• Journal of the Korean Ceramic Society
• /
• v.47 no.2
• /
• pp.146-150
• /
• 2010

Because the plasma display panel has used red, green and blue(RGB) phosphors, it has suffer from two intrinsic problems; 1) the cell defect due to the lack of binding force between phosphor particles and 2) mis-discharge because of difference of electrical characteristics among RGB phosphors. In order to control the mechanical and electrical properties of RGB phosphors, frit with $ZnOB_2O_3-SiO_2-Al_2O_3$ system was added to RGB phosphor as sintering additive. The mechanical properties were increased by the amount of frit. The amount of frit under 5 wt% rarely affected dielectric constant. However, there was the limit of amount because of decreasing optical properties seriously; over 3 wt% in red, over 10 wt% in green and blue.

• Journal of the Korean Chemical Society
• /
• v.47 no.6
• /
• pp.619-624
• /
• 2003

The $Gd_{1.9-x}Li_{0.1}Eu_xO_3$ (x=0.02, 0.05, 0.08, and 0.12) powders (${\thickapprox}1{\mu}m$) synthesized by sol-gel method, whose surfaces are modified in a colloidal silica suspension (size of $SiO_2$ particles: ${\sim}30$ nm), have been fabricated to highly stable and effective luminescent films on the glass substrates. Thanks to the fused $SiO_2$ nano particles in the vicinity of the glass softening temperature (at around $700^{\circ}C$), $Gd_{1.9-x}Li_{0.1}Eu_xO_3$ powders are strongly attached onto the surface of glass substrate (>9H, pencil hardness tester). This simple and low-cost method to get $Gd_{1.9-x}Li_{0.1}Eu_xO_3$ phosphor films without any loss of luminescence brightness would promise for applications to display devices.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1145-1148
• /
• 2008

The present status and trend of oxide phosphor thin-film development for thin-film electroluminescent (TFEL) device application are presented in this paper. Recently, several newly developed types of bendable or bendable see-through oxide TFEL lamps have been fabricated using the TFEL technology with a newly developed bendable ceramic sheet, glass sheet or sapphire sheet substrate, which has become available on the market. Stable operation at high temperatures was obtained in double-insulating-layer-type TFEL lamps fabricated with a $Zn_2Si_{0.6}Ge_{0.}4O_4$:Mn thin-film emitting layer forming on translucent or transparent bendable sheet substrates.

• Resources Recycling
• /
• v.29 no.3
• /
• pp.61-74
• /
• 2020

This study was conducted to improve the recycling process of waste fluorescent lamp, and investigate the possibility of using the waste fluorescent lamp glass as a raw material for glass beads, the leaching method of rare earth from the waste phosphor powder, and the possibility of solvent extraction of rare earth from the rare earth leaching solution. The waste phosphor contained 28.9% yttrium oxide, 3.46% cerium oxide, 1.95% europium oxide, 1.76% terbium oxide, and 1.43% lanthanum oxide. As a result of the trial production of glass beads using waste fluorescent lamp glass, it was judged that the production yield and quality were excellent, so that waste fluorescent lamp glass could be used as a raw material for glass beads. The soda roasted waste phosphor was leached in water and thereby the aqueous solution was blown with CO₂ to drop the pH to about 7, Then, Al, Si and residual N₂CO₃ were dissolved, and NaAlCO₃(OH)₂ and SiO₂ were precipitated in the aqueous solution. In the solvent extraction of cyanex272-hydrochloric acid, cyanex272-sulfuric acid, D2EHPA-hydrochloric acid, D2EHPA-sulfuric acid, Ionquest290-hydrochloric acid, Ionquest290-sulfuric acid, p507-hydrochloric acid using xylene as a diluent, the extraction yield of Y, Eu, Ce, La, and Tb are close to 100%. However, in this conditions, the difference in extraction yield for each element, that is, selectivity is 16% or less.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.145-146
• /
• 2000

Primary emphasis was placed on the electrophoretic deposition of low voltage phosphor to indium-tin oxide-coated glass for the application of field emission display. The phosphor deposited by various parameters, such as deposition time and applied voltages was examined in detail. In addition, a comparison was made by analyzing luminance properties of the phosphor mixed with and without conducting $In_2O_3$ powder of less than 1um size. The measurement was performed as a function of $In_2O_3$ concentration from 3% to 15% by weight. The enhanced impact of indium powder mixing on the phosphor was clearly demonstrated by aging performance curve at 1000V excitation voltages with a current density of $1\;mA/cm^2$

