersions as cement modifier on the development in durability of reinforced spun concrete pipe. The polymer-modified mortars were prepared with various polymer types and polymer-cement ratios, and tested for compressive and flexural strengths, acid, freezing-thawing, and heat resistances. And then, the reinforced spun concrete pipe product lined by polymer-modified mortars was tested for adhesion in tension and surface conditions according to curing temperatures in the field. From the test results, it is apparent that the polymer-modified mortars have good mechanical properties and durability as a lining material. In practice, all polymers can be used as lining the materials for reinforced spun concrete pipe, and types of polymer, and polymer-cement ratio and curing conditions are controlled for a good lining product.

• Journal of the Korea Concrete Institute
• /
• v.15 no.6
• /
• pp.888-893
• /
• 2003

The purpose of this study is to make clear the durability of the polymer films formed in the autoclaved polymer-modified mortars and concretes. The polymer films prepared with polymer dispersions such as a styrene-butadiene rubber (SBR) latex, a poly (ethylene-vinyl acetate)(EVA) emulsion and a polyacrylic ester (PAE) emulsion for polymeric admixtures are exposed to autoclaving at 18$0^{\circ}C$ in temperature and 1.01 MPa in vapor pressure, and subjected to tensile test and infrared spectroscopy. The durability of the polymer films is evaluated from the application of autoclaving to the polymer films under saturated Ca(OH)$_2$ solution immersion causes no degradation for SBR films and a significant degradation due to the saponification of the polymers for EVA and PAE films. Accordingly, in the application of autoclaving to polymer-modified mortars and concretes, it is suggested that SBR-modified mortars and concretes are hardly degraded but EVA- and PAE-modified mortars and concretes are markedly degraded by the saponification of the polymers.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.88-97
• /
• 2002

The effect of aminosiloxane modifier on the chemorheological properties of ortho-cresol novolac epoxy/phenol novelac/triphnylphosphine resin system was investigated aat different isothermal curing temperatures. By adding the aminosiloxane to the resin system, not only conversion rate and conversion were increased but also glass transition temperature was promoted. Critical conversion and gelation time obtained at the crossover point between storage and loss moduli were reduced and thus the viscosity was increased by the aminosiloxane. $C_1$ and $C_2$ in the WLF equation calculated from the glass transition temperature as a function of conversion and measured viscosity were found to vary with the curing temperature. By applying the change of glass transition temperature with conversion, $C_1$ and $C_2$ to WLF equation, it was possible to predict accurately the viscosity change with isothermal curing reaction.

• Elastomers and Composites
• /
• v.57 no.3
• /
• pp.107-113
• /
• 2022

The effects of fillers [talc, calcium carbonate, glass fiber, and EBR (ethylene-butene rubber)] on the shrinkage and mechanical properties of injection-molded polypropylene composites were investigated. The shrinkage correlated with the shape of the filler particles: at the same amount added, glass fibers with a large aspect ratio had the greatest effect on the shrinkage of polypropylene composites, followed by flake-shaped talc and granular calcium carbonate. It was confirmed that the addition of EBR rubber as an impact strength modifier reduced shrinkage proportionally to the added content. In addition, the addition of glass fiber resulted in the greatest increases in tensile and flexural strengths.

• Elastomers and Composites
• /
• v.57 no.4
• /
• pp.222-230
• /
• 2022

In this study, a low-heat additive with a crosslink structure was dispersed in asphalt to simultaneously lower the production temperature of, and to modify the asphalt binder. This low-heat additive was prepared by different feeding ratios of styrene-butadiene-styrene (SBS) and polyvinylchloride (PVC) as polymer modifiers, and ZnO as a crosslinking agent. In order to confirm the crosslinking density and compatibility of the crosslink structured low-heat additive with asphalt, surface free energy, swelling ratio, differential scanning calorimetry (DSC), and scanning electron microscope (SEM) parameters were carefully investigated to examine this relationship, and the role of the crosslink structured low-heat additive. In addition, by measuring the penetration and softening point of the asphalt binder, it was confirmed that it corresponds to PG 64-22. With increasing ZnO in the crosslink structured low-heat additive, the swelling ratio decreased, leading to an increase in crosslinking density. The crosslink structured low-heat additive and the asphalt binder were found to be compatible with each other by DSC and SEM analysis.

