• Polymer(Korea)
• /
• v.24 no.2
• /
• pp.259-267
• /
• 2000

Gel polymer electrolytes were prepared from poly(vinylidene fluoride-co-hexafluoro propylene)[P(VdF-co-HFP)] that had higher mechanical properties as well as higher dielectric constant ($\varepsilon$=8~13) than other polymeric matrix. Mechanical properties and ionic conductivities have been investigated as a function of blend ratio of electrolyte solution and polymer matrix. Ethylene carbonate (EC)/${\gamma}$-butyrolactone (${\gamma}$-BL) and lithium triflate (LiCF$_3$SO$_3$) were used as solvent and salt, respectively. The mechanical properties such as tensile strength, tensile modulus, compression modulus, and dynamic shear modulus were evaluated. The highest ionic conductivity was 1.09$\times$10$^{-3}$ S/cm for PVH40 containing 28.6 wt% of P(VdF-co-HFP) at $25^{\circ}C$. Tensile strength, tensile modulus and compression modulus were increased with P(VdF-co-HFP) content and abruptly changed between PVH70 and PVH80. Dynamic shear moduli showed a typical gel behavior and changed with shear strain.

• Polymer(Korea)
• /
• v.35 no.2
• /
• pp.146-151
• /
• 2011

The physical properties of poly (ethylene 2,6-naphthalate) (PEN) copolymers were studied. PEN copolymers were synthesized successfully from the mixtures of ethylene glycol(EG), 1,3-propanediol (PD) and l,4-butanediol (BD) with 2,6-dimethyl naphthalene dicarboxylate. The results indicated that PEN copolymers showed an amorphous state when the content of BD(PD) in applied EG/BD(EG/PD) mixtures was less than 40% during the polycondensation. As a result, the lowering of thermal properties, orientation, and mechanical properties was found, however, the dimensional stability was improved. This is a promising result to apply the synthesized PEN copolymers as flexibles substrates.

• Korean Chemical Engineering Research
• /
• v.40 no.6
• /
• pp.703-708
• /
• 2002

High pressure phase behavior data for poly(propyl acrylate) and poly(propyl methacrylate) with supercritical $CO_2$, ethylene, propane, butane, propylene, 1-butene, dimethyl ether, and $CHClF_2$ were measured in the temperature range from $23^{\circ}C$ to $186^{\circ}C$ and at pressures up to 2,400 bar. The cloud point were obtained at dissolved pressure below 2,070, 1,400, 1,880, 450, 2,200, 250, and 150 bar for poly(propyl acrylate) in supercritical $CO_2$, ethylene, propane, propylene, butane, 1-buthen, and dimethyl ether, respectively. The temperature range is $23-175^{\circ}C$. The poly(propyl methacrylate) does not dissolve in $CO_2$ at temperature of $240^{\circ}C$ and pressure 2,900 bar. The poly(propyl methacrylate)-propane, poly(propyl methacrylate)-butane, poly(propyl methacrylate)-propylene, poly(propyl methacrylate)-1-butene, and poly(propyl methacrylate)-$CHClF_2$ systems were dissolved at the pressures less than 2,390 bar, below 2,100 bar, below 570 bar, below 310 bar, below 300 bar, and below 170 bar, respectively. The temperature range shows from 40 to $186^{\circ}C$. The phase behavior of between binary poly(propyl acrylate)-$CO_2$ and poly(propyl acrylate)-dimethyl ether system were measured from upper critical solution temperature region to lower critical solution temperature region with added dimethyl ether concentrations of 5, 15 and 50 wt%.

• Macromolecular Research
• /
• v.13 no.6
• /
• pp.499-505
• /
• 2005

Ordered mesoporous materials with a hydrothermally-stable, protozeolitic framework were prepared by exploring the direct conversion of inorganic species based on co-surfactant templating systems. To confer hydrothermal stability on the mesoporous aterials, the organic-inorganic hybrids were heat-treated in strongly basic media. Co-surfactant templating systems of cetyltrimethylammonium bromide [$C_{16}H_{13}(CH_{3})_{3}$NBr, CTAB] with 1,3,5-trim­ethylbenzene (TMB) or a nonionic block copolymer of poly(ethylene oxide )-b-poly(propylene oxide )-b-poly(ethyl­ene oxide) ($EO_{20}PO_{70}EO_{20}$) were employed to improve the hydrothermal stability of the organic-inorganic self-assembly during the solid rearrangement process of the inorganic species. The mesoscopic ordering of the pore structure and geometry was identified by X-ray diffraction, small angle neutron scattering and electron microscopy.

