• Geomechanics and Engineering
• /
• 제22권4호
• /
• pp.277-290
• /
• 2020

This paper presents an elastic-plastic solution for the circular tunnel of elastic-strain softening behavior considering the pressure-dependent Young's modulus and the nonlinear dilatancy. The proposed solution is verified by the results of the field measuring and numerical simulation from a practical project, and a published closed-form analysis solution. The influence of each factor is discussed in detail, and the ability of Young's modulus and dilatancy characterizing the mechanical response of surrounding rock is investigated. It is found that, in low levels of support pressure, adopting the constant Young's modulus model will seriously misestimate the surrounding rock deformation. Using the constant dilatancy model will underestimate the surrounding rock deformation. When adopting the constant dilatancy model, as the dilation angle increases, the range of the plastic region increases, and the surrounding rock deformation weakens. When adopting the nonlinear dilatancy, the plastic region range and the surrounding rock deformation are the largest. The surrounding rock deformation using pressure-dependent Young's modulus model is between those resulted from two constant Young's modulus models. The constant α of pressuredependent Young's modulus model is the main factor affecting the tunnel displacement. The influence of α using a constant dilatancy model is much more apparent than that using a nonlinear dilatancy model.

• Food Science and Biotechnology
• /
• 제18권4호
• /
• pp.1013-1018
• /
• 2009

Several rheological terms were introduced to estimate the properties of cooked noodles with different starch content using tensile tests. Ring-shaped specimens were prepared by connecting both ends of the noodle strip before cooking. Hencky strain and rate, as well as true stress were applied in constant deformation tests. The elastic region on the curves of strain vs. stress was not clearly identified. Strain hardening in the subsequent plastic region was more prominent in low-starch noodles. Elongational viscosities at lower strain rates were used to differentiate noodles with different starch content, representing the dominant effect of protein content in the range of lower strain rates. In stress relaxation tests, the reciprocal of Peleg's constant $K_1$ (initial decay rate) and $K_2$ (asymptotic level) increased and decreased respectively, with an increase in starch content. This indicated that addition of starch contributed to the noodles becoming viscous liquid rather than elastic solid.

• Journal of Magnetics
• /
• 제16권3호
• /
• pp.294-299
• /
• 2011

Nd-Fe-B high performance magnets were prepared by die-upset forging. The effects of the deformation parameters on magnetic properties and flow stress were studied. Deformation temperatures in the range of $600{\sim}900^{\circ}C$ enable to achieve an effective anisotropy and temperature $800^{\circ}C$ proves to be suitable for deformation of Nd-Fe-B magnets. The amount of c-axis alignment along the press direction seems to depend on the amount of deformation and a saturation behavior is shown at deformation ratio of 75%. Magnetic properties are also related to strain rate, and maximum energy product is attained at an optimum strain rate of ${\varphi}=1{\times}10^{-2}s^{-1}$. By analyzing the relationship of stress and strain at different deformation temperature during die-upset forging process, deformation behavior of Nd-Fe-B magnets was studied and parameters for describing plastic deformation were obtained. Nd-rich boundary liquid phase, which is additionally decreasing the flow stress during deformation, is supposed to play the role of diffusion path and enhance the diffusion rate.

• 전산구조공학
• /
• 제7권3호
• /
• pp.133-141
• /
• 1994

강도활용을 극대화한 볼트의 소성역체결시 볼트의 항복은 볼트에 발생한 인장응력과 너트 나사산과의 접촉면에서 오는 마찰토오크에 의한 전단응력과의 조합에 의한 영향을 받는다. 볼트는 최소단면적인 나사부중 너트와 물리지 않은 여우나사부에서 먼저 항복을 일으킨다. 볼트재료는 대체로 항복과 더불어 소성경화를 보이며 그 정도는 고강도재료에서 인장강도의 10%정도이다. 본 연구에서는 소성역체결시의 거동해석을 변형도증분이론에 의거 해석하였다. 항복은 최소단명이 원통의 표면에서 시작되며 이를 두께가 얇은 원통으로 취급하였다. 항복의 전파는 이들 얇은 원통이 체결이 진행됨에 따라 순차적으로 항복에 이르는 것으로 보고 이 얇은 원통들을 항복시키는데 필요한 축력과 토오크를 합하여 체결종료시의 볼트축력과 (나사면마찰) 토오크로 하였다. M10미터 가는 나사를 계산과 실험에 사용하였다. 축력과 마찰토오크의 마찰계수에 대한 변화관계를 보여주는 그래프와 더불어 실험에서 사용한 볼트의 설계보조 선도를 제시하였다. 이 설계보조용 선도는 실험실에서 얻어진 토오크계수와 마찰계수와의 관계를 그린 것으로 윤활, 포면처리등 현장조건에 따라 달라진 마찰계수를 적절히 취급하는데 효과적으로 활용이 가능하다.

