• 한국자동차공학회논문집
• /
• 제12권5호
• /
• pp.1-11
• /
• 2004

In order to recognize thermal efficiency and power improvement in case that diesel cycle is turned into diesel-atkinson cycle, the fuel-air diesel-atkinson cycle considered gas exchange process is analyzed non-dimensionally and thermodynamically. As a result, in case of diesel-atkinson cycle, as expansion ratio is increased, thermal efficiency and mean effective pressure is increased and it has maximum value at Rec=1. When diesel cycle is turned into diesel-atkinson cycle by late intake valve closing timing, thermal efficiency and power is decreased because of the decline of effective compression ratio and intake airflow, but it could be compensated by increase of compression ratio or super-charged. In case compression ratio is compensated, Rec appears 1 around 100$^{\circ}$ ABDC, and it is expected that thermal efficiency is enhanced by 14.3% compared with conventional diesel cycle. In case compression ratio and intake airflow are compensated simultaneously, super-charged pressure is demanded 2.06bar at Rec=1 and it is more efficient when only compression ratio is compensated in the view point of thermal efficiency.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2006년도 춘계학술논문 발표대회 제6권1호
• /
• pp.5-8
• /
• 2006

High strength concrete has been increasingly used in high rue building and it is very obvious re consider fire resistance performance of that. Unlike the normal strength concrete, high strength concrete in sudden elevating temperature at fire is susceptible to spalling with severe explosion and surface split, due to high density of concrete. In order to endure the spalling, inner space temperature of concrete should be control less than certain point. Therefore this study investigated the influence of covering materials on high strength concrete finishing spray-on materials of fiber composite spray mortar(FCSM). Both polypropylene(PP) and polyvinyl alcohol(PVA) fiber were used in this test. Test showed that concrete, covering 18mm mortar containing PVA fiber and confining metal lath 2.3mm thickness, decreased 50% of main bar ambient temperature. compared with control concrete. In addition, concrete covering 18mm mortar without fiber caused falling of covering materials and then it was exposed in elevating temperature. As a result, spatting of the concrete occurred same as control concrete. However, concrete covering spray-on mortar containing PVA or PP fiber resisted spatting occurrence.

• 대한기계학회논문집
• /
• 제12권1호
• /
• pp.137-151
• /
• 1988

본 논문에서는 아래 평판은 높은 온도 $T_{h}$로 유지되고, 위의 평판은 낮은 온도 $T_{i}$로 유지되어 있을 때 온도차에 의하여 발생하는 난류 열대류 문제를 난류모델 방정식을 사용하여 수치적으로 해석하고자 한다.다.다.

• 한국운동역학회지
• /
• 제16권2호
• /
• pp.109-120
• /
• 2006

The purpose of this study was to examine the kinematical characteristics of gymnasts who can perform the KOVACS skill, and to grope for the better KOVACS Piked motion. The subjects were 3 male national gymnasts and were filmed with video cameras. And kinematic data were collected from the event of maximum knee flexion to the re-grasp the bar after airborne motion during KOVACS Piked motion. And the following conclusion were drawn; S1 took the enough time and inadequate height for performing KOVACS Piked motion. S2 showed the inadequate time and height during airborne motion with the large forward-backward and left-right movement. S3 showed the better KOVACS Piked movement among gymnasts, but the weak point of S3 was the large left-right shift. Based on the above conclusions, the gymnasts should be trained the enough time and height for the effective airborne movement and to reduce the left-right movement.

• 한국기계가공학회지
• /
• 제12권2호
• /
• pp.81-90
• /
• 2013

A study on the flow-structure characteristics of marine 3/2WAY pneumatic valve is essential for optimizing the performance of ship engines. It is important that the valve has desirable safety factor and reduced weight from safety and economic point of view. In this paper, flow-structure characteristics of pneumatic valve is obtained by being optimized based on the proper design criteria. The air with the pressure of 30 bar is the working fluid which is made to fill in the tack in short time. This time is defined as the filling time. On optimum design by considering the flow-structure characteristics, the approach is based on (1) the mathematical formulation of design decisions using the compromise decision-making method, and (2) the approximation technique of response surfaces. The methodology is demonstrated as the multi-objective optimization tool to improve the performance of marine 3/2WAY pneumatic valve.

