• 한국지하수토양환경학회지:지하수토양환경
• /
• 제8권3호
• /
• pp.56-60
• /
• 2003

전기분해에 의한 부상현상을 이용하여 유류로 오염된 토양 세정 후 발생되는 유출수 중 유분 등을 분리하기 위한 적정 운전조건을 찾고자 하였다. 전기분해 반응조(200${\times}$10${\times}$15cm)를 이용하여 혼합계면활성제($POE_5$ : $POE_{14} $, 1:1) 1%용액에 디젤을 1,000 mg/L 농도로 용해시켜 실험하였다. 양극에는 티타늄 코팅전극, 음극으로는 스테인레스 스틸전극을 이용하였다. 반응시간은 62분(반응 :60분, 부상시간 :2분)이었으며 전압은 6V였다. 전해질 첨가에 의한 영향을 알아보기 위하여 실험한 결과, 전해질을 첨가하였을 경우 첨가하지 않았을 때보다 40% 정도의 효율이 증가하였다. 적정 전해질, 주입농도 및 반응시간을 알아보기 위하여 1N NaCl과 NaOH의 농도를 변화시켜 가면서 실험하였다. NaCl의 경우 더 좋은 효율을 나타내었다. 전해질의 농도는 0.2-1.0%의 농도범위에서 NaCl와 NaOH 모두 농도에 따라 순차적으로 효율이 증가하였다. 두 전해질 모두 0.4-1.0% 농도 범위에서 평형에 도달하는 시간은 20분으로 나타났다.

• 한국산업융합학회 논문집
• /
• 제6권1호
• /
• pp.81-86
• /
• 2003

For the simultaneous removal of $SO_2$/NOx from an iron-ore sintering plant, industrial plasma experiments have been conducted with a flue gas flow rate of $5,000Nm^3/hr$. The maximum 40kW power using the magnetic pulse compression (MPC) system generates a peak value of 100-150kV pulse voltage with its risetime of 200nsec and full width at half maximum (FWHM) of 500nsec, and with a frequency <300Hz. The plasma reactor module adopts a wire-plate structure with a gap of 200-400mm ID between plates. Initial concentrations of $SO_2$ and NOx were around 100-150ppm, respectively in the presence of 15% $O_2$ and <10% $H_2O$. Various reaction parameters such as specific energy ($Whr/Nm^3$), $NH_3$ injection with corona discharge, flow rate and injection of hydrocarbons were investigated for $SO_2$/NOx removal characteristics. About 90/65% of $SO_2$/NOx were simultaneously removed with a specific energy of $3.0Whr/Nm^3$ when both $NH_3$ and hydrocarbons were injected. Practical implications that the pilot-scale plasma results provide are further discussed.

• 조명전기설비학회논문지
• /
• 제19권4호
• /
• pp.1-8
• /
• 2005

본 연구에서는 2차원적 유체 모델을 통하여 보다 실질적인 플라즈마를 이해하고자 하였으며, 기하학적인 방전전극 구조를 반영하도록 전극단에서 챔버 외벽의 거리를 변화시키면서 플라즈마의 특성을 정량적으로 비교 분석하고자 하였다. 방전 챔버의 구조로서, 전극의 반경과 방전 챔버의 높이는 일정하게 유지하면서 방전 챔버의 넓이를 변화시킴에 따라 형성되는 플라즈마의 특성을 분석하였다. 그 결과, 전극단과 챔버 외벽의 거리가 짧을수록 그 영역에서 전계가 강하게 형성되어, 외벽을 향하는 각 입자들의 움직임도 매우 활발하다는 것을 알 수 있었다. 또한, 전각단과 외벽과의 거리가 짧을수록 전극 면상에서 형성되는 입자들의 수밀도와 유속의 변화가 일정하게 형성되는 것을 알 수 있었다. 이러한 결과는 웨이퍼의 대구경화에 따른 플라즈마의 균일성을 고려할 경우에 매우 효과적일 것으로 고려되어 진다.