• 소성∙가공
• /
• 제8권3호
• /
• pp.283-283
• /
• 1999

In the present study, the effect of microporosity on the tensile properties of as-cast AZ91D magnesium alloy was investigated through experimental observation and numerical prediction. The test specimens were fabricated by die-casting and gravity-casting. For gravity-casting, the inoculation and use of various metallic moulds were applied to obtain a wide range of microporosity. The deficiency of the interdendritic feeding of the liquid phase acted as d dominant mechanism on the formation of the micropores in the Mg-Al-alloys, rather than the evolution of hydrogen gas. Although tensile strength and elongation has a nonlinear and very intensive dependence upon microporosity, the yield strength appeared to have a linear relationship with microporosity. However, it was possible to quantitatively estimate the linear contribution of microporosity on the individual tensile property far a range of microporosity, which was below about B %. The numerical prediction suggests that the effect of microporosity on fractured strength and elongation decreased as the strain hardening exponent increased. Furthermore. the shape and distribution of micropores may play a more dominant role than local plastic deformation on the tensile behavior of AZ9lD alloy.

• Structural Engineering and Mechanics
• /
• 제9권4호
• /
• pp.375-382
• /
• 2000

Experimental investigation into the cyclic behaviour of sand plast brick masonry was performed on forty two square panels. The panels were subjected to cyclic uniaxial compression for two cases of loading: normal to bed joint and parallel to bed joint. Experimental data were used to plot the unloading-reloading curves for the entire range of the stress-strain curve. Mathematical expressions to predict the reloading and unloading stress-strain curves at various values of residual strain are proposed. A simple parabola and an exponential type formula are found adequate to model the unloading and reloading curves respectively. The models account for the potential effects of residual strain on these curves. Comparison of test results with the proposed mathematical expression shows good correspondence.

• Nuclear Engineering and Technology
• /
• 제53권2호
• /
• pp.647-656
• /
• 2021

Knowing a material's true stress-strain curve is essential for performing a nonlinear finite element analysis to solve an elastoplastic problem. This study presents a simple methodology to determine the true stress-strain curve of type 304 and 316 austenitic stainless steels in the full range of strain from a typical tensile test. Before necking, the true stress and strain values are directly converted from engineering stress and strain data, respectively. After necking, a true stress-strain equation is determined by iteratively conducting finite element analysis using three pieces of information at the necking and the fracture points. The Hockett-Sherby equation is proposed as an optimal stress-strain model in a non-uniform deformation region. The application to the stainless steel under different temperatures and loading conditions verifies that the strain hardening behavior of the material is adequately described by the determined equation, and the estimated engineering stress-strain curves are in good agreement with those of experiments. The presented method is intrinsically simple to use and reduces iterations because it does not require much experimental effort and adopts the approach of determining the stress-strain equation instead of correcting the individual stress at each strain point.

• 한국지반공학회논문집
• /
• 제26권8호
• /
• pp.5-14
• /
• 2010

지반모형실험에서 2차원 평면변형률 상태를 모사하기 위해서는 흙을 담을 수 있는 두꺼운 유리 또는 플라스틱 시트의 토조가 필요하며, 이 때 흙과 접촉되는 토조벽면에서의 마찰저항을 최소화 하여야 한다. 하지만, 실제로 이러한 벽면마찰을 완전히 제거할 수는 없다. 본 연구에서는 벽면 마찰저항을 제거하기 위해 다양한 지름을 갖는 알루미늄 봉 지반모델을 도입하고 실내전단시험에 적용하였다. 또한 근거리 사진계측기법을 전단시험에 적용해 유용성을 검증하였다. 그 결과, 근거리 사진계측으로부터 얻은 평균 팽창각은 전단시험의 전단변형률-체적변형률 곡선으로부터 얻는 팽창각에 근접함을 확인할 수 있었다.

• Geomechanics and Engineering
• /
• 제14권1호
• /
• pp.1-8
• /
• 2018

This paper presents an investigation of the liquefaction characteristics and particle crushing of isotropically consolidated silica sand specimens at a wide range of confining pressures varying from 0.1 MPa to 5 MPa during undrained cyclic shearing. Different failure patterns of silica sand specimens subjected to undrained cyclic loading were seen at low and high pressures. The sudden change points with regard to the increasing double amplitude of axial strain with cycle number were identified, regardless of confining pressure. A higher cyclic stress ratio caused the specimen to liquefy at a relatively smaller cycle number, conversely producing a larger relative breakage $B_r$. The rise in confining pressure also resulted in the increasing relative breakage. At a specific cyclic stress ratio, the relative breakage and plastic work increased with the rise in the cyclic loading. Less particle crushing and plastic work consumption was observed for tests terminated after one cyclic loading. Majority of the particle crushing was produced and majority of the plastic work was consumed after the specimen passed through the phase transformation point and until reaching the failure state. The large amount of particle crushing resulted from the high-level strain induced by particle transformation and rotation.

• 열처리공학회지
• /
• 제31권1호
• /
• pp.18-23
• /
• 2018

In this study, low cyclic fatigue test was carried out at room temperature condition for rolled STS304 steel. The results of this study show that rolled STS304 steel has excellent static tensile strength and fatigue characteristics. The relationship between plastic strain range and fatigue life was examined using the triangular wave in order to predict the low cycle fatigue life of rolled STS304 steel by Coffin-Manson equation. Cyclic behavior of rolled STS304 steel was characterized by cyclic hardening with increasing number of cycle through the Hysteresis loop analysis and cyclic response of maximum stress versus number of cycles. It is found that the plastic deformation energy consumed per cycle is reduced by calculating the area of the hysteresis loop.