• Elastomers and Composites
• /
• v.43 no.3
• /
• pp.191-198
• /
• 2008

It is said that polymer modified asphalt using polyethylene as modifier would show phase separation due to density difference and incompatibility between asphalt and polyethylene. In this study, to prevent coalescence of polyethylene in asphalt, we employed peroxides as phase separation inhibitor. On microscope, peroxides (dicumyl peroxide, lauroyl peroxide) with waste vinyl (comprising low density polyethylene) did not show phase separation, however, rheometer test showed phase separation at molecular level, i.e., polyethylene and asphalt are immiscible ultimately. Mechanical properties (tensile strength, Marshall stability, dynamic stability) showed waste vinyl-modified asphalts are highly resistant to plastic deformation and these properties are even better than those of Superphalt.

• Applied Chemistry for Engineering
• /
• v.7 no.4
• /
• pp.679-690
• /
• 1996

Acrylic copolymer was synthesized from 2-dimethylaminoethyl methacrylate and alkylmethacrylate containing long chain hydrocarbon group. To facilitate emulsification in water, acrylic copolymer was treated with acetic acid, and therefore acetated acrylic copolymer was produced. Acetated acrylic copolymer was perfectly emulsified in water and showed increased emulsion stability. Polymer as a cement dispersion agent(PDCM-PSD) was prepared by blending the newly synthesized acetates acrylic copolymer with sodium gluconate, oleic acid, and triethanolamine. The applicability of the blended polymer was examined, and it was found that the effects of dispersion and water-proof(0.3~0.5) were excellent.

• Polymer(Korea)
• /
• v.31 no.1
• /
• pp.68-73
• /
• 2007

This study is on the synthesis of reactive polymer modifiers by emulsion polymerization to improve properties of asphalt for paving. Styrene, methyl methacrylate (MMA), isoprene and glycidyl methacrylate (GMA) which has epoxy ring to react with carboxyl group of asphaltene were used to synthesize polymer modifiers. Modifiers with various composition were tested miscibility with asphalt. Modifiers which showed good miscibility with asphalt were investigated by DSC for $T_g$. Existence of epoxy rings and their reaction with asphaltene wore investigated by FTIR. Molecular structures of synthesized modifiers were confirmed by $^1H-NMR$. The synthesized modifiers which showed good miscibility had their $Tg's$ in the range of $37.5{\sim}56.5^{\circ}C$ and had isoprene contents of 30 wt%. They showed good miscibility in the 1 and 2 wt% concentrations, but not in the 3 wt% concentration.

• Polymer(Korea)
• /
• v.36 no.3
• /
• pp.287-294
• /
• 2012

ZnAl-LDH(layered double hydroxide) (Zn:Al=2:1 mole ratio) modified with stearic acid (SA) or oleic acid (OA) was synthesized by a coprecipitation method and compounded to SAN polymer at various contents. All the SAN composites were manufactured by a co-rotating twin-screw extruder and subsequently injection molded into several specimen. Morphology, transparency, and thermal resistance of these composites were evaluated by TEM, XRD(X-ray diffractometry), UV-Vis spectrophotometry, and thermogravimetric analysis. SAN nanocomposites containing OA-$Zn_2Al$ LDH showed better optical transmittance than SAN nanocomposites containing SA-$Zn_2Al$ LDH. All the SAN nanocomposites containing OA-$Zn_2Al$ LDH or SA-$Zn_2Al$ LDH exhibited improvement of thermal resistance at second stage of thermal oxidation. These results were explained by the fact that the interaction between organic modifier and polymer performed an important role in the property improvement of polymer nanocomposites.

• Applied Chemistry for Engineering
• /
• v.24 no.1
• /
• pp.104-111
• /
• 2013

Poymer blends of two degradable aliphatic polyesters, relatively expensive material polylactic acid (PLA) and relatively inexpensive material poly(butylene adipate-co-terephthalate) (PBAT), were used in this study. Three different kinds of modifiers were used with various amounts. Diisocyanate type methylenediphenyl 4,4'-diisocyanate (MDI) and hexamethylene diisocyanate (HDI) were used as modifiers and epoxy type coupling agents also used. The melt flow index (MFI) and dynamic viscoelasticity of various compositions of PLA/PBAT blends were studied. The mechanical property and morphology with respect to the fracture surface of PLA/PBAT blends were also investigated using tensile test and field emission scanning electronic microscopy, respectively. These tests were also used to verify the compatibility of PLA/PBAT and the effect of mechanical properties due to the use of modifiers. Tensile properties of PLA/PBAT blends modified with HDI were improved remarkably.