• Journal of Powder Materials
• /
• v.31 no.1
• /
• pp.23-29
• /
• 2024

This study investigates the effect of the microstructure of Li_1.3Al_0.3Ti_1.7(PO₄)₃ (LATP), a solid electrolyte, on its ionic conductivity. Solid electrolytes, a key component in electrochemical energy storage devices such as batteries, differ from traditional liquid electrolytes by utilizing solid-state ionic conductors. LATP, characterized by its NASICON structure, facilitates rapid lithium-ion movement and exhibits relatively high ionic conductivity, chemical stability, and good electrochemical compatibility. In this study, the microstructure and ionic conductivity of LATP specimens sintered at 850, 900, and 950℃ for various sintering times are analyzed. The results indicate that the changes in the microstructure due to sintering temperature and time significantly affect ionic conductivity. Notably, the specimens sintered at 900℃ for 30 min exhibit high ionic conductivity. This study presents a method to optimize the ionic conductivity of LATP. Additionally, it underscores the need for a deeper understanding of the Li-ion diffusion mechanism and quantitative microstructure analysis.

• Journal of the Korean Vacuum Society
• /
• v.17 no.6
• /
• pp.495-500
• /
• 2008

The amount of vapor mercury for the generation of glow discharge plasma has been calculated in a fine tube fluorescent lamp having a mixed gas of Ne+Ar including a mercury. When the ionization of atom is considered by the collision between neutral atoms (Ne, Ar, Hg) and electrons of energy $kT_e{\sim}1\;eV$, the density of vapor mercury atom has been obtained as $n(Hg){\sim}3.43{\times}10^{22}m^{-3}$ for the plasma density $n_o{\sim}10^{17}m^{-3}$. In the fluorescent lamps of out diameter 4 mm used for $32{\sim}42$-inch LCD-TVs having a mixture gas of Ne(95%)+Ar(5%) with the pressure of 50 Torr, the quantity of vapor mercury for the glow discharge has been caculated as 0.02{\sim}0.08\;mg$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.111.1-111.1
• /
• 2011

The solar energy is dramatically increasing as the alternative energy source and the silicon(Si) solar cell are used the most. In this study, the improved process and equipment for the metallurgical refinement of multicrystalline Si were evaluated for the inexpensive solar cell. The planar plane and columnar dendrite aheadof the liquid-solid interface position caused the superior segregation of impurities from the Si. The solidification rate and thermal gradient determined the shape of dendrite in solidified Si matrix solidified by the directional solidification(DS) method. To simulate this equipment, the commercial software, PROCAST, was used to solve the solidification rate and thermal gradient. Si was vertically solidified by the DS system with Stober process and up-graded metallurgical grade or metallurgical grade Si was used as the feedstock. The inductively coupled plasma mass spectrometry (ICP) was used to measure the concentration of impurities in the refined Si ingot. According to the result of ICP and simulation, the high thermal gradient between the two phases wasable to increase the solidification rate under the identical level of refinement. Also, the separating heating zone equipped with the melting and solidification zone was effective to maintain the high thermal gradient during the solidification.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.229-237
• /
• 1996

The superconducting phase, $YBa_{2}Cu_{3}O_{x}$ (YBCO), was in-situ deposited on the single crystal MgO substrates, using an aerosol decomposition process in a cold plasma reactor. The solubility and decomposition temperature of the chemical precursors, and the vapor pressures of the solvents, were determined to be the factors crucial to achieving a stoichiometric, crystalline YBCO phase. The deposition parameters for the YBCO phase were 0.3 to 2.7 kPa for the oxygen partial pressure and $800^{\circ}C$ to $940^{\circ}C$ for the substrate temperature. The optimum deposition conditions for the YBCO phase were observed along the CuO decomposition line.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.143-146
• /
• 2003

Al doped Zinc Oxide(ZnO:Al) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors, were prepared by using the capacitively coupled DC magnetron sputtering method. The influence of the substrate temperature, working gas pressure and discharge power on the electrical, optical and morphological properties were investigated experimentally. The consideration on the effect of doping amounts of Al on the electrical and optical properties of ZnO thin film were also carried out. ZnO:Al films with the optimum growth conditions showed resistivity of $9.42{\times}10^{-4}\;{\Omeg}-cm$ and transmittance of 90.88% for 840nm in film thickness in the wavelength range of the visible spectrum.

