Dry sliding wear behavior of low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the dual phase steel was compared with that of a plain carbon steel which was normalized at $950^{\circ}C$ for 30min and then air-cooled. Dry sliding wear tests were carried out using a pin-on-disk type tester at various loads of 1N to 10N under a constant sliding speed condition of 0.2m/sec against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss measured to the accuracy of $10^{-5}g$ by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and a profilomter. Micro vickers hardness values of the cross section of worn surface were measured to analyze strain hardening behavior underneath the wearing surfaces. The were rate of the dual phase steel was lower than the plain carbon steel. Oxidation on the sliding surface and strain hardening were attributed for the higher wear resistance of the dual phase steel.
Purpose: The present study examined the reproducibility of an operation plan by comparing the jaw position of STO with the postoperative mandibular set back measurement in sagittal split ramus osteotomy. Methods: Thirty patients with class III dental and skeletal malocclusion and who were treated with BSSRO were reviewed. Three plain radiographs such as the panoramic view, the lateral cephalogram and the submentovertex view were taken before and after operation. Also, paper surgery for STO and model surgery were used to evaluate the amount of mandibular set back. Results: On the panoramic view, the amount of mandibular set back in STO was similar to the postoperative results of model surgery, but the amount of mandibular set back on the lateral cephalogram was smaller than the postoperative result of model surgery and then the amount of set back on submentovertex view was similar to the postoperative result of model surgery. Conclusion: Precise tracing and paper surgery should be performed for a combined expected STO in order to predict the exact amount of preoperative mandibular set back.
Sen, Saduman;Usta, Metin;Bindal, Cuma;UciSik, A.Hikmet
The Korean Journal of Ceramics
/
제6권1호
/
pp.27-31
/
2000
A series experiments were performed to evaluate mechanical behavior of non-oxide boride type ceramics formed on the AISI 1040 plain carbon steel. Boronizing was performed in a slurry salt bath consisting of borax, boric acid, and ferro-silicon at $950^{\circ}C$ for 2-6h. The AISI 1040 steel used as substrate material was containing 0.4%C, 0.13%Si, 0.65%Mn, 0.02%P, 0.014%S. The presence of non-oxide boride type ceramics $Fe_2B $ and FeB formed on the surface of steel was confirmed by metallographic technique and X-ray diffraction (XRD) analysis. The hardness of borides measured via Vickers indenter with a load of 2N reached a microhardness of up to 1800 DPN. The hardness of unborided steel was 185 DPN. The fracture toughness of borides measured by means of Vickers indenter with a load of 10N was about 2.30 MPa.$m^{1/2}$. The thickness of boride layers ranged from 72$\mu\textrm{m}$ to 145$\mu\textrm{m}$. Boride layers have a columnar morphology.
본 연구에서는 CFRP로 보강한 2방향 콘크리트의 정하중 및 저속 충격하중에 대한 실험을 수행하였다. 압축강도 40MPa의 콘크리트 및 이와 동일한 배합에 0.75%의 강섬유를 혼입한 강섬유 보강 콘크리트로 $50{\times}350{\tims}350mm$의 부재를 제작하여 CFRP로 보강하였다. CFRP와 강섬유로 보강한 시험체는 콘크리트가 쪼개지는 파괴와 펀칭 파괴가 복합적으로 나타나고, 이 때 쪼갬 균열 수는 보강하지 않은 콘크리트에 비해 확연하게 줄어들었다. CFRP와 강섬유로 동시에 보강한 시편은 충격하중 하에서 2방향 콘크리트 시험체가 파괴되는 데에 6.8배의 에너지가 소모되었다.
In this study, condensation heat transfer coefficients(HTCs) of CFC-11, HCFC-123 and HCFC-141b are measured, which are used/or considered as working fluids in centrifugal chillers. The main objectives of this study are to measure and compare the HTCs of various refrigerants on plain and low fin tubes and also to find out the optimum fin density of the low fin tubes. To accomplish these goals, HTCs of three refrigerants are measured for the plain tube as well as 4 types of low fin tubes. All measurements are carried out at the vapor temperature of 39.deg. C with the wall temperature difference of 3 .deg. C ~ 8.deg. C. For all the refrigerants tested, a low fin tube of 28 fins per inch yielded the best performance among all the tubes tested. For the plain tube, the HTCs of CFC-11 and HCFC-141b were very similar and those of HCFC-123 were 10% lower than those of CFC-11.Thus, it can be concluded that HCFC-123 and HCFC-141b are acceptable as alternative refrigerants for CFC-11 from the view point of condensation heat transfer.