• 대한화학회지
• /
• 제37권3호
• /
• pp.279-286
• /
• 1993

물-메탄올 혼합용매에서 KCl의 용매화에 미치는 압력의 효과를 알기 위하여 여러 가지 압력하에서 물-메탄올 혼합 용매의 밀도와 점성도 및 이 혼합용매하에서 KCl의 무한희석시 당량 전도도를 측정하여 r-함수를 구하였다. 25$^{\circ}C$, 1기압에서 KCl의 r-함수는 물에서는 0.613이나 메탄올의 양이 증가함에 따라 감소하다가 다시 증가하였으며 고압하에서도 대기압에서와 비슷한 변화의 경향을 보였다. 일정 압력하에서는 메탄올의 양이 증가함에 따라 r-함수가 감소하다가 다시 증가하였으나, 일정 용매조성에서 압력이 증가하면 r-함수는 감소하였다.

• International Journal of Railway
• /
• 제1권2호
• /
• pp.31-36
• /
• 2008

$DF_{21}$ diesel locomotive was designed to satisfy the requirement of Kunming Meter track and the 2Co self-guided radial bogie was used to suit the complex curve track. There are totally 12 locomotives was served on the track. The first two locomotives were devotion running on the track since April 2003, the wheel tread splling was occurred on the middle wheel set of the two locomotives after running nearly 150 thousands km on the track of the two locomotives at August 2004. The dynamic analysis was carried out to find the reason. The wheel set longitudinal vibration resonance phenomenon was existed on the locomotive dynamic performance, and this was caused by the too big longitudinal stiffness of the journal box bar on the middle wheel set. Wheel set longitudinal vibration resonance maybe an important reason of lead to wheel tread spalling. The corresponding mend methods were put forward from the point of view of wheel set longitudinal vibration resonance. All the wheel tread of the 12 locomotives on the middle wheel set were in good condition and not occurred the wheel tread spalling after the mend till December 2007 after 350 thousands km were finished. The mechanism of the wheel tread splling and corresponding mend method was discussed in detail in this paper.

• 콘크리트학회논문집
• /
• 제11권3호
• /
• pp.141-152
• /
• 1999

Precast prestressed double-tee slab may be designed by the PCI Design Handbook. It is based on the bridge construction and is required for reorganization for the use of buildings in the domestic construction environments. Much enhanced sections are developed from the reforming process on the determined design factors in the previous experimental works on double tees. Pre-determined shape, reinforcement detail, and 5000 psi concrete strength can not be expected as the best solution for the domestic construction requirements because large amount of use on that systems are anticipated. Flexural tests are performed on four full-scale 12.5m proto-type models, "least depth double tee", which are resulted from the optimization process. Domestic superimposed live load regulation, domestic material properties which is available to product, building design requirements and economy in construction are considered as the main factors to establish. the first two sections are double tee section for 1.2 ton/$\m^2$ market live load with straight and one-point depressed strands and the second two are for 0.6 ton/$\m^2$ parking live load with those strand types. All of the specimens tested fully comply with the flexural strength requirements as specified by ACI 318-95. However, the research has shown that following improved considerations are needed for better result in practice. The locations and method of connection for the lowest bottom mild bar, connection method between precast and cast-in-place concrete, and dap-end reinforcement are need to be improved.

• 동력기계공학회지
• /
• 제6권1호
• /
• pp.55-60
• /
• 2002

There has been no report on the life prediction for gas turbine materials at high temperatures based on the creep properties and their relationship with the AE(acoustic emission) properties as a means of real-time non-destructive testing. One of the important issues is thus to develop a reliable method of evaluating creep properties by the AE technique. In this paper, the real-time evaluation of high temperature creep time and AE cumulative counts for nickel-based superalloy Udimet 720 was performed on round-bar type specimens under pure load at the temperatures of 811, 922 and 977K. The total AE cumulative counts until the starting point of secondary creep($N_1$) and that of tertiary creep($N_2$) have quantitative relationship with the tertiary creep time and the rupture time. It is thus possible to construct the life prediction system based on creep and the prevention system of tertiary creep by using AE technique.

• Smart Structures and Systems
• /
• 제31권5호
• /
• pp.517-529
• /
• 2023

Using a device composed of two lateral pressure plates (LPPs) and a steel reinforcement bar to apply horizontal pressure on slope surfaces, a newly developed prestress-reinforced embankment (PRE) is proposed, to which can be adopted in strengthening railway subgrades. In this study, an analytical model, which is available of calculating additional confining stress (σ_H) at any point in a PRE, was established based on the theory of elasticity. In addition, to verify the proposed analytical model, three dimensional (3D) finite element analyses were conducted and the feasibility in application was also identified and discussed. In order to study the performance of the PRE, the propagation of σ_H in a PRE was analyzed and discussed based on the analytical model. For the aim of convenience in application, calculation charts were developed in terms of three dimensionless parameters, and they can be used to accurately and efficiently predict the σ_H in a PRE regardless of the embankment slope ratio and LPP side length ratio. Finally, the potential applications of the proposed analytical model were discussed.