• Journal of Korean Society of Forest Science
• /
• v.48 no.1
• /
• pp.40-50
• /
• 1980

This research was carried out to examine the substitutional feasibility of low-priced materials produced in waste of forest instead of wheat flour which is extended for plywood adhesives. Wheat, pine bark, wood flour and pine foliage of coniferous trees or poplar foliage of hardwood species were selected and pulverized into 60-100 mesh minute powder after they were dried at $100-105^{\circ}C$ during 24 hours in the drying oven. The prepared particles as above were added to urea formaldehyde resin, urea-melamine copolymer resin and water soluble phenol formaldehyde resin in the ratio of 10, 20, 30 and 50%. After plywoods were processed by the above extending ratios, shear strength of extended plywoods were analyzed and discussed. The results obtained at this study were summarised as follows; 1. In the case of urea formaldehyde resin, both dry and wet shear strength of plywoods extended by wheat flour were shown the highest value. 2. Dry shear strength of urea-melamine copolymer resin was better than that of urea formaldehyde resin on the whole, while plywoods extended by wheat flour were shown excellent results. 3. Among 10% and 20% extensions of urea-melamine copolymer resin, the best results were shown by poplar leaves powder, wheat powder and wood flour. They had no significant difference statistically. 4. In the case of water soluble phenol formaldehyde resin, although dry shear strength of pine leaves powder was higher than that of wheat flour in the ratio of 10%, there was no significant difference between them in the ratio of 10 and 20%. 5. Among 20, 30 and 50% extensions of water soluble phenol formaldehyde resin, wet shear strength of wood flour and bark powder was higher than that of wheat flour. Wet shear strength of wood flour in the ratio of 10% was shown the same tendency as above.

• Journal of the Korean Wood Science and Technology
• /
• v.9 no.3
• /
• pp.16-23
• /
• 1981

This study has been carried out to make a comparative study for the adhesive control methods specifically developed for application to formaldehyde. The method for formaldehyde determination used in this report is the improved chromo tropic acid determination. The results are summarized as follows: 1. The soaking treatment in aqueous solution of urea wok the most scavenging effect on the formaldehyde release from a plywood sample glued with a urea formaldehyde adhesive, and other removal treatment such as resorcinol, albumine-, and hardener-treatment gave significant reduction too. 2. In glue shear strength of dry test, 2% of resorcinol treatment and soaking treatment showed the highest strength and all the other treatment met the standard, but in hot water soaking test, 2% of resorcinol treatment gave the best results, on the other hand, adding the hardener showed the lowest strength and failed in meeting the standard. 3. Air dried moisture content of all treated plywood met the standard which calls for 13% or bellow. 4. In this comparative study, we can make a strong combination each other or go into the details of one treatment for the best result through the more study.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.5
• /
• pp.65-71
• /
• 2003

In this paper, bending capacities of glulams with different configurations of cross-section were evaluated. These configurations included horizontal(BH), vertical(BVN), vertical with vertical plywood (BVV) and vertical combination of lamination with horizontal plywood(BVH). Full-scale bending tests were performed to investigate the effect of different section configurations on bending strength(MOR) and stiffness(MOE) of glulam. Compared with type BH, MOR of glulam with type BVN configuration was improved about 23%, which was considered to be caused by defect dispersion effect, while MOE of glulams with these two types of configurations were similar. Because MOE of plywood is generally smaller than that of solid wood laminar, MOE of type BVH glulam decreased about 15%, but in the case of type BVV glulam, MOR was improved without any reduction of MOE. The reason of this result could be undersood in the view of shear-reinforcement effect, which was verified from analysis of fracture mode. From the results of this study, it was concluded that bending capacity of glulam could be improved by proper section design, such as laminar arrangement and shear reinforcement.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.118-131
• /
• 1982

1. In order to investigate the effect of variation of assembly time on glue bond strength, and to determine the optimum range of assembly time with given glue, this experiment was made at the suggestion of the Wood Technology Laboratory, School of Forestry, Yale University. 2. For this investigation, three-ply-plywoods with 1/22 inch, birch veneer, phenolic resin, and soybean glue were made at the following variation of assembly time, that is, 1, 5, 10, 25, 35, 50, and 70 minutes, under both open and closed assembly manners, and the shear strength test at dry and wet were adoptted. 3. The shear strength and wood failure of each plywood panel constructed at the given assembly time have been illustrated in Tables 1, 2, 3 and 4. It has shown that there is a remarkable tendency, for increasing assembly time to give lower shear strength and wood failure throughout almost all cases. The effective range of assembly time of tested glues in this investigation for both open and closed assembly are summarized in the Table 7. Thus, allowable assembly time for Phenolic resin may be up to 10 minutes under open assembly and up to 50 minutes under closed assembly. For soybean glue, the permissible assembly time may be up to 5 minutes under open assembly and up to 15 minutes under closed assembly. The allowable assembly time for open assembly with the same glue is reduced by approximately one third or more than one third as compared with closed assembly time. This might mean that the closed asembly time for these glues is more practical than the open assembly.

