• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.359-364
• /
• 2004

In this study, experiments were tried on the mixed-mode I+II single overloading model which changes the loading mode of overload and fatigue load. Aspects of deformation field in front of the crack which is formed by mixed-mode I+II single overloading were experimentally studied. Then the shape and size of mixed-mode plastic zone were approximately calculated. The propagation behavior of fatigue crack was examined under the test conditions combined by changing the loading mode. The behavior of fatigue cracks were greatly affected by shapes of plastic deformation field and applying mode of fatigue load. Accuracy of prediction and evaluation for fatigue life may be improved by considering all aspects of deformation and behavior of fatigue cracks.

• 대한기계학회논문집A
• /
• 제25권8호
• /
• pp.1277-1286
• /
• 2001

Aluminum 5052/Aramid Fiber Reinforced Plastic(Al5052/AFRP) laminates are applied to the fuselage-wing intersection. The Al5052/AFRP laminates suffer from the cyclic bending moment of variable amplitude during the service. Therefore, the influence of cyclic bending moment on the delamination and the fatigue crack propagation behavior in Al5052/AFRP laminate was investigated in this study. Al5052/AFRP laminate composite consists of three thin sheets of Al5052 and two layers of unidirectional aramid fibers. The cyclic bending moment fatigue tests were performed with five different levels of bending moment. The shape and size of the delamination zone formed along the fatigue crack between Al5052 sheet and aramid fiber-adhesive layer were measured by an ultrasonic C-scan. The relationships between da/dN and ΔK, between the cyclic bending moment and the delamination zone size, and between the fiber bridging mechanism and the delamination zone were studied. Fiber failures were not observed in the delamination zone in this study. It represents that the fiber bridging modification factor should turn out to increase and that the fatigue crack growth rate should decrease. The shape of delamination zone turns out to be semi-elliptic with the contour decreased non-linearly toward the crack tip.

• 콘크리트학회지
• /
• 제7권4호
• /
• pp.169-179
• /
• 1995

본 논문은 고강도 콘크리트($f'_c=700kg/cm^2$)를 사용한 보_기둥 접합부의 소성힌지 확산을 위하여 중간철근을 수직으로 앵커한 수직앵커형 중간철근으로 보 단부를 보강함으로써 보_기둥 접합부에 발생하는 소성힌지를 보 내측으로 1.0d 만큼 확산시키고자 하는 것이다. 실험의 주 변수로는 중간철근의 유물 및 앵커여부로 설정하여 중간철근의 보강형태에 따른 부재의 역학적 거동을 규명하도록 하였다. 실험결과로부터 보 단부의 1.0d부분을 수직앵커형 중간철근으로 보강하면 소성힌지를 1.0d 부분으로 확산할 수 있었으며, 에너지 분산능력도 ACI318-89에 따라 설계한 관례적인 실험체에 비하여 약 1.6배정도 향상되었다.

• 대한두개안면성형외과학회지
• /
• 제19권3호
• /
• pp.200-204
• /
• 2018

Fibrous dysplasia (FD) is a rare, benign bone disease with abnormal bone maturation and fibroblastic proliferation. Optimal treatment of zone 1 craniofacial FD is radical resection and reconstruction. To achieve of structural, aesthetic, and functional goals, we use three-dimensionally designed calvarial bone graft for reconstruction of zygomatic defect after radical resection of FD. The authors used a rapid-prototyping model for simulation surgery for radical resection and immediate reconstruction. Donor site was selected from parietal bone reflect shape, contour, and size of defect. Then radical resection of lesion and immediate reconstruction was performed as planned. Outcomes were assessed using clinical photographs and computed tomography scans. Successful reconstruction after radical resection was achieved by three-dimensional calvarial bone graft without complications. After a 12-month follow-up, sufficient bone thickness and symmetric soft tissue contour was well-maintained. By considering three-dimensional configuration of zygomaticomaxillary complex, the authors achieved satisfactory structural, aesthetic and functional outcomes without complications.

• Steel and Composite Structures
• /
• 제51권1호
• /
• pp.63-72
• /
• 2024

This study delves into the interaction dynamics between lateral notches and inclusions, providing valuable insights for more effective engineering of structural components. By employing the finite element method, the research analyzes how inclusions affect the dimensions and contours of the plastic zone under confined plasticity conditions. Several parameters were investigated, including loading influence, the distance between the inclusion and notch tip, inclusion stiffness, and the distribution of Von Mises stress, as well as normal stresses σxx and σyy, and Comparison between different stresses. Examining stress distributions under varying loading conditions reveals a significant intensification, particularly near the crack tip. Moreover, the presence of an inclusion near the notch base reduces both the size and shape of the plastic zone. The distribution of the stresses for different loads knows an increase in intensity, especially near the crack head, which is the most requested by the tensile forces on its upper part, which can cause either the crack's initiation or opening, inducing significant stresses.

