• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.75-82
• /
• 2015

This paper presents a new technique for enhancing power quality by reducing harmonics in the neutral conductor. Three-Phase Four-Wire (3P4W) system is commonly used where single and three phase loads are connected to Point of Common Coupling (PCC). Due to unbalance loads, the 3P4W distribution system becomes unbalance and current flows in the neutral conductor. If loads are non-linear, then the harmonic content of current will flow in neutral conductor. The neutral current that may flow towards transformer neutral point is compensated by using a series active filter. In order to reduce the harmonic content, the series active filter is connected in series with the neutral conductor by which neutral and phase current harmonics are reduced significantly. In this paper, solar PV based inverter circuit is proposed for compensating neutral current harmonics. The simulation is carried out in MATLAB/SIMULINK and also an experimental setup is developed to verify the effectiveness of the proposed method.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.9
• /
• pp.103-109
• /
• 2006

This research is contents about output characteristic of optic current sensor that use faraday effect. optic current sensor used in an experiment is consisted of three parts.(1) Source of light used laser diode of 1310[nm].(2) Sensor section manufactured circularly according to gas insulated switchgear. And $9/125[{\mu}m]$ standard single mode optical fiber for communication was installed winding 20 [turn] on sensor section core surroundings of diameter 31 [cm].(3) Electrical signal of PD(Photo detector) is collected using NI company's 16bit DAQ board via terminal block. Collected data analyzed by different three signal processing methods. NI company's $Labview^{TM}$ was used to signal processing software. As a result, In signal processing of optic current sensor, we could know that noise greatly more influences the error generation than fluctuation of light intensity. also, 1 class CT(current transformer) manufacture that have error rate less than 1[%] was available by removing these

• Electrical & Electronic Materials
• /
• v.7 no.6
• /
• pp.520-526
• /
• 1994

A rectifying heterojunction consisting of polyparaphenylene(PPP) and polypyrrole(PPY) films was prepared by the electrochemical method. The photoresponse in the heterojunction of PPY and PPP is similar to the absorption spectrum of undoped PPP. This fact suggests that photoresponse depends strongly upon polyparaphenylene of semiconductor. The fill-factor was calculated from the photo current-voltage curve to be 0.19, which is relatively small compared to polyacetylene-polythiophene heterojunctions.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.129-130
• /
• 2000

The emission color stability of poly(fluorene) derivatives upon thermal annealing or passage of current in an electroluminescent device is affected by the structure of the main chain polymer unit and particularly by the polymer chain end substituents. Proper attention to these features leads to colorfast blue emission in both photo- and electoluminescence. Furthermore, the spectral emission characteristics can be tuned by the incorporation of various comonomers. Preliminary single layer device studies validate the potential utility of poly(fluorene) homo and copolymers for OLED applications.

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.02a
• /
• pp.160-161
• /
• 2001

APD(avalanche photo diode)는 수광된 빛에 의해 생성된 캐리어를 강한 역바이어스 전압(40 ～ 400V)으로 가속시켜 avalanche 증배를 일으켜 큰 current를 얻을 수 있도록 제작된 소자이다. APD는 P-N 포토 다이오드에 비하여 수십～수백배의 높은 반응도(responsivity)를 얻을 수 있으며 응답 시간이 매우 짧다는 장점이 있는 반면 불규칙한 전류에 의해 만들어지는 내부 잡음 레벨이 높으며 온도에 민감하다는 단점을 갖고 있다. (중략)

• Journal of Biomedical Engineering Research
• /
• v.13 no.3
• /
• pp.201-208
• /
• 1992

In the indirect optical bio-telemetry, high frequency response and low minimum detectable optical power can be achieved by using photodiode with small light receiving area which minimizes junction capacitance. But, on the other hand, S/N ratio becomes low because the optical signal current is small. To solve such a problem, we attach plato-convex lens in front of photo diode, The results of comput- er simulation and experiments suggest promotion of light receiving efficiency and possibility of multi- telemetry system through directivity of convex lens in one room.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1453-1456
• /
• 2009

Transparent sol-gel hybrid dielectric material (hybrimer) coating films were fabricated by spin coating and photo or thermal curing of sol-gel derived oligosiloxane resins. Hybrimer coating films are suitable as the passivation layer of TFT in AMLCD due to low dielectric constant, small loss tangent, low leakage current density, high transmittance and thermal stability.

• Ceramist
• /
• v.23 no.2
• /
• pp.178-183
• /
• 2020

Solar energy conversion is now actively researching because of pollution. Especially silicon photocatalyst has big potential, because of wide absorption range. But low quantum yield of silicon photocatalyst can't be used for commercialization. This paper summarize mechanism of silicon photocatalyst. In addition, properties and current states of photo catalyst using nanomaterials of silicon are also introduced.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.411-415
• /
• 1987

A $32{\times}33$ MOS-type area image sensor has been fabricated. The blooming current is reduced to 1/14 by forming +p photocell in P-well instead of a simple p-type substrate. A shallow n+ junction is made to improve the sensitivity of photodiode on short wavelength. Bootstrapping circuit technique is applied to obtain high speed dynamic shift register. The shift register operates at up to 10MHz for 7V clock.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1153-1155
• /
• 1993

This paper presents some experimental result of current limiting, fusing and short circuit interruption behavior by notch construction of thin copper film $35{\mu}m$ on epoxy substrate. A fuse-link having elements of copper film provided high-precision small holes by photo eatching process.