• Bulletin of the Korean Chemical Society
• /
• v.7 no.2
• /
• pp.137-142
• /
• 1986

The luminescence spectra of $Ru(bpy)_3^{2+}$ in poly(methacrylic acid) (PMA) solutions varied sensitively with pH. At pH < 5.5, the emission intensity increased with pH up to 4 times, while it decreased with pH beyond the pH. The enhanced emission intensity was accompanied by blue-shift of the emission maxima as much as 15 nm. The enhancement of emission intensity was attributed to the restricted rotational mobility of ligand of the cation bound to densely coiled PMA molecules at pH < 5.5. The sharp decrease in emission intensity with increasing pH near pH 5.6 was accounted for conformational transition of the polymer to more extended structure, which was also revealed in viscosity measurement. The enhancement of emission intensity became higher as NaCl concentration of the solution increased. The binding constant of $Ru(bpy)_3^{2+}$ with two carboxylate groups of PMA was calculated as $2{\times}10^5\;M^{-1}$ in 0.1 M NaCl at pH 5.2. The pH dependence of luminescence quenching rate of $Ru(bpy)_3^{2+}$ by $Cu^{++}$ also showed maximum near pH 5, and the rate was more than $10^3$ times higher than that in water, whereas the maximum enhancement of quenching rate (about 20 times) in poly(acrylic acid) (PAA) solution occurred at pH 4.5. On the other hand, the pH dependence for neutral water soluble nitrobenzene (NB) exhibited opposite trend to that of $Cu^{++}$. The quenching constant vs pH curve for $MV^{++}$ was composite of those for $Cu^{++}$ and NB. The anomalous high quenching rate for $Cu^{++}$ in PMA solution at pH < 5.5 was attributed to the binding of $Ru(bpy)_3^{2+}$ and $Cu^{++}$ to the same region of PMA, when it conforms densely coiled structure in the pH range. The observation of mininium quenching rate for NB near pH 5.5 indicated that the $Ru(bpy)_3^{2+}$ bound to the densely coiled PMA is not accessible by NB, which is in bulk water phase. The composite nature of the pH dependence of quenching rate for $MV^{++}$ in PMA solution was attributed to the smaller binding affinity of the cation to PMA, compared to that of $Cu^{++}$. The sharp, cooperative conformational transition with pH observed in PMA was not revealed in PAA. But, the pH dependence of quenching rates in this polymer reflected increased charge density and, thus, binding of cations to the polymer, and expansion of the polymer chain with pH.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.4
• /
• pp.545-560
• /
• 2019

During EPB TBM tunnelling, an appropriate application of additives such as foam and polymer is an essential factor to secure the stability of TBM as well as tunnelling performance. From the '90s, there have been many studies on the optimal injection of additives worldwidely contrary to the domestic situation. Therefore, in this paper, the foam, which is widely adopted for soil conditioning, was selected as an additive in order to investigate the effect of foam injection on TBM performance through a series of laboratory excavation tests. The excavation experiments were carried out on artificial sandy soil specimens with consideration of the variance of FIR (Foam Injection Ratio), FER (Foam Expansion Ratio) and $C_f$ (Surfactant Concentration), which indicate the amount and quality of the foam. During the tests, torque values were measured, and the workability of conditioned soil was evaluated by comparing the slump values of muck after each experiment. In addition, a weight loss of the replaceable aluminum cutter bits installed on the blade was measured to estimate the degree of abrasion. Finally, the foam injection ratio for the optimal TBM excavation for the typical soil specimen was determined by comparing the measured torque, slump value and abrasion. Note that the foam injection conditions satisfying the appropriate level of machine load, mechanical wear and workability are essential in the EPB TBM operational design.

• International Journal of Automotive Technology
• /
• v.7 no.5
• /
• pp.571-577
• /
• 2006

This paper deals with dynamic tensile characteristics for the polypropylene used in an IP(Instrument Panel). The polypropylene is adopted in the dash board of a car, especially PAB(Passenger Air Bag) module. Its dynamic tensile characteristics are important because the PAB module undergoes high speed deformation during the airbag expansion. Since the operating temperature of a car varies from $-40^{\circ}C$ to $90^{\circ}C$ according to the specification, the dynamic tensile tests are performed at a low temperature($-30^{\circ}C$), the room temperature($21^{\circ}C$) and a high temperature($85^{\circ}C$). The tensile tests are carried out at strain rates of six intervals ranged from 0.001/sec to 100/sec in order to obtain the strain rate sensitivity. The flow stress decreases at the high temperature while the strain rate sensitivity increases. Tensile tests of polymers are rather tricky since polymer does not elongate uniformly right after the onset of yielding unlike the conventional steel. A new method is suggested to obtain the stress-strain curve accurately. A true stress-strain curve was estimated from modification of the nominal stress-strain curves obtained from the experiment. The modification was carried out with the help of an optimization scheme accompanied with finite element analysis of the tensile test with a special specimen. The optimization method provided excellent true stress-strain curves by enforcing the load response coincident with the experimental result. The material properties obtained from this paper will be useful to simulate the airbag expansion at the normal and harsh operating conditions.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.2
• /
• pp.278-285
• /
• 2012

