• Journal of the Optical Society of Korea
• /
• v.13 no.1
• /
• pp.22-27
• /
• 2009

Target design study to improve the quality of an accelerated proton beam from the interaction of a high-intensity short pulse laser with an overdense plasma slab has been accomplished by using a two-dimensional, fully electromagnetic and relativistic particle-in-cell (PIC) simulation. The target consists of a thin core part and a thick peripheral part of equivalent plasma densities, while the ratio of the radius of the core part to the laser spot size, and the position of the peripheral part relative to the fixed core part were varied. The positive effects of this core-peripheral target structure could be expected from the knowledge of the typical target normal sheath acceleration (TNSA) mechanism in a laser-plasma interaction, and were apparently evidenced from the comparison with the case of a conventional simple planar target and the case of the transversal size reduction of the simple planar target. Improvements of the beam qualities including the collimation, the forward directionality, and the beam divergence were verified by detailed analysis of relativistic momentum, angular directionality, and the spatial density map of the accelerated protons.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.195-197
• /
• 1993

In this paper, a planar vibratory gyroscope is designed and fabricated in macro model. Elementary experiment and test are done for micro model. This gyroscope has a double gimbal structure with an active dimension $80{\times}120{\times}1\;mm^3$. Outer gimbal vibration is generated by electromagnetic force using ferrite E-core wounded by coil. Inner gimbal vibration is detected by inductive sensor. It is demonstrated' that mechanical and electrical symmetries are important for improvement of vibratory gyroscope.

• Journal of the Korean Magnetics Society
• /
• v.12 no.3
• /
• pp.109-116
• /
• 2002

We designed the flyback planar transformer, which had 8 W capacity, with 70 V input voltage and 8.2 V output voltage for the establishment of design method and the confirmation of application possibility. The numerical value of inductance measured under the switching frequency of 120 kHz was 1650 $\mu$H, which was the inductance efficiency of'85∼87% against theoretical value. The A.C. resistance of primary and secondary coil was 4.2 Ω and 0.25 Ω respectively, On the other hand, the quality factor for each wound numbers showed quite a high value of 158 and 75 respectively. And the Coupling Factor was 0.96∼0.97 under 120 kHz switching frequency. The inductance rapidly increased as the thickness of the core plane increased until it became 1.4 mm but under the thickness more than 1.4 mm, there was no substantial change. Therefore, the critical value of the plane thickness of core was 1.4 mm. And the shape of the output wave of the planar transformer at 70V input voltage was a stable square wave.

• Journal of the Korean Ceramic Society
• /
• v.37 no.6
• /
• pp.524-529
• /
• 2000

Silica slab wavegudie was fabricated on Si substrates by FHD for planar optical passive devices. The slab waveguide consists of lower clad and core layers, where core layer index is controlled by GeO2 addition. Doping of GeO2 in silica is difficult because of the low deposition density due to nonspherical particle generation in FHD process. Silica core particles deposited at various conditions such as flame temperature and substrate scanning were analyzed by SEM and TEM. As the flame temperature increased, the surface roughness of the core layer was decreased up to 3.6 nm after consolidation. Index difference and thickness of core of slab waveguide were 0.3%, 8$\mu\textrm{m}$ respectively. Measured optical loss at TE mode was <0.04 dB/cm at 1.3$\mu\textrm{m}$ and <0.06 dB/cm at 1.55$\mu\textrm{m}$.

• Electrical & Electronic Materials
• /
• v.10 no.8
• /
• pp.813-818
• /
• 1997

In this study the thin film air core and magnetic core inductors consisting of planar coil and/or CoNbZr amorphous magnetic layers on a Si substrate were fabricated as spiral type by using rf magnetron sputtering and wet etching methods. The etchant solution was achieved by iron chloride solution(17.5 mol%) mixed with HF (20 mol%) during 150 sec which etched Cu films and CoNbZr/Cu/CoNbZr multi-layer films. They were about 10${\mu}{\textrm}{m}$ of thickness and 10$\times$10 mm$^2$of size. The properties of thin film magnetic core inductor were 400 nH of Q value at 10 MHz and the resonance frequency was about 300 MHz.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.28-33
• /
• 2004