• Journal of Pharmaceutical Investigation
• /
• v.33 no.1
• /
• pp.45-49
• /
• 2003

The solubility and stability of ondansetron hydrochloride (OS) in various vehicles were determined. The effect of cyclodextrins (CD) on the solubility of OS in water was determined by equilibrium solubility method. The solubility of OS at $32^{\circ}C$ increased in the rank order of isopropyl myristate (IPM) < propylene glycol laurate (PGL) ${\ll}$ propylene glycol monolaurate < propylene glycol monocaprylate (PGMC) < poly(ethylene glycol) 400 < diethylene glycol mono ethyl ether (DGME) < ethanol < poly(ethylene glycol) 300 < water (36.1 mg/ml) ${\ll}$ propylene glycol (PG) (283 mg/ml). The addition of PG or DGME to non-aqueous vehicles such as IPM, PGL and PGMC markedly increased the solubility of OS. The addition of CDs in water increased the solubility. Apparent stability constant for the CD complexation with OS was calculated to be $25.5\;M^{-1}$ for $2-hydroxypropyl-{\beta}-CD\;(2HP{\beta}CD)$. Twenty mM ${\beta}-CD$, 69.4 mM sulfobutyl ether ${\beta}-CD$ and 115.4 mM $2HP{\beta}CD$ increased the aqueous solubilty of OS 1.27, 2.18 and 1.85 times, respectively. OS was stable in buffered aqueous solution (pH 5.0). However, OS was relatively unstable in non-aqueous vehicles in the order of PG

• Applied Chemistry for Engineering
• /
• v.9 no.3
• /
• pp.424-429
• /
• 1998

Cloud-point data at $230^{\circ}C$ and 1,800 bar are presented for two poly(ethylene-co-vinyl alcohol)(PEVA) copolymers[9.9mol% and 17.8mol% vinyl alcohol(VA)] in ethylene, propane, propylene, n-butane, 1-butene, dimethyl ether(DME), and chlorodifluromethane(CDFM). The static type experimental apparatus with a view cell has been used for the experiment at the high pressure and temperature. The pressure-temperature (P-T) loops of PEVA(9.9mol% VA) copolymer-DME mixtures are presented at copolymer concentrations of 1.4wt% to 20.0wt%. Also, we presented the phase behavior of PEVA(17.8mol% VA) copolymer-DME system at copolymer concentration of 1.9wt% to 6.8wt%. The cloud-point curves for the PEVA copolymers in dimethyl ether showed single phase above 480 bar as a result of the hydrogen bonding between the vinyl alcohol unit and dimethyl ether. The pressure-concentration(P-x) isotherm loops of PEVA(9.9mol% and 17.8mol% VA)-DME system are obtained. The cloud-point curves for PEVA(9.9mol% and 17.8 mol% VA) copolymers andthe ethylene, propane, propylene, n-butane, 1-butene, and CDFM all show negative slopes of phase behavior and are located at pressures below 1,800 bar. For PEVA copolymer-DME system(9.9mol% VA), cloud-point curves show positive slopes that decrease in pressures with decrease in temperature in the temperature range of $80^{\circ}C$ to $160^{\circ}C$.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.107-107
• /
• 2017

3D bioprinting is a technology to produce complex tissue constructs through printing living cells with hydrogel in a layer-by-layer process. To produce more stable 3D cell-laden structures, various materials have been developed such as alginate, fibrin and gelatin. However, most of these hydrogels are chemically bound using crosslinkers which can cause some problems in cytotoxicity and cell viability. On the other hand, thermosensitive hydrogels are physically cross-linked by non-covalent interaction without crosslinker, facilitating stable cytotoxicity and cell viability. The examples of currently reported thermosensitive hydrogels are poly(ethylene glycol)/poly(propylene glycol)/poly(ethylene glycol) (PEG-PPG-PEG) and poly(ethylene glycol)/poly(lactic acid-co-glycolic acid) (PEG/PLGA). Chitosan, which have been widely used in tissue engineering due to its biocompatibility and osteoconductivity, can be used as thermosensitive hydrogels. However, despite the many advantages, chitosan hydrogel has not yet been used as a bioink. The purpose of this study was to develop a bioink by chitosan hydrogel for 3D bioprinting and to evaluate the suitability and potential ability of the developed chitosan hydrogel as a bioink. To prepare the chitosan hydrogel solution, ${\beta}-glycerolphosphate$ solution was added to the chitosan solution at the final pH ranged from 6.9 to 7.1. Gelation time decreased exponentially with increasing temperature. Scanning electron microscopy (SEM) image showed that chitosan hydrogel had irregular porous structure. From the water soluble tetrazolium salt (WST) and live and dead assay data, it was proven that there was no significant cytotoxicity and that cells were well dispersed. The chitosan hydrogel was well printed under temperature-controlled condition, and cells were well laden inside gel. The cytotoxicity of laden cells was evaluated by live and dead assay. In conclusion, chitosan bioink can be a candidate for 3D bioprinting.