Effects of ion species on the expansion behavior of Poly(styrene sufonic acid)(PSSA) hydrogel were investigated in aqueous solution of selected anions, cations and hydrophobic ions. The deexpansion extent of Poly(stylene sulfonic acid) gel follow the sequence $SCN^-$<$Br^-$<$Cl^-$<$F^-$ in low concentration solutions due to the destabilization of anions to hydrogen bond between ${SO_3}^-$ and water. The deexpansion in cations followed the sequence of counterion interactions between ${SO_3}^-$ and cations. It was discussed the effects of ions on the hydrogen bonding through ${SO_3}^-$ and phenyl ring in salt solutions. Other interactions, such as the cation-${\pi}$ interaction, hydrophobic interaction, and dispersion force, contributed to the ion specific swelling of PSSA hydrogel.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.3.1-3.1
• /
• 2009

Normal sintering process of producing porous ceramics is not to sinter perfectly, i.e., stop sintering in middle-process. Our porous ceramic materials are a product of complete sintering. For example if one want to make a porous carborundum, raw carborundum powder is sintered at either lower temperatures than normal sintering temperature or shorter sintering periods than normal sintering time to obtain incompletely sintered materials, i.e., porous carborundum. This implies normally sintered porous ceramic materials can mot be used in high vacuum conditions due to dust coming out from uncompleted sintering. We could produce completely sintered porous ceramic materials. For example, we can produce porous carborundum material by using carborundum particles bonded by glassy material. The properties of this material are similar to carborundum. We could make quasi-zero thermal expansion porous material by using carborundum and particles of negative thermal expansion materials bonded by the glassy material. We apply to sinter them also by microwave to sinter quickly. We also use HIP process to introduce closed pores. We could sinter them in large size to produce $2.5m{\times}2.5m$ ceramic plate to use as a precision plate for flat display industries. This flat ceramic plate is the world largest artificial ceramic plate. Precision plates are basic importance to any advanced electronic industries. The produced precision plate has lower density, lower thermal expansivity, higher or similar damping properties added extra properties such as vacuum vise, air sliding capacity. These plates are highly recommended to use in flat display industries. We could produce also cylindrical porous ceramics materials, which can applied to precision roller for polymer film precision motion for also electronic industries.

• Journal of the Korean Geosynthetics Society
• /
• v.16 no.2
• /
• pp.97-107
• /
• 2017

Recently, there have been a lot of incidents related to ground sinks in urban areas, but restoration work is complicated and inconvenience due to on-site control, and particularly, grouting and soil filling are generally applied as recovery measures, but when the grouting or the soil filling is carried out, material segregation phenomenon occurs in the ground or a lot of restoration amount is often required, depending on the state of sinks and the existence of groundwater under the ground and the soil can be lost due to the flow of the ground water, and thus the purpose of this study is to develop a pouch-type filler applied to a trenchless method for emergency reinforcement of the ground sinks with the aim of quick recovery of the ground sink in urban areas, and as a result, it was confirmed that compression strength and the expansion ratio were different according to the temperature of ground water and the compression strength and the expansion ratio could be controlled by mixing alumina powder.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.297.2-297.2
• /
• 2016

Photoacoustic generation of ultrasound is an effective approach for development of high-frequency and high-amplitude ultrasound transmitters. This requires an efficient energy converter from optical input to acoustic output. For such photoacoustic conversion, various light-absorbing materials have been used such as metallic coating, dye-doped polymer composite, and nanostructure composite. These transmitters absorb laser pulses with 5-10 ns widths for generation of tens-of-MHz frequency ultrasound. The short optical pulse leads to rapid heating of the irradiated region and therefore fast thermal expansion before significant heat diffusion occurs to the surrounding. In this purpose, nanocomposite thin films containing gold nanoparticles, carbon nanotubes (CNTs), or carbon nanofibers have been recently proposed for high optical absorption, efficient thermoacosutic transfer, and mechanical robustness. These properties are necessary to produce a high-amplitude ultrasonic output under a low-energy optical input. Here, we investigate carbon nanotube (CNT)-polydimethylsiloxane (PDMS) composite transmitters and their nanostructure-originated characteristics enabling extraordinary energy conversion. We explain a thermoelastic energy conversion mechanism within the nanocomposite and examine nanostructures by using a scanning electron microscopy. Then, we measure laser-induced damage threshold of the transmitters against pulsed laser ablation. Particularly, laser-induced damage threshold has been largely overlooked so far in the development of photoacoustic transmitters. Higher damage threshold means that transmitters can withstand optical irradiation with higher laser energy and produce higher pressure output proportional to such optical input. We discuss an optimal design of CNT-PDMS composite transmitter for high-amplitude pressure generation (e.g. focused ultrasound transmitter) useful for therapeutic applications. It is fabricated using a focal structure (spherically concave substrate) that is coated with a CNT-PDMS composite layer. We also introduce some application examples of the high-amplitude focused transmitter based on the CNT-PDMS composite film.