An in-line fiber coupler, based on side-polished single-mode fibers covered with an intermediate coupling layer and a planar waveguide, is analyzed by modeling the interaction region as an equivalent multi-layered planar waveguide. The reflectance for the multi-layered structure with and without buffer layer is illustrated as a function of the refractive index and thickness of the overlay waveguides. When the refractive index of the overlay waveguides is greater than that of the fiber core, the conditions for the intermediate coupling layer to increase the power coupling from the fiber to the overlays is also explained. Through the experimental results using a LiNbO$_3$planar waveguide, we show that the theoretical analysis is reasonable and in good agreement with the measured values.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.4
• /
• pp.379-384
• /
• 1992

The Fe-base amorphous ribbons with 15mm width and about 20x10S0-6Tm thickness, (FeS179-xTCrS1xT)BS116TSiS15T and (FeS181-xTMnS1xT) BS112TSiS17T (x:0-6), were prepared melt spinner. The thickness of the ribbons followed by PFC (Planar Flow Casting). The initial permeability and total core losses were measured as a function of additive elements (Cr, Mn) and annealing conditions in high frequency for the purpose of using these materials as a core of magnetic amplifier and switched mode power supplies. The initial permeabilities were enhanced and core losses were decreased by non-magnetic field annealing in proper conditions. The lowest core loss in 0.2T/10kHz was measured at 3% Cr addition amorphous ribbon, and the loss was 5.6W/kg. The permeability of the ribbon at 10kHz was about 9000.

• Journal of the Korean Magnetics Society
• /
• v.25 no.1
• /
• pp.4-9
• /
• 2015

This study was carried out to investigate a influence of humidity variation (%) on the magnetic properties and the surface flaws in the fabrication of Fe-based $Fe_{78}Si_9B_{13}$ amorphous alloy ribbon by Planar Flow Casting process. As a result, the size of the air pocket and the droplet which is observed in the contact surface and the free face of the amorphous alloy ribbon becomes large when the humidity increases and the size highly increases with the surface roughness at the same time. Especially, the surface roughness value which is made in the 65 % of the humidity is the lowest in the contact surface ($Ra=0.60{\mu}m$, $Rz=3.11{\mu}m$) and the free face ($Ra=0.47{\mu}m$, $Rz=3.00{\mu}m$). Also, in case of the soft magnetic property of the magnetic core which is made with the toroidal core of $23(OD)^*20(ID)^*20(H)$ size, in the sample of the amorphous alloy ribbon which is made in 65% of the humidity, the most excellent value is gained as $B_s(B_{700})=1.055T$, $H_c=0.083Oe$, permeability = 1,197 and core loss = 0.276W/kg.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.9
• /
• pp.918-926
• /
• 1992

In this paper, ferrite-core loop antenna for portable radio receiver is designed and its characteristics are analyzed. Antenna is fabricated by inserting the ferrite core inside the planar conductor loop$(10{\times}6{\times}15mm^3)$. Bandwidth and Q factor of fabricated antenna measure 0.55 MHz and 280, respectively. These results show remarkable enhancement compared to the conventional loop antenna having the same physical dimension(BW=1.9MHz, Q=8.14). Experimental results show that the relative gain of the fabricated antenna is about 11 dB higher than that of the conventional antenna.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.223-223
• /
• 2009

In this paper, designed and simulated Power Splitter (PS) integrated Mach-Zehnder interferometer (MZI) based planar type optical waveguide devices (which is called here a PS-MZI). The PS-MZI optical waveguide sensor was preceded by a Y-junction, which splits the input power between the sensor, and a reference branch, to minimize the effect of optical power variations. The PS-MZI optical waveguide sensor induced changing phases of the incident beam, which had fallen upon the waveguide through computer simulation, according to the small changes in the index of refraction, thus beam intensity was changed. The waveguide were optimized at a wavelength of 1550 nm and fabricated according to the design rule of 0.45 delta%, which is the difference of refractive index between the core and clad. The fabrication of PS-MZI optical waveguide sensor was performed by a conventional planar lightwave circuit (PLC) fabrication process. The PS-MZI optical waveguide that was fabricated to be applied as a biosensor revealed a low insertion loss and a low polarization-dependent loss. After having etched the over-clad at the sensor part in the MZI optical waveguide that was fabricated, Ti deposition was made on the adhesion layer, and then Au thin-film deposition was carried out thereon. In addition, its optical properties were measured by having changed the index of refraction oil at the sensing part of the MZI. To apply the planar type PS-MZI optical waveguide as a biosensor, a detection test for Staphylococcus aureus was conducted according to changes in concentration, having adopted Ti-alkoxide as ligand. The detection result of the S. aureus by the PS-MZI optical waveguide sensor was possible to the level of $10^1$ CFU/ml.