• 한국도로학회논문집
• /
• 제17권2호
• /
• pp.21-30
• /
• 2015

PURPOSES : The purpose of this study was to evaluate the performance of rapid-setting polymer-modified asphalt mixtures with a high reclaimed asphalt pavement (RAP) content. METHODS: A literature review revealed that emulsified asphalt is actively used for cold-recycled pavement. First, two types of rapid-setting polymer-modified asphalt emulsion were prepared for application to high-RAP material with no virgin material content. The quick-setting polymer-modified asphalt mixtures using two types of rapid-setting polymer-modified asphalt emulsion were subjected to the following tests: 1) Marshall stability test, 2) water immersion stability test and 3) indirect tensile strength ratio test. RESULTS AND CONCLUSIONS : Additional re-calibration of the RAP was needed for laboratory verification because the results of analyzing RAP aggregates, which were collected from different job sites, did not deviate from the normal range. The Marshall stability of each type of binder under dry conditions was good. However, the Type B mixtures with bio-additives performed better in the water immersion stability test. Moreover, the overall results of the indirect tensile strength test of RAP mixtures with Type B emulsions exceeded 0.7. Further research, consisting of lab testing and on-site application, will be performed to verify the possibility of using RAP for minimizing the closing of roadways.

• 한국도로학회논문집
• /
• 제15권2호
• /
• pp.65-71
• /
• 2013

PURPOSES : The objective of this study is to evaluate the effect of physical characteristics of emulsion asphalt and aggregate on performance of chip seal pavements. METHODS : In order to evaluate the performance of chip seal materials, the sweep tests and Vialit Plate Shock tests were conducted on the mixtures with five emulsion asphalt binders and three aggregate types. The sweep tests was intended to investigate the change of bonding properties between emulsion asphalt and aggregate with curing time. The Vialit Plate Shock test was used to evaluate the bonding properties of chip seal materials at low temperatures. RESULTS : Results from sweep tests showed that polymer modified emulsion asphalt can reduce the curing time by 1.5 hour comparing with typical emulsion asphalt. It is also found that the Flakiness Index of aggregates and absorption rate of binder are the major factors affecting the bonding properties of chip seal materials. The Vialit Plate Shock test results showed that the average aggregate loss of CRS-2 is ten times higher than CRS-2P No.2 indicating that the use of polymer additives in emulsion asphalt can improve the performance of chip seal materials in low temperature region. CONCLUSIONS : The use of polymer in emulsion asphalt can decrease the curing time of chip seal materials and increase the bonding properties between aggregates and asphalt binder. It is also concluded that the lower Flakiness Index and absorption rate of aggregates can improve the performance of chip seal pavement.

• 펄프종이기술
• /
• 제38권5호
• /
• pp.24-30
• /
• 2006

This study was performed to characterize inverse emulsion type cationic polyacrylamide (PAM) and to compare with powder and salt dispersion type PAMs as a retention and drainage aid. Salt dispersion type PAM has defects of high amount of salt which increases conductivity of white water, low active polymer contents and relatively worse retention and drainage properties than others because of its low molecular weight. Powder type PAM has benefit of high active polymer contents and good retention and drainage properties, but defects of low dissolution speed and insoluble particle generation were observed. However, inverse emulsion type showed the best retention and drainage aids among them by controlling molecular weight and morphology easily and it had relatively higher active polymer contents and better solubility.

• 한국응용과학기술학회지
• /
• 제30권2호
• /
• pp.339-347
• /
• 2013

나노에멀젼은 서브마이크론 크기의 에멀젼으로 치료 약물의 전달을 향상시키는 약물 전달체로서 많은 연구가 진행되고 있다. 본 연구의 목표는 폴리머를 함유한 나노에멀젼의 안정성에 대한 연구이다. 고농도의 Carbopol 941, Aristoflex AVC, Aronbis M, Permulen TR 2 및 Aculyn 44를 함유한 나노에멀젼의 안정성은 마크로에멀젼과는 다르게 불안정하였다. 폴리머를 유화 전에 첨가하여 제조한 에멀젼이 유화 후 폴리머를 첨가하여 제조한 에멀젼에 비해 초기 입자 크기가 더 크게 형성되었다. 저 농도의 폴리머를 함유한 경우에도 폴리머를 함유하지 않은 나노에멀젼에 비해 안정성이 감소하였으나 그 정도는 고농도에 비해 적었다. 점도가 유사한 경우 안정성에 미치는 순서는 Aristoflex AVC < Carbopol 941 < Permulen TR2 < Carbopol 941 + Aculyn 44 < Aronbis M의 순서로 불안정하였다.

• Macromolecular Research
• /
• 제11권3호
• /
• pp.198-201
• /
• 2003

Aqueous emulsion of polyurethane (PU) ionomers were reinforced with hydrophobic nanosilica to give composites. The aqueous emulsion was stable and the particle size increased as the content of hydrophobic nanosilica was increased. The reinforcing effect of nanosilica in mechanical properties of these composites were examined by dynamic mechanical and tensile tests, and the Shore A hardness was measured. Enhanced thermal and water resistance and marginal reduction in transparency of these composites were observed compared with pristine polymer. These results were similar with those of our previous studies on waterborne PU/organoclay nanocomposites.

