• 오토저널
• /
• 제6권2호
• /
• pp.39-46
• /
• 1984

There are various ringshaped automotive and machine parts and the study about the characteristics of ring are the important basis of the quality control and performance improvement of outer race of ball bearing, railwheel, ring gear, piston ring, and other ringshaped seals, etc. In this study, the effect of prestress which arise inevitably during the fitting of the ring shape parts and the effect of central line extension/contraction on the vibrational characteristics of ring are verified. Although many studies are made on the vibration of ring, the study about prestress and extension were rather scarce and rare. As a result of the study, a series of frequency formulas are derived. The result of this study can be utilized in the improvement of design as well as in the quality control during the fitting work.

• Elastomers and Composites
• /
• 제30권3호
• /
• pp.235-246
• /
• 1995

When an O-ring is installed in a high fluid pressure device, a section of the O-ring is extruded into the piston-cylinder clearance gap. Any tendency towards extrusion will induce wear in dynamic applications, leading to premature failure of the seal. In this study, the mechanism of initial extrusion of the O-ring was studied, 1.e., how much amount of the O-ring will be extruded into the clearance gap at a certain pressure. The relationship between extrusion depth and a clearance gap or fluid pressure were studied by finite element analysis (FEA). After that, Salita's experimental data were analyzed. The result is that Initial extrusion depth for an O-ring into a clearance gap was 1.11 times the product of dimensionless pressure difference $(p-p_1)/E$ and clearance gap c. The required pressure $p_1$ for zero extrusion depth was found to decrease logarithmically with increasing clearance gap.

• 한국주조공학회지
• /
• 제24권3호
• /
• pp.132-137
• /
• 2004

• Tribology and Lubricants
• /
• 제14권4호
• /
• pp.108-113
• /
• 1998

In order to investigate the characteristics of top ring groove deposit formation in diesel engine, engine test and simulation test were performed. From component analysis of used oils sampled from actual running engines, soot content in engine oil was selected as a main parameter for evaluating oil degradation. Deposit formation is highly related to soot content in lubricating oils. And high soot content oil accelerates deposit formation even in low temperature region below 26$0^{\circ}C$. In low temperature region below 26$0^{\circ}C$, deposit formation rate is mainly affected by top ring groove temperature. However, in high temperature region above 26$0^{\circ}C$, deposit formation rate is affected by soot content as well as top ring groove temperature. Therefore, soot content as well as top ring groove temperature should be kept a certain level in order to prevent troubles due to carbon deposit formation.

• 한국자동차공학회논문집
• /
• 제4권1호
• /
• pp.75-85
• /
• 1996

The gas pressure acting on the rings in internal combustion engine influences the friction, wear and HC emission. In order to understand their characteristics, it is necessary to measure the interring gas pressure during engine operations. In this study, miniature type pressure transducer was developed to measure inter-ring gas pressure. And measurements of cylinder and inter-ring gas pressure were made on a gasoline engine running at full and part load conditions. Finally the characteristics of inter-ring gas pressure variation during engine operation were obtained form analysis of measured date.

• Journal of Mechanical Science and Technology
• /
• 제17권6호
• /
• pp.888-895
• /
• 2003

Combustion chamber crevices in SI engines are identified as the largest contributors to the engine-out hydrocarbon emissions. The largest crevice is the piston ring-pack crevice. A numerical simulation method was developed, which would allow to predict and understand the oxidation process of piston crevice hydrocarbons. A computational mesh with a moving grid to represent the piston motion was built and a 4-step oxidation model involving seven species was used. The sixteen coefficients in the rate expressions of 4-step oxidation model are optimized based on the results from a study on the detailed chemical kinetic mechanism of oxidation in the engine combustion chamber. Propane was used as the fuel in order to eliminate oil layer absorption and the liquid fuel effect. Initial conditions of the burned gas temperature and in-cylinder pressure were obtained from the 2-zone cycle simulation model. And the simulation was carried out from the end of combustion to the exhaust valve opening for various engine speeds, loads, equivalence ratios and crevice volumes. The total hydrocarbon (THC) oxidation in the crevice during the expansion stroke was 54.9% at 1500 rpm and 0.4 bar (warmed-up condition). The oxidation rate increased at high loads, high swirl ratios, and near stoichiometric conditions. As the crevice volume increased, the amount of unburned HC left at EVO (Exhaust Valve Opening) increased slightly.

