• Journal of the Korean Society of Hazard Mitigation
• /
• v.5 no.4 s.19
• /
• pp.37-47
• /
• 2005

The purpose of this study is to estimate the bearing capacity and settlement characteristics of the weathered granite masses, and on the process to achieve the purpose, in the first place, the weathered degree according to the absorption index was examined and reviewed, then plate bearings test in in-situ depth were tested, and finally the result was compared and examined with the result of the existing, estimate method and pressuremeter test. In order to achieve the purpose of this study, a typical area distributed with weathered granite masses, gyeonggi area, was chosen as a sample site for testing, and in the result, it appeared and found out that the more the weathered degree increases when the plate bearing test are tested, the more the bearing capacity decreases a numerical indexes and the more greatly the width of the decrease of bearing capacity increases around the boundary of specific, weathered degrees. Also, In the result from estimating the bearing capacity of weathered granite masses by the existing, suggested formula, it appeared that there is a tendency that the more the weathered degree increases, the more similar the bearing capacity becomes with the result of plate bearing tests.

• International Journal of Highway Engineering
• /
• v.6 no.2 s.20
• /
• pp.25-36
• /
• 2004

The pressuremeter test can be used as an effective tool for evaluating stiffness of lower pavement layers including subgrade and subbase. At present, the most practical and applicable methods for evaluation of the stiffness of the subgrade and subbase are PBT and CBR in Korea. However, these methods have inherent drawbacks and large variabilities of test results themselves. In this study, an evaluation method and a test procedure that can be used for decision of pavement stiffness using pressuremeter were developed. The obtained results representing stiffness of the subgrade and subbase can replace PBT's soil reaction value k and CBR in design methods. It is found that the developed procedure based on the pressuremeter can provide an effective correaltion between the PBT's soil reaction value k and PMT's reloading modulus ($E_R$).

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.539-545
• /
• 2010

The field plate test has a good potential for determining since it measures both plate pressure and settlement. The deformation modulus of rock mass is differently measured for status of structures. The values of deformation modulus are obtained from laboratory test (uniaxial and triaxial test) and field test (pressuremeter test). Plate load test should be conducted by different loading plate sizes for geological structure of rock mass and scale of structures. In this paper, large plate load tests were performed to predict of structure's behavior and evaluate the ultimate bearing capacity of the foundation on soft rock. Simultaneously, deformation modulus of rock mass was estimated by back analysis of stresses measured in field test under rock mass. Finally, we verified the validation of deformation modulus of rock mass through result of large plate load test and numerical simulation.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.10
• /
• pp.61-74
• /
• 2022

Considering that the number of cases in which a structure foundation is located on weathered rock has been increasing recently, for adequate design bearing capacity of a foundation on weathered rock, allowable bearing capacities of such foundations in geotechnical investigation reports were studied. With reference to the study results, the allowable bearing capacity of a foundation on weathered rock was approximately 400-700 kN/m², with a large variation, and was considered a conservative value. Because the allowable bearing capacity of the foundation ground is an important index in determining the foundation type in the early design stage, it can have a significant influence on the construction cost and period according to the initial decision. Thus, in this study, six large-scale plate-bearing tests were conducted on weathered rock, and the bearing capacity and settlement characteristics were analyzed. According to the test results, the bearing capacities from the six tests exceeded 1,500 kN/m², and it shows that the results are similar with the one of bearing capacity formula by Pressuremeter tests when compared with the various bearing capacity formula. In addition, the elastic modulus determined by the inverse calculation of the load-settlement behavior from the large-scale plate-bearing tests was appropriate for applying the elastic modulus of the Pressuremeter tests. With consideration of the large-scale plate-bearing tests in this study and other results of plate-bearing tests on weathered rock in Korea, the allowable bearing capacity of weathered rock is evaluated to be over 1,000 kN/m². However, because the settlement of the foundation increases as the foundation size increases, the allowable bearing capacity should be restrained by the allowable settlement criteria of an upper structure. Therefore, in this study, the anticipated foundation settlements along the foundation size and the thickness of weathered rocks have been evaluated by numerical analysis, and the foundation size and ground conditions, with an allowable bearing capacity of over 1,000 kN/m², have been proposed as a table. These findings are considered useful in determining the foundation type in the early foundation design.