• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.3
• /
• pp.361-371
• /
• 2000

RC structure is the composite material system combined concrete and steel showing different plastic behavior. Especially, concrete shows very complex plastic behavior. Therefore, for plastic analysis of RC structures, we have to model carefully each plastic behavior of concrete and steel member. But, because of divergency as well as difficulties and dimensions of modelling, it takes a lot of time and labor or sometimes it is impossible to perform plastic analysis of RC structures. In this study, for simplified plastic analysis of RC structures, we propose material transformation method by homogeneous and isotropic material which have the same plastic property as RC. We generate homogeneous and isotropic material showing the same moment-curvature curves (bi-linear stress-strain relation) as RC members, using bi-linear moment-curvature relation by yielding moment, yielding curvature and ultimate moment, ultimate curvature of RC member. Finally, we prove compatibility in the study by comparing plastic analysis results for various analysis models using transformed material models and RC model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.9
• /
• pp.1914-1922
• /
• 2002

Operating test of power-transmission plastic spur gears were performed inspecting both characteristics of friction-wear and endurance, and suggesting endurance improvement method that either drills internal holes of tooth or inserts metallic pin in the internal hole of tooth and verifying this newly-provided method. In case of acetal gears, amount of friction-wear is observed to increase by development of plastic deformation and increase of tooth stiffness due to brittle material property of acetal. To the contrary, in case of nylon gears, suggested method is shown to drop down the tooth temperature for about 3∼10$^{\circ}C$ than original gear, thus amount of wear is reduced by over 30% and operating lift prolonged by more than 200%. Hence, suggested method is proved to be practically applicable to the plastic gears made by soft polymers such as Nylon.

• Journal of Applied Reliability
• /
• v.7 no.4
• /
• pp.173-181
• /
• 2007

Out door exposure to daylight and weather climate conditions can cause adverse effect on the properties of automotive plastic materials. The effects of sunlight exposure, especially ultra violet (UV) radiation, can break down the chemical bonds in a polymeric material. This degradation process is called photo-degradation and ultimately leads to color changes, cracking, chalking, the loss of physical properties and deterioration of other properties. To explore the effect of sunlight exposure on the automotive materials, this study investigated photo-oxidation degree and surface property change of molding parts by analytical methods. For the further study, accelerated weathering test methods are proposed, which can correlate with out door weathering, to predict long term performance of automotive plastic materials.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.2
• /
• pp.69-75
• /
• 2009

This study is analyzed by impact simulation according to material property at terminal case of hand phone. Maximum equivalent stress or strain at plastic is 40 times as great as that at magnesium alloy. And the next greatest stress or strain is shown at aluminium alloy. The value of maximum equivalent stress is shown as 6.5 Mpa in case of plastic, magnesium alloy and aluminium alloy. Maximum shear strain at plastic is 40 times as great as that at magnesium alloy. And the next greatest strain is shown at aluminium alloy. The value of deformation or strain at magnesium alloy and aluminium alloy is not different.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.11
• /
• pp.84-90
• /
• 2007

In this study, design and manufacturing of plastic injection mold with cavity pressure/temperature sensors were performed fur tensile test specimen. International standard system for plastic tensile specimen was applied to design an injection molding system. Cavity pressure and temperature sensors were placed on the side of fixed platen of the injection mold to prevent them from external impact damage. Injection molding experiments with variations of injection speed and melt temperature were performed and then tensile test of the manufactured polycarbonate specimens was also performed. It was shown that injection molding processing parameters can have effect on the mechanical properties of the plastic injection molded part.

• Journal of Information Display
• /
• v.9 no.4
• /
• pp.6-10
• /
• 2008

In this study, the selective-wettability-inscription (SWI) technique for the wet-etchingless fabrication of surface microstructures applicable to wide-viewing liquid crystal displays (LCDs) on plastic substrates was demonstrated. On the basis of the selective wetting of the photopolymer, the bi-level microstructures were spontaneously formed to serve as spacers for maintaining uniform cell gap and protrusions for the generation of multi-domains. The LC cell that has bi-level microstructures shows good extinction in the field-off state and a wide-viewing property in the field-on state. The SWI technique would be useful for the fabrication of flexible displays on plastic substrates.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.53-56
• /
• 2004

The mechanical properties and optical micrographs are studied for rolled magnesium alloy sheet with hexagonal close packed structure(HCP) at room and elevated temperatures. Tensile properties such as tensile strength, elongation, R-value and n-value are also measured for AZ31 magnesium alloy. Magnesium with strong texture of basal plane parallel to the rolling direction usually has high R-value and plastic anisotropy at room temperature. As temperature increases, the R-value for AZ31 magnesium sheet decreases. In addition, the AZ31 sheet becomes isotropy and recrystallization above $200^{\circ}C$. Formability of magnesium alloy sheets remarkably poor at room temperature is improved by increasing temperature. Sheet forming of magnesium alloy is practically possible only at high temperature range where plastic anisotropy disappears.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.988-990
• /
• 2003

A plastic substrate for flexible display is developed. The developed PES film has good resistance to heat, low intrinsic birefringence, and mechanical stability. The gas barrier property in the substrate is improved through depositing organic and inorganic multi layer on plastic film by PVD and CVD process.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.11a
• /
• pp.89-94
• /
• 2011

In this research, among thermoplasticity plastic raw material that recycling is possible polyolefine(TPO) and polyvinyl chloride(PVC) as target recycling plan examine wish to. It is polyolefine(TPO) and polyvinyl chloride(PVC)) is mediocrity material that there are a lot of amount useds among plastic material and it is material that recycling is also activated most. Long term made first new regulation raw material, by-product raw material happened at process of production at second factory and third time to examine recycling plan of this material divides this as raw material that pass through process separation and pelet Tuesday and analyzed each special quality removing each removed waste after is used. Measure tension strength and ext. heightening gradually mixing proportion of refreshing resources on standard Sample manufactured as new raw material and application examined possibility availability to single fly system.

• Geotechnical Engineering
• /
• v.13 no.5
• /
• pp.133-144
• /
• 1997

It was proved from the viscosity test for deposits of debris flows(Kim and Seo, 1997) that the property of debris flows could be represented as Bingham plastic model. Based on this bahavior, numerical analysis for the movement of debris flows is carried out by using a computer progran Polyflow which huts been developed for the analysis of the behavior of non-Newtonian fluid. The numerical results obtained from two sites agree well with the movement predicted by an empirical formula. It can be concluded, therefore. that this scheme can be used for the analysis of the movement of debris flow.