• Journal of Microbiology and Biotechnology
• /
• v.15 no.2
• /
• pp.259-264
• /
• 2005

Transplantation of cultured chondrocytes can regenerate cartilage tissues in cartilage defects in humans. However, this method requires a long culture period to expand chondrocytes to a large number of cells for transplantation. In addition, chondrocytes may dedifferentiate during long-term culture. These problems can potentially be overcome by the use of undifferentiated or partially developed cartilage precursor cells derived from neonatal cartilage, which, unlike chondrocytes from adult cartilage, have the capacity for rapid in vitro cell expansion and may retain their differentiated phenotype during long-term culture. The purpose of this study was to compare the cell growth rate and phenotypic modulation during in vitro culture between adult chondrocytes and neonatal chondrocytes, and to demonstrate the feasibility of regenerating cartilage tissues in vivo by transplantation of neonatal chondrocytes expanded in vitro and seeded onto polymer scaffolds. When cultured in vitro, chondrocytes isolated from neonatal (immediately postpartum, 2 h of age) rats exhibited much higher growth rate than chondrocytes isolated from adult rats. After 5 days of culture, more neonatal chondrocytes were in the differentiated state than adult chondrocytes. Cultured neonatal chondrocytes were seeded onto biodegradable polymer scaffolds and transplanted into athymic mice's subcutaneous sites. Four weeks after implantation, neonatal chondrocyte-seeded scaffolds formed white cartilaginous tissues. Histological analysis of the implants with hematoxylin and eosin showed mature and well-formed cartilage. Alcian blue/ safranin-O staining and Masson's trichrome staining indicated the presence of highly sulfated glycosarninoglycans and collagen, respectively, both of which are the major extracellular matrices of cartilage. Immunohistochemical analysis showed that the collagen was mainly type II, the major collagen type in cartilage. These results showed that neonatal chondrocytes have potential to be a cell source for cartilage tissue engineering.

• Polymer(Korea)
• /
• v.24 no.2
• /
• pp.201-210
• /
• 2000

To determine the effect of chain length of linear amine curing agents on the thermal and mechanical properties, standard epoxy resin, diglycidyl ether of bisphenol A (DGEBA) was cured with diethylenetriamine (DETA), triethylenetetraamine (TETA) and tetraethylenepentaamine (TEPA) in a stoichiometrically equivalent ratio. From this work, the effect of linear amine curing agents on the thermal and mechanical properties was significantly influenced by chain length of curing agents. In contrast, the results showed that the DGEBA/DETA system had higher values than the DGEBA/TETA and DGEBA/TEPA system in the density, shrinkage (%), thermal expansion coefficient, tensile modulus, and flexural strength. Whereas the DGEBA/DETA cure system had lower values than the DGEBA/TETA and DGEBA/TEPA cure system in the maximum exothermic temperature, conversion (%), and T$_{g}$. These findings imply that the differences in the maximum conversion about the chain length of curing agents affect the thermal and mechanical properties.s.

• Polymer(Korea)
• /
• v.25 no.2
• /
• pp.254-262
• /
• 2001

Epoxy resin based upon the N,N'-diglycidylaniline which is widely used in optic, electronic and composite material. We modified this epoxy resin with poly(amic acid) (PAA) that is a precursor of polyimide. To improve the mechanical property we controlled PAA content and imidization ratio. PI-modified epoxy blends were prepared for the formation of IPN structure. The possible reaction in the epoxy resin/PAA blends were investigated by FT-IR and inherent viscosity techniques. Thermal properties are measured by TGA, DSC, and TMA. Mechanical properties are measured by UTM and impact test machine. Morphology is investigated by SEM. Thermal stability improved with increasing the content of PAA in blends. As the content of PAA increases in blend, the glass transition temperature and thermal expansion coefficient decreases. Increasing impact strengths in J/m in the range of 920∼2412 were observed in blends. The PAA segment may act as a toughening agent in the epoxy networks, thus contributing the impact strength improvement of the blends.