• Journal of Korea Foresty Energy
• /
• v.24 no.1
• /
• pp.28-32
• /
• 2005

This study was performed to find a new use of wood tar from the manufacturing process of wood charcoal. Plywoods made of phenol adhesives mixed with wood tar were manufactured, and physical, mechanical properties and formaldehyde emission were investigated. Plywoods made of phenol adhesives mixed with wood tar were almost same as an original phenol adhesive in physical and mechanical properties and tensile-shear adhesive strength of the plywood was higher than the original one in both non-waterproof and waterproof tests. Formaldehyde emission was lower as the amount of wood tar increased in phenol adhesive.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.3
• /
• pp.36-44
• /
• 2007

The purpose of this study was to investigate thermal stability, reactivity, and bonding strength of existing epoxy resin mixed with the epoxidized soybean oil (ESBO) in order to use soybean oil economically. In the dry shear test, the marked strengths showed $30.5kgf/cm^2$ at the ratio of ESBO to epoxy resin 9 : 1 and $6.2kgf/cm^2$ at the ratio 8 : 2. The bonding strengths of the others, except mixing ratios 2 : 8 and 1 : 9, exceeded the requirement of Korean plywood standard of $7.0kgf/cm^2$. In the wet shear test, the result was $5.8kgf/cm^2$ at the ratio 9 : 1. There were no thickness swelling and moisture absorption in the water resistance of the film. The value of activation energy, Tg (${\Delta}E$), by DSC analysis showed between $110^{\circ}C$ and $120^{\circ}C$ through all ratios. Epoxy in the epoxy resin fully reacted with the hardener (TETA), but it is difficult to decide that epoxys in the ESBO were reacted directly with the hardener from FT-IR analysis. As the mixing ratio of ESBO increased, the thermal stabilities dropped from TGA analysis. From the comprehensive view on the results of above experiments, it could be confirmed through experiments that the ESBO in the mixed adhesive of epoxy resin/ESBO played a role as an extending agent level of epoxy adhesive, and we were able to know that in order to utilize ESBO as an adhesive, a study should be performed on the condition of hardening, inducible of the hardening reaction.

• Journal of the Korean Wood Science and Technology
• /
• v.12 no.1
• /
• pp.3-10
• /
• 1984

Taro-UF mixed type resin system was developed for gluing plywoods. The taro adhesive that was activated with sodium hydroxide was mixed with the definite ratios of UF resin adhesive. At the sametime, wheat-UF mixed type resin was also applied with the same method as taro-UF mixed type resin The mixing ratios of taro or wheat adhesive: UF resin were 0:100, 10:90, 20:80, 30:70, 40:60, 50:50, 60:40, 80:20, and 100:0 by weight. In addition, the UF resins extended with wheat powder at the extending ratios of wheat powder UF resin, 10:90, 20:80, 30:70, 40:60, and 50:50 by weight, were also used. The dry and wet shear strengths of the plywoods of 30:70 (taro adhesive : UF resin) mixing ratio were highest. The dry shear strengths of the plywoods manufactured with the UF resin-mixing taro adhesive were higher than those of the plywoods with the UF resin-mixing wheat adhesive at 10:90, 20:80, 30:70, 40:60, 50:50, and 60:40 (taro or wheat adhesive: UF resin) mixing ratios. At all mixing ratios, the wet shear strengths of the plywoods manufactured with the UF resin-mixing taro adhesive were higher than those of the plywoods with the UF resin-mixing wheat adhesive. The dry and wet shear strengths of the plywoods manufactured with the UF resin-mixing wheat adhesive were higher than those of the plywoods with the wheat powder-extending UF resin at the mixmg ratios, 10:90, 20:80, 30:70, and 40:60 (wheat adhesive or wheat powder: UF resin). So, it was found that the plywoods manufactured with the UF resin-mixing taro adhesive and the UF resin mixing wheat adhesive had better shear strength than the plywoods with the wheat powder-extending UF resin. It was because the taro adhesive and wheat adhesive themselves took the bonding properties after being activated with alkali.