• Journal of Adhesion and Interface
• /
• v.10 no.4
• /
• pp.191-198
• /
• 2009

UV-curable aliphatic epoxy acrylates were prepared by the reaction of glycerol diglycidyl ether (GDE) with 2-carboxyethyl acrylate (2-CEA) or 2-hydroxyethyl acrylate (2-HEA). The structures of the epoxy acrylates were characterized by FT-IR, $^1H$-NMR, and $^{13}C$-NMR and the yield was obtained by prep-LC. The UV- and the thermal-curing behaviors of the product were investigated using photo-DSC and DSC, respectively. The reactivity of 2-CEA was higher than 2-HEA and the yield of the product (GEA-C) which was prepared using 2-CEA was about 83%. The maximum UV-curing time ($T_{max}$) of the GEA-C contained non-reactive components and by-product was about 10 seconds. The GEA-C showed low color difference (${\Delta}E^*$), low viscosity, and good thermal stability - its value was 2.51, 192 cps, and $299^{\circ}C$ (at 5% weight loss), respectively. The activation energies ($E_a$) of thermal-curing reaction calculated from Kissinger and Ozawa-Flynn-Wall method were 91~92 kJ/mol.

• Polymer(Korea)
• /
• v.39 no.1
• /
• pp.185-190
• /
• 2015

Since a transition from liquid crystal to crystal state is slow for the large photo-reactive liquid crystal molecules, it needs a long time for recrystallization of LC242 molecules when lowering the temperature of the liquid crystal. Although liquid crystals usually align along one direction, the directions of individual liquid crystal molecules are little different from one another with increasing temperature, resulting in changes of birefringence of the liquid crystal films. When the photo-reactive liquid crystals are photo-cured, faster curing kinetics and much larger curing degrees are observed for the films cured at the liquid crystal phase.

• Elastomers and Composites
• /
• v.54 no.4
• /
• pp.359-367
• /
• 2019

Poly(2-hydroxyethyl methacrylate) (PHEMA) hydrogels modified with various co-monomers, such as N-vinyl pyrrolidone (NVP), glycidyl methacrylate (GMA), and glycerol monomethacrylate (GMMA), were prepared to investigate the effect of adding a co-monomer on the water contents, surface wettability, and tensile modulus. These polymers were synthesized by thermal- and photo-polymerization in the presence of azobisisobutyronitrile (AIBN) and diphenyl(2,4,6-trimethylbenzoyl)-phosphineoxide (TPO) as the initiators. The characteristics of the hydrogels were analyzed via FTIR and UV/Vis spectroscopies, contact angle measurements, and tensile modulus measurements with UTM. Regarding the properties of water in the hydrogels, the ratio between free to bound water was investigated using differential scanning calorimetry (DSC). The effects of adding the co-monomers on the water content, surface wettability, and tensile modulus for soft contact lenses were also investigated. In the case of p(HEMA-co-NVP) hydrogels, the increase in the equilibrium water content (EWC) was primarily due to the increase in the bound water content. For p(HEMA-co-GMMA) hydrogels, an increase in free water content was the main reason for the increased EWC. In contrast, in the case of p(HEMA-co-GMA) hydrogels, a decrease in bound water content was observed to be the main factor that reduced the EWC. Photo-polymerized PHEMA hydrogels showed enhanced surface wettability and tensile modulus as compared to those produced via thermal polymerization.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.305-308
• /
• 2007

The field of dye-sensitized solar cell (DSC) is being researched actively at present. Because DSC has several advantages to pass the limits of Si solar cells such as a low manufacturing expense, a simple manufacturing process and its transparency. A lot of researches are underway about materials and processes in the field of dye-sensitized solar cell but its structure has been fixed up as the sandwich structure that both edges are used as positive and negative terminals. But the structure as of present is a factor of decreasing efficiency because the more electrons are recombined the further distance from terminal, considering about the characteristic of dye-sensitized solar cell that electrons generated inside cell are moved by diffusion. In this study, we made experiment on expanding the terminal to shorten internal moving distance of electron and compared the results according to the variation of active area to find out the effect of this trial. As a result, we achieved about 15.5% improvement of maximum power and 0.5% improvement of efficiency from terminal-expanded dye-sensitized solar cell of $2cm^{2}$ active area and concluded that the increasing rate of efficiency is raised as the active area becomes wider.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.04a
• /
• pp.220-224
• /
• 2009

The effect of addition of single and binary additives on the performance of dye-sensitized $TiO_2$ solar cells based on 1,2-dimethyl-3-propylimidazolium iodide (DMPII) in ethylene carbonate (EC) and gamma-butyrolactone (GBL) has been evaluated at different cell temperatures in the $30-120^{\circ}C$ range. The electrolyte containing a single additive, 2-(dimethylamino)-pyridine (DMAP) showed best performance, which showed further enhancement for an electrolyte containing binary additives, DMAP and 5-chloro-1-ethyl-2-methylimidazole (CEMI) in equal molar ratio. The performance of the dye sensitized solar cell (DSC) based on electrolyte containing binary additives were found to be better than an acetonitrile based electrolyte. The dependence of different photovoltaic parameters (Voc, Jsc, ff, n) of the DSC upon temperature has been studied over the $30-120^{\circ}C$ range and only a small decrease in conversion efficiency has been observed. Thus the electrolyte containing binary additives (DMAP, CEMI) in EC/GBL solvent and show better performance in the investigated temperature range ($30-120^{\circ}C$).