• Journal of Microbiology and Biotechnology
• /
• 제25권9호
• /
• pp.1547-1554
• /
• 2015

The potential of microalgae biofuel has not been realized because of the low productivity and high costs associated with the current cultivation systems. In this study, a new low-cost and transparent attachment material was tested for cultivation of a filamentous algal strain, Stigeoclonium sp., isolated from wastewater. Initially, the different materials tested for Stigeoclonium cultivation in untreated wastewater were nylon mesh, polyethylene mesh, polypropylene bundle (PB), polycarbonate plate, and viscose rayon. Among the materials tested, PB led to a firm attachment, high biomass (53.22 g/m², dry cell weight), and total lipid yield (5.8 g/m²) with no perceivable change in FAME profile. The Stigeoclonium-dominated biofilm consisted of bacteria and extracellular polysaccharide, which helped in biofilm formation and for effective wastewater treatment (viz., removal efficiency of total nitrogen and total phosphorus corresponded to ~38% and ~90%, respectively). PB also demonstrated high yields under multilayered cultivation in a single reactor treating wastewater. Hence, this system has several advantages over traditional suspended and attached systems, with possibility of increasing areal productivity three times using Stigeoclonium sp. Therefore, multilayered attached growth algal cultivation systems seem to be the future cultivation model for large-scale biodiesel production and wastewater treatment.

• 한국수소및신에너지학회논문집
• /
• 제18권4호
• /
• pp.452-457
• /
• 2007

Titanium foil and mesh(anodized tubular $TiO_2$ electrode, ATTE) were anodized in a bath at $5^{\circ}C$ with 20V external bias applied, then annealed at different temperatures($450^{\circ}C{\sim}850^{\circ}C$) to obtain tubular $TiO_2$ on the Ti substrate. The prepared sample was used to investigate rate of hydrogen production as well as Cr(VI) reduction. The ATTEs annealed at relatively lower temperatures showed higher activity than those at relatively higher temperatures. In particular, the Cr(VI) reduction was pH-dependent. To improve photocatalytic Cr(VI) reduction with the ATTEs, two configurations, fixing foil type and rotating mesh type, were also compared. As a result, the rotating mesh type was much more effective for Cr(VI) reaction than the former due to the more efficient use of the light. In the rotating type reactor, as the rotating speed increased, the rate of the Cr(VI) reduction was getting faster.

• Journal of Mechanical Science and Technology
• /
• 제15권3호
• /
• pp.291-299
• /
• 2001

Recently, severe wear on the shutdown rod cladding of Ulchin Nuclear Power Plant #1, #2 were observed by the Eddy Current Test(E.C.T.). In particular, the wear at the sixth card location was up to 75%. The test results indicated that the Flow Induced Vibration(F.I.V.) might be the cause of the fretting wear resulting from the contact between Rod Cluster Control Assemblies(RCCAs) and their spacing cards(guide plates) arranged in the guide tube. From reviewing RCCAs fretting wear repots and analyzing the general characteristics of F.I.V. mechanism in the reactor, geometric layout and flow conditions around the control rod, it is concluded that the turbulence excitation is the most probable vibration mechanism of RCCA. To identify the governing mechanism of RCCA vibration, an experiment was performed for a representative rod position in which the most serious fretting wear experienced among the six rod positions. The experimental rig was designed and set up to satisfy the governing nondimensional numbers which are Reynolds number and mass damping parameter. The vibration amplitude measurement by the non-contact laser displacement sensor showed good agreements in the frequency and the maximum wearing(vibration) location with Ulchin E.C.T. results and Framatome report, respectively. The sudden increase in the vibration amplitude was sensed around the 6th guide plate with mass flow rate variation. Comparing the similitude rod behaviour with the idealized response of a cylinder in flow induced vibration, it was found that he dominant mechanism of vibration was transferred from turbulence excitation to periodic shedding at the mass flow ate 90ι/min. Also the critical velocity of the vibration in RCCAs was determined and the vibration can be prevented by reducing the bypass flow rate below the critical velocity.