• Journal of Pharmaceutical Investigation
• /
• v.22 no.1
• /
• pp.49-54
• /
• 1992

This study was carried out for the purpose of developing an effective temazepam soft elastic gelatin capsule (softgel) which exhibits an excellent bioavailability and of comparing the rate and extent of absorption of temazepam from the marked elixir and prepared softgel using hydrophilic liquid such as polyethylene glycol 400 as a suspending agent by rotary die method. Both softgel and elixir containing 3 mg of temazepam were given to 7 healthy male New Zealand White rabbits in a single oral dose cross-over study. Plasma temazepam concentrations were measured by HPLC. The mean peak concentrations of temazepam following a single oral dosing as softgel and elixir dosage form were 13.84 and 13.25 ng/ml, respectively. And the mean time to peak concentration was 1.29 hr for the softgel and 1.07 hr for the elixir. There was no significant difference in the extent of drug absorption (AUC) for the two different dosage froms (p>0.05). While the softgel exhibited mean lag time of 0.63 hr, the elixir did not show any lag time. Statistical moment parameters such as the mean residence time and variance of the mean residence time did not differ significantly for the two formulations.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.7-11
• /
• 2012

Plasma electrolytic oxidation of magnesium alloys is a well known technique to produce corrosion and wear resistant coatings. The addition of particles to the electrolyte provides a possibility to produce coatings with an increasing range of composition by in-situ incorporation of those particles into the coating. An extensive literature review has revealed that the mode of incorporation depends mainly on the melting point of the used particles and the energy provided by the discharges of the PEO process. The spectrum ranges from inert to partly reactive incorporation, but a complete reactive incorporation and a formation of a new single phase coating was not observed so far. Thus a new approach in PEO processing is introduced using specific particles as a kind of sintering additive, changing not only the composition but lowering the melting temperature and increase the liquid phase fraction during the discharges, resulting in a new amorphous coating.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.408-411
• /
• 2003

Al doped Zinc Oxide(ZnO:Al) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors, were prepared by using the capacitively coupled DC magnetron sputtering method. The influence of the substrate temperature, working gas pressure, discharge power and doping amounts of Al on the electrical, optical and morphological properties were investigated experimentally. The effect of bias voltage on the electrical properties of ZnO thin film were also studied. Films with lowest resistivity of $5.4{\times}10^{-4}\;{\Omega}-cm$ have been achieved in case of films deposited at 1mtorr, $400^{\circ}C$ with a substrate bias of +10V for 840nm in film thickness.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.231-236
• /
• 2004

The area of flat glass panel displays such as LCD (Liquid crystal display) and PDP (Plasma display panel) has been increased more than 2 $\times$ 2 m$^2$ for productivity improvement. However, such a large panel area incurs large panel deflection during panel transfer using robots or AGV (Automated guided vehicle) systems. Therefore, electronic industries are making an effort to find an alternative transfer system for the large glass panels with small deflection. The air conveyor with porous pads is one plausible solution, but it becomes expensive because the large porous pads cost much and air consumption increases as the panel area increases. In this work, a simple air slit levitating conveyor was devised to lower the equipment cost and to reduce the air consumption of system. The air flow model between the LCD glass panel and conveyor was constructed and its validity was verified by experiments. To minimize the air consumption, the conveyor dimensions were optimized, and the air consumptions between the air conveyors with the air slit and that with the porous pad were compared.

• Journal of the Korean Vacuum Society
• /
• v.6 no.4
• /
• pp.321-325
• /
• 1997

Recently, photosensitive color filters have received much attention for their use in the liquid crystal display (LCD) industry. It is well known that chemical and physical properties of polymer surfaces can be modified by special surface treatments. In this work, we have studied the polymer surfaces of LCD blue color filters which were exposed to the UV light during photolithography. A better understanding of the irradiated polymer surfaces is required for the subsequent processes such as plasma etching, ITO electrode deposition, etc. The surface analysis has been undertaken using secondary ion mass spectrometry (SIMS), x-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM). A significant enrichment of the pigment component and roughening of surface with bubble-like feature have been observed at the modified polymer surface.