• Korean Journal of Materials Research
• /
• v.27 no.4
• /
• pp.199-205
• /
• 2017

In this study, (3,4-epoxycyclohexane)methyl 3,4-epoxycyclohexylcarboxylate acrylate was synthesized by reacting (3,4-epoxycyclohexane)methyl 3,4-epoxycyclohexylcarboxylate with acrylic acid to minimize hardening shrinkage and to improve heat resistance, which are known as disadvantages of photopolymers for 3D printing application. Urethane acrylate was synthesized by reacting 1,3,5-triazine-2,4,6-triamino alcohol, 2-hexylethyl acrylate, and isophorone diisocyanate in order to improve the mechanical properties without deteriorating the heat resistance. The physical properties before and after the synthesis of the acrylate and the mechanical properties when the urethane acrylate was applied were investigated. The reaction progress of the composite was examined by FTIR and $^{13}C$ NMR. The heat deflection temperature, flexural strength, and surface hardness of the molding were measured. The curing behavior by Photo-DSC ultraviolet irradiation was also examined.

• Macromolecular Research
• /
• v.12 no.2
• /
• pp.195-205
• /
• 2004

We have synthesized new aromatic polyesters (DiPEG-HQ and DiPEG-BP) by condensation polymerization of a terephthalic acid derivative bearing a pendant oligo(oxyethylene) (DP = 7, MW = 350), which has a methoxy terminal group, and two different aromatic diols, hydroquinone and 4,4'-biphenoI. The synthesized polymers were characterized by differential scanning calorimetry (DSC), polarizing microscopy, and X-ray diffractometry for their liquid crystallinity (LC), thermal transitions, and structural morphologies in mesophases. The morphology of the LC phases depends strongly on the length of the rigid backbone repeating unit. The DiPEG-BP polymer having a longer repeating unit exhibits both layered and nematic structures before isotropization, whereas the DiPEG-HQ polymer having a shorter repeating unit shows only the layered structure in the mesophase. We found that the layer spacing for DiPEG-HQ is larger than that for DiPEG-BP. Both polymers easily form complexes with LiCF$_3$SO$_3$; we studied this complex formation by FT-IR spectroscopy. The layer spacing of the polymer-electrolyte composites increases upon increasing the amount of the lithium salt. The polymer/salt electrolyte mixtures we investigated at molar ratios of EO:salt in the range of 5-20 exhibit electrical conductivity values at 40$^{\circ}C$ of 2.4${\times}$10$\^$5/ and 1.1${\times}$10$\^$－5/ S/cm for DiPEG-HQ/LiCF$_3$SO$_3$ and DiPEG-BP/LiCF$_3$SO$_3$, respectively. At 80 $^{\circ}C$, these values are higher: 4.6${\times}$10$\^$－3/ and 1.1${\times}$10$\^$－4/ S/cm, respectively. The activation energy of conductivity depends strongly on the salt concentration.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.651-654
• /
• 2009

Novel compounds with rod and disc mesogens were synthesized and characterized. The molecular structures were confirmed by FT-IR, $^1H$-NMR spectroscopy and elemental analysis. The optical properties of these molecules were investigated by UV-vis absorption spectroscopy and photo-luminescence spectroscopy. We found that they are a novel series of blue light-emitting molecules. The absorption spectra peaks of these compounds varied from 336 nm-341 nm, while the maximum emissions centered form 410 nm-450 nm in chloroform solution. However, unexpectedly we could not found their biaxiality and mesomorphic properties by POM, conoscopy and DSC method.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.11a
• /
• pp.97-99
• /
• 2002

유리내부에 수십나노크기의 Ag 금속입자를 생성시키기 위한 연구를 진행하였다. 본 연구에서는 규산염계 유리에 Ag와 Ce을 첨가하여 환원분위기에서 유리를 제조함으로서 Ce$^{3+}$ 를 유리내에 생성시킬 수 있었으며, 또한 레이저조사(irradiation)를 통하여 Ag+이온의 금속입자 환원을 도울 수 있었다. 또한 레이저 조사시간에 따른 금속입자의 변화를 관찰하고자 하였으며, 이와 같은 과정으로 생성된 금속입자함유 유리를 열처리함으로서 나타나는 열적특성을 평가하여 금속입자가 결정화과정에 미치는 영향을 평가하고자 하였다. 유리내에 존재하는 나노금속입자를 투과전자현미경 (TEM)을 통하여 확인하였으며, 시차주사열량분석법(DSC)을 통해 유리의 결정화거동을 평가하였다. 또한 Photo Luminescence 측정을 통한 유리내부의 Ce이온의 전자상태를 관찰하였다.

• Journal of Adhesion and Interface
• /
• v.12 no.2
• /
• pp.47-55
• /
• 2011

UV-curable coatings have been used in various industries due to their advantages such as high mechanical property, good solvent resistance, fast curing process and low volatile organic compounds. However, a lack of flexibility of UV-cured films is a weak point for the pre-coated system of roll-to-roll process. In this study, UV-curable polycarbonate-based methacrylates were synthesized with polycarbonate diol, isophorone diisocyanate and 2-hydroxyethylmethacrylate to improve flexibility of the UC-cured films. The effects of polyol molecular weight, content of photoinitiator and monomers on the UV-curing behavior, flexibility and properties were investigated. The UV-curing behavior was measured by a photo-DSC, the pendulum hardness, tensile strength, viscoelastic properties were also evaluated.