• Environmental Analysis Health and Toxicology
• /
• v.15 no.3
• /
• pp.93-98
• /
• 2000

The photosatalytic oxidation of the model compound, 1, 3, 5-trichlorobenzene (1, 3, 5-TCB) has been investigated employing photolysis. The effects of parameters such as illumination time, initial concentration, pH and HA were investigated. Pt(IV)/AMM-Ti particles used as a photocatalyst showed a time-dependent enhancement of the photooxidation/reduction activity in the presence of HA.

• Proceedings of KOSOMES biannual meeting
• /
• 2003.05a
• /
• pp.205-209
• /
• 2003

The various pretreatment processes were evaluated for removal of oil pollutants with weathered oil contaminated seawater in a reverse osmosis desalination process. Weathered oil contaminated seawater was made by biodegradation and photooxidation with oil containing seawater. Coagulation, ultrafiltration, advanced oxidation processes and granular activated carbon filtration was used with pretreatment for dissolved organic carbon. Crude oil was removed but. weathered oil contaminated seawater was not removed by biodegradation and coagulation. DOC and E260 was removed with about 20 % and 40 % by membrane filter of cut off molecular weight 500. So, the most of dissolved organic carbon in weathered oil contaminated seawater was revealed that molecular weight was lower than 500. It is difficult to remove DOC in weathered oil contaminated seawater by advanced oxidation processes treatment, but, E260 was removed more high. However, DOC in weathered oil contaminated seawater was easily adsorbed to GAC. It is revealed that DOC was removed by adsorption.

• Macromolecular Research
• /
• v.10 no.3
• /
• pp.168-173
• /
• 2002

Unstabilized low-density polyethylene (LDPE) films and films formulated with hindered amine light stabilizer (HALS) were exposed to UV-radiation; and the physicochemical changes during photooxidation processes have been investigated using tensile, FTIR spectre-photometric and thermal analytical (DSC) techniques. The dependence of tensile properties (elongation- and stress-at-break), carboxyl index and heat of fusion on UV-irradiation time have been discussed. The use of HALS is found to be effective in maintaining the UV-mechanical properties of the LDPE films. The experimental results showed that there exists no correlation between mechanical properties and carbonyl index, whereas crystallinity correlates well with carbonyl index in unstabilized and stabilized films for irradiation times greater than 100 h. The rate of formation of carbonyl groups is found to be dependent on UV exposure time. Crystallinity of the film samples is strongly influenced by both exposure time and presence of HALS.

• Preventive Nutrition and Food Science
• /
• v.6 no.4
• /
• pp.253-256
• /
• 2001

Irradiation of food is not only used for sanitation purposes but can be used for processing techniques to reduce or eliminate toxic or undesirable compounds on food. Irradiation wag effective to reduce the allergenicity of food by modification of the structure of proteins causing allergy reactions. Volatile N-nitrosmaine was reduced or eliminated by irradiation in the model system study and the breakdown products by irradiation did not recombine under human stomach conditions (pH 2,3, and 4,37$^{\circ}C$). The possibility of residual chlorophyll b reduction by irradiation was also found, and the model study indicated that irradiation be used to destroy chlorophyll b, resulting in protection from photooxidation in oil without acceleration of lipid oxidation during irradiation. In this paper, several on-going research projects for the application of food irradiation as a new processing technique are introduced, including reduction of food allergens, breakdown of volatile N-nitrosamine and residual chlorophyll b.

• Bulletin of the Korean Chemical Society
• /
• v.10 no.1
• /
• pp.57-60
• /
• 1989

UV irradiation of anthraquinone and diphenylacetylene in benzene gave 1:1 photoadduct (7) and cyclization product (8). The photoreaction of anthrone and diphenylacetylene in dichloromethane afforded the photooxidation products (7, 8, and 9) in air. The photoproduct (7) underwent the cyclization reaction during the purification by the column chromatography (silica gel). When irradiated with 350 nm UV light, the product (11) of benzil reacted with diphenylacetylene to give a photoadduct(12).

• Mass Spectrometry Letters
• /
• v.12 no.3
• /
• pp.118-124
• /
• 2021

Many previous studies have focused on revealing the harmfulness of microplastic particles, whereas very few studies have focused on the effects of chemicals, particularly photooxidation product. In this study, products of photodegradation from expanded polystyrene (EPS), compounds produced by photolysis by ultraviolet (UV) light, were investigated. EPS was directly irradiated and photolyzed using a UV lamp, and then the extracted sample was analyzed using high-resolution mass spectrometry (HRMS). Multiple ionization techniques, including electrospray ionization, atmospheric pressure chemical ionization, and atmospheric pressure photoionization, were used. In total, >300 compounds were observed, among which polystyrene monomer, dimer, and oxidized products were observed. In this work, the data presented clearly demonstrate that it is necessary to identify and monitor oxidized plastic compounds and assess their effect on the environment.