• 공업화학
• /
• 제3권4호
• /
• pp.614-619
• /
• 1992

Soft segment가 각각 ester 및 ether형 polyol로된 2종의 polyurethane(PU) ionomer를 emulsion 블렌딩하여, 블렌드의 분산점도, 및 emulsion cast film의 접촉각, 기계적 특성을 조성의 함수로 측정하였다. 블렌드의 기계물성은 혼합법칙으로부터 심한 scattering이나, negative deviation을 보였으며, 이는 ester 및 ether형 polyol간의 상용성의 결여에 기인하는 것으로 보았다. 접촉각 측정 결과로부터 유화입경이 작은 PPG PU 입자가 주로 도막표면층을 형성하는 것을 확인할 수 있었다.

• 청정기술
• /
• 제11권1호
• /
• pp.1-12
• /
• 2005

본 연구는 모노머로 메틸메타 아크릴레이트와 노말부틸 아크릴레이트를 사용하여 수용액상에서 반연속식 유화중합을 실시하여 안정성이 우수한 폴리머 시멘트용 아크릴계 폴리머 에멀젼을 제조하기 위해 최종 폴리머 에멀젼의 평균 입자크기 및 농도에 관한 계면활성제의 영향을 고찰하였다. 실험결과, 사용한 비이온 계면활성제에 관한 폴리머 에멀젼의 농도는 LE-50, NP-50 > CE-50, Tween 20 > TX-405 > Brij 35 순으로 최종 폴리머 응석에 기인하여 낮아졌으며, 평균 입자크기도 작아지는 경향을 나타내었다. 또한 LE형과 NP형 비이온 계면활성제는 친수성 체인의 길이(n)가 증가할 수 록 응석의 발생이 거의 없는 안정한 폴리머 에멀젼을 얻을 수 있었으며, n = 30이상의 체인에서 평균입자크기는 250 - 320 nm, 폴리머 농도는 수용액 기준으로 40 %를 얻을 수 있었다. 반응초기에 반응기에 투입 (Initial reactor charge)한 계면활성제 종류의 영향은 음이온 계면활성제인 SDS를 사용한 경우에는 사용량에 무관하게 폴리머 에멀젼의 농도는 거의 일정하였으나, 양이온 계면활성제인 CTAB와 반응형 계면활성제인 HN-100의 경우에는 폴리머 에멀젼 농도가 낮아지는 경향을 나타내었다. 반면에 평균 입자크기는 SDS < CTAB < HN-100 순으로 커지는 경향이었다.

• 폴리머
• /
• 제34권6호
• /
• pp.491-494
• /
• 2010

무유화 에멀젼 공중합법을 이용하여 180~200 nm의 지름을 가지는 단분산성 폴리(스티렌/디비닐벤젠/비닐 아세테이트) [poly(ST-co-DVB-co-VAc)] 고분자 나노입자를 합성하였으며, 제조된 단분산성 고분자 나노입자의 표면을 비누화반응을 통하여 개질하여 단분산성 폴리(스티렌/디비닐벤젠/비닐알코올) [poly(ST-co-DVB-co-VA)] 나노입자를 제조하였다. 합성된 입자를 반응염료와 반응시켜 적색과 청색 단분산성 폴리(스티렌/디비닐벤젠/비닐알코올) 나노입자를 제조하였으며, 입자의 형태, 분산성 및 표면전하를 전자현미경, 시차열분석기, UV/Vis 흡광기 및 제타 전하 측정장치를 이용하여 규명하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회 논문집(II)
• /
• pp.1121-1126
• /
• 2000

The purpose of this study is to clarify chemical resistance of polymer-cement slurry coated reinforcing bars. Polymer cement slurry coated reinforcing bars were showed the good state to the bending resistance, impact resistance, adhesive strength, but exact data of the chemical resistance do not exist. Through the experimental, it is to certify chemical resistance of polymer cement slurry coated reinforcing bars. In this study, polymer cement slurry coated reinforcing bars are prepared with two types of polymer, polymer-cement ratios of 50%, 100%, 150%, coating thickness, curing periods of 3, 7, 28days, and tested for chemical resistance as KS(Korea Standard). From the test results, chemical resistance of polymer cement slurry coated reinforcing bars used by acrylic and St/BA emulsion were showed excellent without concerned polymer-cement ratios, curing period except for 1% aqueous solution $H_2SO_4$. But polymer cement coated reinforcing bar used by acrylic emulsion is inferior to aqueous solution NaOH.

• 폴리머
• /
• 제34권4호
• /
• pp.306-312
• /
• 2010

Triphenylvinylsilane (TPVS) containing vinyl acetate (VAc), butyl acrylate (BA), and Nmethylolacrylamide (NMA) copolymers were prepared by emulsion polymerization. The polymerization was performed at $80^{\circ}C$ in the presence of auxiliary agents and ammonium peroxodisulfate (APS) as the initiator. Sodium dodecyl sulphate (SDS) and Arkupal N-300 were used as anionic and nonionic emulsifiers, respectively. The resulting copolymers were characterized by using Fourier transform infrared spectroscopy (FTIR), gel permeation chromatography (GPC), and dynamic light scattering (DLS). Thermal properties of the copolymers were studied by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The morphology of copolymers was also investigated by scanning electron microscopy (SEM) and then the effects of silicone concentrations on the properties of the TPVS-containing VAc-acrylic emulsion copolymers were discussed. The obtained copolymers have high solid content (50%) and can be used in weather resistant emulsion paints as a binder.