• 한국동물위생학회지
• /
• 제30권2호
• /
• pp.259-267
• /
• 2007

A study on the relation between some husbandry practices and brucellosis in goats in Bangladesh was conducted at selected areas of Mymensingh and Dhaka district, Bangladesh, from March 2005 to May 2006. Sera from 300 goats were tested by Rose bengal test (RBT), plate agglutination test (PAT), tube agglutination test (TAT) and mercaptoethanol test (MET). Out of the 300 goats, 1.670% (n=5) were positive to RBT and PAT respectively, and 2.0% (n=6) were positive to TAT and 2.33% (n=7) were positive to MET. The prevalence of brucellosis was bigger in goats reared collectively (n=2, 4%) than reared individually (n=5, 2%), and bigger in goats housed with concrete floor (n=2, 4%) than that of bare floor (n=5, 2%). The rate of brucellosis was higher in goats keep separately (n=6, 2.61%) than that of kept with other animals (n=1, 1.43%) especially with cattle. Out of 290 goats from free grazing, 7 were positive but no positive reactor(n=10) was found in non grazing goats. In conclusion, however, seroprevalence of brucellosis had no statistically significant association with rearing type, housing type and grazing or not.

• 한국해양바이오학회지
• /
• 제1권4호
• /
• pp.292-297
• /
• 2006

오염된 양식 해수의 수질정화능력이 뛰어난 광합성세균의 고순도 대량배양을 위한 실험을 실험실 단위 및 파이롯트 단위에서 수행했다. Gas pack 반응기, flask 반응기 및 N-source로서 질소 가스를 사용한 실험 결과, 광합성세균은 현미경상 약 90%이상의 순도를 나타내었고, CFU 측정 결과에서도 붉은색을 띄는 광합성세균 colony만을 관찰 할 수 있었다. 배지의 교차에 의한 배양실험에서 기초배지를 이용한 배양이 광합성세균의 성장에 가장 효과적임을 알 수 있었다. 이러한 배양조건하에서의 5L bioreactor 배양에서 비증식속도가 $0.18h^{-1}$로 나타났고, 실험실 단위의 결과를 이용한 pilot 단위에서의 배양결과, 실험실 단위의 비증식속도와 동일한 값을 얻을 수 있었다.

• 한국세라믹학회지
• /
• 제44권7호
• /
• pp.368-374
• /
• 2007

CVD-SiC coating has been introduced as a protective layer in TRISO nuclear fuel particle of high temperature gas cooled reactor (HTGR) due to its excellent mechanical stability at high temperature. In order to prevent the failure of the TRISO particles, it is important to evaluate the fracture strength of the SiC coating layer. It is needed to develop a new simple characterization technique to evaluate the mechanical properties of the coating layer as a pre-irradiation step. In present work, direct strength measurement method with the specimen of hem i-spherical shell configuration was suggested. The indentation experiment on a hemisphere shell with a plate indenter was conducted. The fracture strength of the coating layer is related with the critical load for radial cracking of the shell. The finite element analysis was used to drive the semi-empirical equation for the strength measurement. The SiC hemispherical shells were successfully recovered from the section-grinding of TRISO coated particle and successive heat treatment in air. The strength of CVD-SiC coating layer was evaluated from the experimentally measured critical load during the indentation on SiC hemisphere shell. Weibull diagram of fracture strength was also constructed. This study suggested a new strength equation and experimental method to measure the fracture strength of CVD-SiC coating of TRISO coated fuel particles.

• 비파괴검사학회지
• /
• 제24권4호
• /
• pp.307-314
• /
• 2004

배관의 축방향 균열 검사를 위하여 원주 방향으로 진행하는 유도초음파 모드를 적용하였다. 배관의 곡률을 변수로 원주 유도초음파의 분산선도를 계산하였으며 이를 배관 검사에 적용하기 위하여 중수로 피더관의 곡관부 축방향 균열을 탐지에 적용하였다. 상대적으로 낮은 주파수에서는 Lamb 파 특성을 따르나 주파수가 증가함에 따라 평판의 경우, 즉 곡률이 무한대인 경우 첫 번째 $A_0$ 모드와 두 번째 $S_0$ 모드가 합쳐져서 Rayleigh 모드 형태로 변화한다. 한편 곡률을 가진 배관의 경우는 주파수가 증가하더라도 첫 번째 모드와 두 번째 모드가 합쳐지지 않았다. 이러한 해석을 기초로 하여 배관의 일종인 중수로 피더관 곡관부 축방향 결함을 탐지하기 위하여 사각 탐촉자를 사용하여 Rocking 원주 유도초음파 기법을 적용하였다. 원주 방향으로 유도파를 진행시키면서 인공 결함으로부터의 수집된 신호를 분석하여 진동 모드를 확인하였으며 두께 대비 10% 깊이의 notch도 검출할 수 있음을 확인할 수 있었다.