This study is about the fabric attached to the relics excavated from the Shimchun-ri tomb of the 4th century and the Moonsan-ri tombs of the 5th century. We studied 5 pieces of fabric from the Shimchun-ri tomb: one piece was silk and the other four pieces were hemp. We were able to observe 8 pieces from the four tombs in Moonsan-ri, All of them except one ramie were silk. The two kinds of bast fiber found in the tombs of Shimchun-ri and Moonsan-ri were hemp and ramie, and they were found to be plain woven with S-twist thread which thickness is uneven. The density was more fine compared to the hemps found in the Kaya or Shinra tombs of the similar era. All of the silk textiles found in the Shimchun-ri and Moonsan-ri tombs used non-twisted thread, and were plain woven. Also, we found degummed and raw silk from the tombs. The average density of the silk textiles from these tombs are similar to other areas of the same time, and studies show that they used non-twisted thread in plain woven silk found in other tombs. Therefore, we can conclude that they usually used non-twisted thread when producing silk textiles.
Woven fabrics composites are used as primary structural components in many applications because of their superior properties that offer high specific strength and stiffness. However, the complexity of the fabric structure makes understanding of their failure behavior very difficult. Also, laminate woven fabrics CFRP have unique failure mechanisms such as fiber bridging, fiber/matrix crack and so on. In particular, the delamination phenomenon of the composite materials is one of the most frequent failure mechanisms. So, we estimated interlaminar fracture and damage in composites using as ENF specimen by a 3 point bending test. And AE characteristics were examined for crack propagation on plain woven CFRP. We obtained the following conclusions from the results of the evaluation of the 3 point bending fracture test and AE characteristic estimation. AE counts of maximum crack length were obtained as $85.97{\times}10^4\;and\;93{\times}10^3\;for\;a_0/L=0.3$ and 0.6, respectively. Also the maximum amplitudes were over 80dB at both $a_0/L=0.3\;and\;0.6$. $G_{IIc}$ at that's $a_0/L$ ratio were obtained with $1.07kJ/m^2\;and\;3.79kJ/m^2$.
Land reform in Korea was performed in 1949. The formation of owner farmers was the primary objective of land reform. But since land reform, the number of tenants has been increasing, and it reached to 65.7% of total farmhousehold by 1985. To analyze the productivity of tenant farming, 40 farmers in Kumnam, Yeongi Gun and Gongju Gun, Banpo, Chungnam Province, were selected as samples for the empirical analysis. The results of the empirical analysis are summarized as follows; 1. In plain area, tenants input 5% more labor, and 15% less capital than owner farmers. In mountain area, tenants input 15% more labor, and 4% more capital than owner farmers. 2. There is no difference in the output of rice between owner farmers and tenants in both area. 3. In plain area, the physical productivity of labor of owner farmers is 4.6 (kg/hour), and that of tenants is 4.4. And the physical productivity of labor of owner farmers in mountain area is 4.2, and that of tenants is 3.6. 4. The physical productivity of capital of owner farmers in plain area is 17.7(kg/1,000 won), and that of tenants is 20.6. In mountain area, the physical productivity of capital of owner farmers is 18.8, and that of tenants is 17.9.
The principal objective of this study was to determine the optimal mixing conditions of three different amounts of small black soybeans, sugar, and plain yogurt, for the preparation of a small black soybean smoothie. The experimental design utilized herein was based on the Central composite design methodology of response surface, which included 16 experimental points, including 2 replicates for the small black soybeans, sugar, and plain yogurt. The physiochemical and sensory properties of the test were measured, and these values were applied to the mathematical models. A canonical form and perturbation plot showed the influence of each ingredient on the mixed final product. The L value and a value decreased with increasing quantities of small black soybeans, but the b values increased with greater additions of small black soybeans. Sweetness increased with increasing amount of added sugar. The results of sensory evaluation showed very significant values for color (p<0.01), taste (p<0.05) and overall quality (p<0.05) in the predicted model. As a result, the optimum formulations by numerical and graphical methods were calculated as follows: small black soybean 79.46 g, plain yogurt 275.07 g, sugar 21.20 g.
본 논문에서는 평직복합재료의 섬유다발의 배열 및 적층수가 등가물성치에 미치는 영향을 연구하였다. 임의로 적층된 2~32장의 평직복합재료 구조물의 단위구조를 모델링 하였고, 단위구조의 외부 경계 면에는 반복 경계조건을 가하였다. 등가물성치는 일축 인장시험 및 전단시험을 수치적으로 모사하여 계산하였고, 섬유다발 위상차의 무작위적 특성은 표본해석을 통해 고려하였다. 계산 된 등가물성치의 통계처리 결과, 두께가 얇은 평직복합재료의 $E_{xx}$와 $V_{xy}$는 위상차의 영향을 크게 받았고, 넓은 빈도분포를 보였다. 그러나 적층수가 증가함에 따라 분포의 폭은 감소하였고 평균값은 일정한 값으로 수렴하였다. 반면에, 섬유다발의 면내 방향으로의 이동 및 적층수의 변화는 $G_{xy}$에 거의 영향을 미치지 않는 것으로 나타났다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.