• Textile Coloration and Finishing
• /
• v.28 no.2
• /
• pp.63-69
• /
• 2016

Poly(butylene terephthalate)(PBT) surface was modified by UV/ozone irradiation and the effect of UV energy on the surface properties of the irradiated PBT films were characterized by the reflectance, surface roughness, contact angles, ESCA, and ATR analyses of the film surface. The surface reflectance, at the short wavelength of visible spectrum of particularly 400nm, decreased with increasing UV energy. And the irradiation roughened the film surface uniformly in the nano scale. The maximum surface roughness increased from 110nm for the unirradiated sample to 303nm at the UV energy of $10.6J/cm^2$. The surface energy of PBT film increased from $50.5mJ/m^2$ for the unirradiated PBT to $58.8mJ/m^2$ at the irradiation of $21.2J/cm^2$. The improvement in hydrophilicity was caused by the introduction of polar groups containing oxygens such as C-O and C=O bonds resulting in higher $O_{1s}/C_{1s}$. The increased dyeability of the modified film to cationic dyes may be resulted from the photochemically introduced anionic and dipolar dyeing sites on the PBT films surfaces.

• Textile Coloration and Finishing
• /
• v.23 no.4
• /
• pp.284-289
• /
• 2011

Poly(phenylene sulfide)(PPS) films were photooxidized under UV/ozone irradiation. The effect of UV energy on the surface properties of the UV-irradiation PPS films were investigated by the measurement of reflectance, surface roughness, and contact angle. Reflectance decreased at the wavelength of 400nm and the surface roughness increased with increased UV energy. The improvement in hydrophilicity with increased $O_{1s}/C_{1s}$ was caused by the introduction of hydrophilic $SO_2$ bond. Surface energy increased from 46.6 to $78.3mJ/m^2$ with increased UV energy up to $21.2J/cm^2$. Also zeta potential decreased with increased UV energy. The increased dyeability to cationic dyes may be due to the photochemically introduced anionic and dipolar dyeing sites on the PPS films surfaces.he photochemically introduced anionic and dipolar dyeing sites on the PPS films surfaces.

• Journal of Photoscience
• /
• v.10 no.3
• /
• pp.219-223
• /
• 2003

Phloxine B (2,4,5,7-tetrabromo-4,5,6,7-tetrachlorofluorescein disodium salt), also referred as D&C red dye no. 28, is phototoxic to many insects such as Tephritidae fruit flies. Sunlight photolysis of phloxine B in aqueous solutions was a first order kinetic reaction at low concentrations. But it turned to be more complex reactions with the increase of phloxine B concentration. The half-lives of phloxine B (6-120 ${\mu}$M) were 18-41 and 52-289 hours in oxygenated and deaerated distilled water, respectively. The photolysis rate constants increased as the phloxine B concentrations increased. The singlet oxygen formation positively correlated with the concentrations of phloxine B and humic acid in oxygenated distilled water. The formation of singlet oxygen did not stop even after the complete degradation of phloxine B, which suggested an involvement of photoproduct-mediated reactions. The results showed that singlet oxygen mediated photooxidation was a dominant reaction for phloxine B dissipation in an aqueous solution, and the self-sensitized and photoproduct-mediated reactions were also involved at the higher concentrations. Iodide and bromide ions significantly decreased phloxine B photolysis rate constants, which were in relation to the decrease of singlet oxygen formation.

• Journal of Environmental Science International
• /
• v.11 no.1
• /
• pp.85-91
• /
• 2002

The effects of initial concentration of dissolved oxygen content, Cu(II) and EDTA in an aqueous Cu(II)-EDTA solution on $TiO_2$ photo-oxidation of EDTA were investigated using $TiO_2$ (Degussa P-25) and UV irradiation at $20{\circ}C$. In the presence of dissolved oxygen and/or Cu(II) the photo-oxidation rates of EDTA were enhanced. The rates linearly increased in the range of initial Cu(II) concentration below 1.79 mM, while abode this concentration those were kept constant. The trend or the EDTA photo-oxidation rates appeared to be akin to the Langmuir-Hinshelwood equation farm and the k values calculated were 0.05 mM/min for the free-EDTA system, and 0.17 mM/min far the Cu(II)-EDTA system. These meant the aqueous EDTA decomposition was enhanced due to weakening of the intra-molecular bond strength of EDTA by complexation with Cu(II) added. It was concluded the decomposition of aqueous EDTA by $TiO_2$ photo-oxidation was maximum in the presence of dissolved oxygen supplied by air purging and of Cu(II) with its concentration for 1:1 Cu(II)-EDTA complexation ratio.