• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.270-272
• /
• 2018

This paper proposes an open-phase fault control system using 3-phase neutral voltage. The proposed control system is designed as a new topology which uses the potential difference between neutral point and ground(G) of three phase. And the open-phase detection system is configured to three resistance devices(Y-wiring) of the same capacity to each line of three phase power source R,S,T. This paper also designs a mobile phone application for remote alarm of open-phase fault.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.6
• /
• pp.939-945
• /
• 2009

This paper is described BLDC motor in the submarine propulsion system which is asked high power per unit area. This study analyzes the independent 6-phase BLDC motor a specific extended by existing the independent 3-phase BLDC motor and propose forward development direction. Independent 6-phase motor has a characteristics that phases of stator are independent electrically with each other and two's independence 3-phase BLDC motor are linked with each difference of 60 degree. Six-phase BLDC motor is simulated with Matlab-simulink, the simulation result has a high current and low torque pulsation than existent independence 3-phase BLDC motor.

• Journal of Welding and Joining
• /
• v.16 no.1
• /
• pp.114-124
• /
• 1998

The effect of matrix phase (austenite, pearlite, martensite) on the low stress abrasion resistance in the chromium-carbide-type high Cr white iorn hardfacing weld deposites has been investigated. In order to examine matrix phase, a series of alloys with different matrix phase by changing the ratio of Cr/C system by heat treatment were employed. The alloys were deposited twice on a mild steel plate using self-shielding flux cored arc welding process. The low stress abrasion resistance of the alloys against sands was measured by the Dry Sand/Rubber Wheel Abrasion Test(RWAT). Even though formation of pearlite phase in the matrix showed higher hardness than that of austenite, there was no observable difference in wear resistance between the pearlite and austenite phase for the same amount of chromium-carbide in the matrix. On the other hand, the formation of martensitic phase,, from heat treated austenitic alloys (high content of Cr), enhanced wear resistance due to its fine secondary precipitates.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.540-542
• /
• 2019

This paper proposes an open-phase fault control system using 3-phase neutral voltage. The proposed control system is designed as a new topology which uses the potential difference between neutral point and ground of three phase. The open-phase detection system is also configured to Y-wiring of three capacitance devices of the same capacity to each line of three phase power source R-S-T. This paper also designs a mobile phone application for remote alarm of open-phase fault.

• Proceedings of the KIPE Conference
• /
• 2018.11a
• /
• pp.4-6
• /
• 2018

This paper proposes an open-phase fault control system using 3-phase neutral voltage. The proposed control system is designed as a new topology which uses the potential difference between neutral point and ground(G) of three phase. And the open-phase detection system is configured to Y-wiring of three capacitance devices of the same capacity to each line of three phase power source R-S-T. This paper also designs a mobile phone application for remote alarm of open-phase fault.

• Current Optics and Photonics
• /
• v.5 no.3
• /
• pp.289-297
• /
• 2021

We describe a comb-mode resolving spectroscopic technique by direct time-domain phase correction of unstable interferograms obtained from loosely locked two femtosecond lasers. A low-cost continuous wave laser and conventional repetition rate stabilization method were exploited for locking carrier and envelope phase of interferograms, respectively. We intentionally set the servo control at low bandwidth, resulting in severe interferograms' fluctuation to demonstrate the capability of the proposed correction method. The envelope phase of each interferogram was estimated by a quadratic fit of carrier peaks to correct timing fluctuation of interferograms in the time domain. After envelope phase correction on individual interferograms, we successfully demonstrated 1 Hz linewidth of RF comb-mode over 200 GHz optical spectral-bandwidth with 10-times signal-to-noise ratio (SNR) enhancement compared to the spectrum without correction. Besides, the group delay difference between two femtosecond pulses is successfully estimated through a linear slope of phase information.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.28 no.1
• /
• pp.59-67
• /
• 2023

This paper explores the variation of DC-Link current ripple analysis in terms of duty cycle and phase angle of Multi-phase/Multi-stage boost converter. A 2-Stage/1-Stage boost converter DC-Link current is used to determine the difference between the 1st stage diode current and the 2nd stage inductor current. Each stage boost converter diode and inductor current is subordinate to the phase angle and duty cycle. The magnitude of the ripple current is variable according to phase angle and duty cycle. The analysis results are verified by variation of DC-Link current ripple using a 1kW typical 2-stage/1-stage boost converter.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.2
• /
• pp.45-53
• /
• 2013

In this paper, we analyze the typical phase voltage and line current waveform characteristics of the distribution system with 3 phase small synchronous generation source in case with load and non-load group, in order to investigate the power quality for end load connected of generation source. As demonstrated by our experimental results, the distortion and power quality of phase voltage and line current waveform were relatively good for low voltage 3 phase model grids connected of 3 phase small synchronous generation source in case with non-load group. However, distortion and power quality of voltage and current waveform was poor for low voltage 3 phase model grids connected to 3 phase small synchronous generation source in the load group with some phase voltage and frequency difference. From the above results, we conclude that the phase voltage and frequency of 3 phase generation source must be identical to that of distribution system source to maximize the power quality. Also, special attention is required in case of having load group or non-load group to 3 phase generation source.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.1
• /
• pp.39-44
• /
• 2013

In this paper digital phase-shifter for multi-arm spiral antennas was designed by using Hilbert transform. All frequency components in input signal are phase-shifted for 90 degree by Hilbert transform, and the transform is implemented by FIT and IFIT. Digital phase-shifter generates two signals with phase difference of 90 degree by using Hilbert transform from input signals sampled by analog-digital converter(ADC), and then the input signal is phase-shifted for a given phase by using two signals. Hilbert transform based on digital phase-shifter is designed by Xilinx System generator, and the effects of input noise, FIT point, sampling period, initial phase of input signal, and shifted phase are simulated and its results are compared with Matlab results.

• Asian-Australasian Journal of Animal Sciences
• /
• v.24 no.6
• /
• pp.791-799
• /
• 2011

This study examined the effect of restricting feed intake and the subsequent compensatory growth in Guzera females. Eighteen animals with an initial age of 21 months and a mean weight of 268.17 kg were placed in three groups according to the alimentary regime: feed ad libitum; feed restricted to 20% dry matter; and feed restricted to 40% dry matter. In the restricted feed phase, the dry mater intake decreased as the restriction levels increased, influencing the reduction in intake of other nutrients. In the realimentation phase, the 40% restricted feed group ingested more dry matter (% BW) and crude protein ($weight^{0.75}$) than the group fed ad libitum (p<0.001). The serum nutrient concentrations were inversely proportional (p<0.001) to the restriction level, and there was no difference (p>0.001) in the realimentation phase. In the restricted feed phase, the final live weight decreased (p<0.05) as the restriction level increased. For the daily mean weight gain in the control group, there was no difference (p>0.05) compared to the animals with 20% feed restriction, but this was higher than in the group with 40% feed restriction. In the re-alimentation phase, the group with 40% feed restriction achieved higher weight gain rates, which was different from the control and 20% restriction groups. In both phases, the animals in the group with 40% feed restriction presented better feed conversion which was different (p<0.05) from the control group. In the feed restriction phase, it was observed that the intake of N, nitrogen excreted in feces and urine, nitrogen balance and nitrogen retention decreased (p<0.05) with the restriction level. None of the variables were influenced in the re-alimentation phase. These results show that feed restriction by 40% can be adopted as a nutritional management practice.