• 자원환경지질
• /
• 제54권1호
• /
• pp.35-48
• /
• 2021

구미분지는 영남육괴의 남동 중간부에 있으며 하부로부터 백악기의 구미층, 안산암질암류(영암산응회암, 부상리안산암), 유문암질암류(오봉리응회암, 도선굴유문암, 금오산응회암)와 관입암류(환상암맥, 기타 암맥)로 구성된다. 금오산응회암은 거의 대부분 회류응회암으로 구성되며 환상암맥과 함께 금오산 칼데라와 연관되어있다. 칼데라는 직경이 3.5 × 5.6 km이고 환상암맥과 단층으로 둘러싸인다. 칼데라 내부 화산암층은 유상 및 용결엽리가 대체로 칼데라 연변부에서 안쪽으로 경사되는 하향자루 구조를 나타낸다. 칼데라 블록은 북변부에서 350m, 남변부에서 600m 내려앉은 비대칭 침하를 나타낸다. 이 자료들에 의하면 금오산 칼데라는 하나의 칼데라윤회를 암시하는 기하학적으로 비대칭 피스톤 침하 칼데라로 분류된다. 이 칼데라는 챔버로부터 마그마의 대규모 분출에 뒤따라 외측경사 환상단층으로 경계되는 칼데라 블록의 피스톤 침하를 지시한다. 칼데라 블록에서 하향자루는 경계 단층의 완전한 발달과 동시에 초기 침하동안 하향자루운동을 의미한다. 이 운동에 의한 벌어진 환상열극에는 침하에 따른 마그마 과압으로 인해 마그마가 주입되어 환상암맥을 형성하였다.

• 한국자동차공학회논문집
• /
• 제18권3호
• /
• pp.95-103
• /
• 2010

This paper presents a simulation model of a double-acting high-speed pneumatic cylinder with a relief valve type cushion mechanism. The model predicts piston motion, mass flow rate, pressure and temperature time histories of cushion chamber. Of interest here is to investigate the cushioning effect of varying the piston and piston-rod diameter, cushion ring diameter and length, and stoke in cushion mechanism. As a result, this cushion mechanism is found to be adequate under high-speed driving of pneumatic cylinders. The simulation model proposed here will be very useful to analyze the dynamic characteristics and to improve or design the better cushion mechanism in high-speed pneumatic cushion cylinders.

• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.343-348
• /
• 2008

In this paper, a CFD (Computational fluid dynamics) code, FLUENT is adopted to investigate accurate flow characteristics for a slipper bearing which is used swash plate type hydraulic axial piston pump. Static pressure and velocity distributions, and velocity vectors are plotted for different film thickness and slipper rotational velocity. In recess region, there exists a doughnut shaped vortex ring. The static pressure distributions are non-uniform and the flow fields are highly asymmetrical under bearing rotation. Therefore the numerical method adopted in this paper can be use in design of hydrostatic components and further studies are required.

• 한국수소및신에너지학회논문집
• /
• 제14권2호
• /
• pp.131-137
• /
• 2003

Backfire occurrence must be controlled for the practical use of hydrogen fueled engine. It was found from preceeding studies that crevice volume around piston rings could effect a backfire occurrence. In this study, a possible countermeasure to backfire occurrence was evaluated by using multi point ignition method around piston ring. The results showed that backfire limited equivalence ratio was increased by a little due to a enhancing effect of mixture combustion around piston crevice volume.