• 비파괴검사학회지
• /
• 제13권3호
• /
• pp.7-13
• /
• 1993

AISI 4130 금속재를 사용한 균열 컴팩터 인장시편의 파괴거동이 음향방출(AE) 및 초음파 C-scan을 이용하여 조사되었다. 모든 시편들을 특정 수준의 하중까지 증가시키면서, 크랙 개구변위 (COD)와 더불어 여러가지의 음향방출 인자들을 얻었다. 크랙 선단의 크랙 개구변위와 손상(소성)역을 계산하기 위하여 탄소성 유한요소 해석이 수행되었다. 펄스-반사, 침수형으로한 초음파 C-scan은 손상역 크기와 상사시키기 위하여 행해졌다. 유한요소 해석 결과와 측정된 크랙개구변위는 만족할 정도로 일치하였다. 음향방출 결과에서, 시험시편들은 연성거동을 나타내었다. 총 사상수대 크랙 개구변위의 기울기는 크랙 개시점을 결정하는 데에 유용하였다. 예비 시험적인 C-scan 화상은 손상역의 초음파 진폭변화를 보여주었고, 손상역의 형상 및 크기가 유한요소 결과와 정성적으로 부합되었다. 손상역 크기에 관한 추가적인 연구가 요약되었다.

• 한국방재학회 논문집
• /
• 제7권1호통권24호
• /
• pp.11-20
• /
• 2007

본 연구에서는 H형 기둥-보 접합부에서 스캘럽 주변의 파단을 피하기 위해 스캘럽을 생략하고 보와 기둥의 쉬어탭을 볼트로 체결한 후 보 플랜지의 양면에 커버 플레이트와 리브로 보강하는 방법을 제안하였다. 스캘럽을 생략함으로써 스캘럽에서의 응력집중의 빈도를 줄이고 용접부 주위에서의 취성파괴를 방지하여 건축물의 내진성능을 향상시키는데 본 연구의 목적을 둔다. 본 목적을 위해 총 4개의 실험체를 제작하고 반복 가력 실험을 실시하였다. 주요 실험변수는 패널존 강도비이고 실험체의 항복강도, 초기강성, 총소성회전에 대한각 부재의 기여도, 에너지 소산능력으로부터 제작된 실험체들이 특수모멘트골조 내진규정에 만족을 하는지와 실험에 사용된 변수에 대한 여러 영향을 밝히고자 하였다. 그 결과 모든 실험체는 층간변위 4%, 총소성회전 0.03rad.에 충분이 도달하여 1997 AISC의 내진규정에 따라 특수모멘트골조에 만족할 것이라 판단된다.

• Steel and Composite Structures
• /
• 제31권3호
• /
• pp.319-327
• /
• 2019

This paper describes an experimental study of steel beam-column connections with or without expanded beam flanges with different geometries. The objectives of this study are to elucidate the cyclic behavior of these connections, identify the location of the plastic hinge zone, and provide useful test data for future numerical simulations. Five connection specimens are designed and tested under cyclic load. The test setup consists of a beam and a column connected together by a connection with or without expanded beam flanges. A constant axial force is applied to the column and a time varying point load is applied to the free end of the beam, inducing shear and moment in the connection. Because the only effect to be studied in the present work is the expanded beam flange, the sizes of the beam and column as well as the magnitude of the axial force in the column are kept constant. However, the length, width and shape of the expanded beam flanges are varied. The responses of these connections in terms of their hysteretic behavior, failure modes, stiffness degradation and strain variations are experimentally obtained and discussed. The test results show that while the influence of the expanded beam flanges on hysteretic behavior, stiffness degradation and energy dissipation capacity of the connection is relatively minor, the size of the expanded beam flanges does affect the location of the plastic hinge zone and strain variations in these beam-column joints. Furthermore, in terms of ductility, moment and rotational capacities, all five connections behave well. No weld fracture or premature failure occurs before the formation of a plastic hinge in the beam.

• 소성∙가공
• /
• 제6권5호
• /
• pp.446-455
• /
• 1997

A Combined extrusion operation consists of forward and backward extrusion forming and it is possible to make the process be simple by employing it. But the metal flow pattern induced by the operation is hard to analyze accurately because the flows are non-steady, which have at least two directions dependent upon each other. So engineers in the industrial factories had conducted the two extrusion operations separately. A new process was designed by the industrial expert for forming of an alu-minum preform using the combined extrusion operation. In this study, experiments and finite element analysis was carried out to determine the process parameters. Through the preliminary experiment, it was shown that warm forming condition was more desirable than cold or hot ones. And optimal shape of initial billet could be also determined. From the compatibility test, bonde-lube was chosen as the optimal lubricant and 20$0^{\circ}C$ as the material temperature by the inspection of micro-structure. The operation was simulated by the rigid-plastic finite element method to examine the metal flow. Disap-pearing of dead metal zone was observed as the punch fell down and desirable shape was obtained from the one operation. As a result of this study, 7 operations could be reduced and 225% of material saved.

• 소성∙가공
• /
• 제13권6호
• /
• pp.540-545
• /
• 2004

Ever since the ideal forming theory has been developed for process design purposes, application has been limited to sheet forming and, fur bulk forming, to two-dimensional steady flow. Here, application for the non-steady case was performed under the plane-strain condition based on the theory previously developed. In the ideal flow, material elements deform following the minimum plastic work path (or mostly proportional true strain path) so that the ideal plane-stram flow can be effectively described using the two-dimensional orthogonal convective coordinate system. Besides kinematics, fur a prescribed final part shape, schemes to optimize a preform shape out of a class of initial configurations and also to define the evolution of shapes and boundary tractions were developed. Discussions include the two problematic issues on internal tractions and the non-monotonous straining. For demonstration purposes, numerical calculations were made for a bulk part under forging.