• Journal of the Korean Electrochemical Society
• /
• v.4 no.1
• /
• pp.6-9
• /
• 2001

[ $SiO_2$ ] effect on the electrochemical properties of polymeric gel electrolytes(PGEs) reinforced with glass fiber cloth(GFC) was investigated . PGEs were composed of polyacrylronitrile(PAN), poly(vinylidenefluoride-co-hexafluoropropylene) (P(VdF-co-HFP)), $LiClO_4$ and three kind of plasticizer(ethylene carbonate, dietyl carbonate, propylene carbonate). $SiO_2$ was added to PGEs in the weight fraction of 10, 20, $30\%$ respectively. PGEs containing $SiO_2$ showed conductivity of over $10^{-3}S/cm\;at\;23^{\circ}C$ and electrochemical stability window to 4.8V. In the impedance spectra of the cells, which were constructed by lithium metals as electrodes, interfacial resistance increased due to growth of passivation layer during storage time and remarkable difference was not observed with content of $SiO_2$. In the impedance spectra of the lithium ion polymer batteries consisted of $LiClO_2$ and mesophase pitch-based carbon fiber(MCF), ohmic cell resistance of $SiO_2-free$ PGE was changed continuously with number of cycle, but those of $SiO_2-dispersed$ PGEs were not. Discharge capacity of the PGE containing $20wt\%\;SiO_2$ showed 132 mAh/g at 0.2C rate and $85\%$ of discharge capacity was retained at 2C rate.

• Membrane Journal
• /
• v.26 no.2
• /
• pp.126-134
• /
• 2016

To produce renewable biomethane from biogas, the properties of physical absorbents such as water, methanol, 1-methyl-2-pyrrolidone (NMP), poly(ethylene glycol) dimethylether (PEGDME), and propylene carbonate (PC) were studied, and PC was applied to membrane contactor systems. Among physical absorbents, PC exhibited a high contact angle of $58.3^{\circ}$ on polypropylene surface, and a PC/water mixture (5 wt%) increased the contact angle to $90^{\circ}$. Furthermore, the PC/water mixture presented higher $CO_2$ absorption capacities (0.148-0.157 mmol/g) than that of water (0.121 mmol/g), demonstrating a good property as an absorbent for membrane contactors. Actual operations in membrane contactors using the PC/water mixture resulted in $CO_2$ removal of 98.0-97.8% with biomethane purities of 98.5-98.3%, presenting a strong potential for biogas treatment. However, the PC/water mixture yielded moderate improved in $CO_2$ removal and methane recovery, as compared with water in the membrane contactor operation. This is originated from insufficient desorption processes to reuse absorbent and low $CO_2$ flux of the PC/water absorbent. Thus, it is requiring optimizations of membrane contactor technology including development of absorbent and improvement of operation process.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.8
• /
• pp.2342-2348
• /
• 2014

Poly(lactic-co-glycolic acid) (PLGA) were grafted to both ends of Pluronic$^{(R)}$ F68 ($(EO)_{75}(PO)_{30}(EO)_{75}$) triblock copolymer to produce poly{(lactic acid)$_m$-co-(glycolic acid)$_n$}-b-poly(ethylene oxide)$_{75}$-b-poly(propylene oxide)$_{30}$-b-poly(ethylene oxide)$_{75}$-b-poly{(lactic acid)$_m$-co-(glycolic acid)$_n$} (PLGA-F68-PLGA) pentablock copolymers. Molecular weights of PLGA blocks were controlled and five kinds of pentablock copolymers with different PLGA block lengths were synthesized using in-situ ring-opening polymerization of D,L-lactide and glycolide with tin(II) 2-ethylhexanoate ($Sn(Oct)_2$) catalyst. PLGA-F68-PLGA pentablock copolymers were characterized by $^1H$- and $^{13}C$-NMR, GPC, and TGA. The numbers (2m, 2n) of repeating units for lactic acid and glycolic acid inside PLGA segments were obtained as (48, 17), (90, 23), (125, 40), (180, 59), and (246, 64), with $^1H$-NMR measurement. From NMR data, the resultant molecular weights were determined in the range of 12,700-29,700, which were similar to those obtained from GPC. Polydispersity index was increased in the range of 1.32-1.91 as the content of PLGA blocks increased. TG and DTG thermograms showed discrete degradation traces for PLGA and F68 blocks, which indicate the weight fractions of PLGA blocks in pentablock copolymers can be calculated by TG profile and it is possible to remove PLGA block selectively. Hydrodynamic radius and radius of gyration of pentablock copolymer micelle were obtained in the range of 46-68 nm and 31-49 nm, respectively, in very dilute (i.e. 0.005 wt %) aqueous solution of THF:$H_2O$ = 10:90 by volume at $25^{\circ}C$.