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.657-659
• /
• 2004

Trivalent cerium ($Ce^{3+}$) activated yttrium aluminum garnet ($Y_3Al_5O_{12}$, YAG) phosphor thin films were deposited on quartz glass substrates by rf magnetron sputtering. The effects of sputtering parameters and annealing condition on the luminescent properties were investigated. The sputtering parameters were $O_2$/Ar gas ratio, rf power, and deposition time. The films were annealed at 1200 $^{\circ}C$ for 5 hours in $N_2+$vacuum atmosphere. Polycrystalline YAG:Ce thin film phosphor could be obtained with a gas ratio of $O_2$/(Ar+$O_2$)=0.5 after post-annealing. PL spectra excited at 450 nm showed a yellow single band at 550 nm.

• International journal of advanced smart convergence
• /
• v.11 no.2
• /
• pp.59-63
• /
• 2022

In this study, we study of luminescent solar concentrators comprise thick glass with broadband antireflection coating deposited on the top surfaces and inorganic phosphor layers contacted on the bottom surfaces. Solar cells are contacted to the lateral surfaces of the glass. Experimental results show the broadband antireflection coating increased the short-circuit current of the solar cell.

• Korean Journal of Materials Research
• /
• v.31 no.1
• /
• pp.54-59
• /
• 2021

In this work, narrow-band green-emitting CsPbBr3 particles are embedded in commercialized glass composites by a facile dry process. By optimizing the method through sintering in glass frit (GF) composites including CsBr and PbBr2, used as precursors, the encapsulation of CsPbBr3 particles made them waterproof with green fluorescence. To improve the fluorescent properties by reducing aggregation of CsPbBr3, fumed silica (FS) is additionally used to help particles avoid bulking up in the glass matrix. The CsPbBr3 perovskite/glass composites are characterized using scanning electron microscopy (SEM) images and energy-dispersive X-ray spectroscopy (EDS) maps, which support the existence of CsPbBr3 particles in the glass matrix. The photoluminescence (PL) properties demonstrate that the emission spectrum peak, full width at half maximum (FWHM), and photoluminescence quantum yield (PLQY) values are 519 nm, 17 nm, and 17.7 %. We also confirm the water-resistant properties. To enhance water/moisture stability, the composite sample is put directly into water, with its PLQY monitored periodically under UV light.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.5
• /
• pp.541-544
• /
• 2004

Multi- wall carbon nanotubes(MWNTs) were synthesized by thermal chemical vapor deposition. The paste for screen printing was composed of MWNTs, organic vehicle and glass frit. Carton nanotube paste was screen-printed on ITO(indium tin oxide) deposited soda lim을 glass, and then heat treatment was performed. Before the surface treatment, turn on field of derive was 2.6 V/$\mu\textrm{m}$. After the surface treatment, the value was changed into 1.8 V/$\mu\textrm{m}$. The anode current of the derive with 2.83 V/$\mu\textrm{m}$(turn on field) was changed 4 $\mu\textrm{A}$ into 390 $\mu\textrm{A}$ at 1,700 V. Adsorption effect of MWNTs onto phosphor of anode plate was observed by the field emission measurement and resulted in bad effects on properties of devices lifetime and emission lighting.

• Journal of Korean Vacuum Science & Technology
• /
• v.3 no.1
• /
• pp.90-94
• /
• 1999

Field Emission display (FEDs) require enhancement in both driving methods and process techniques to improve the display image quality. However, from the point of view of manufacturing, it is difficult to find methods and techniques to realize low cost manufacturing. New and simple color phosphor screen designs were suggested with non-crossed electrode lines and full color anode panels for small area displays were demonstrated. To avoid unwanted reaction with gases produced from phosphors in a high vacuum glass container, a very thin polyimide layer was coated on the phosphor screen. Moreover, to improve the display image quality, black matrix composed of inorganic materials was fabricated. This paper describes the performance and characteristics of the new full color anode panels.