• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.4
• /
• pp.38-45
• /
• 1997

A new dynamic model for the cutting process inb the end milling process is developed. This model, which describes the dynamic response of the end mill, the chip load geometry including tool runout, the dependence of the cutting forces on the chip load, is used to predict the dynamic cutting force during the end milling process. In order to predict accurately cutting forces and tool vibration, the model which uses instantaneous specific cutting force, inclueds both regenerative effect and penetration effect, The model is verified through comparisons of model predicted cutting force with measured cutting force obtained from machining experiments.

• Journal of the Korea Concrete Institute
• /
• v.15 no.3
• /
• pp.400-408
• /
• 2003

Chloride ion inside concrete destroys the so-called passive film surrounding reinforcing bars inside concrete so that the so-called salt attack accelerates corrosion which is the most critical factor for durability as well as structural safety of reinforced concrete structures. Recently, as a solution of the salt attack, the ground granulated blast-furnace slag(GGBFS) have been used as binder or blended cement more extensively. In this paper, characteristics of chloride ion diffusion for the GGBFS concrete, which is known to possess better resistance to damage due to the chloride ion penetration than ordinary portland cement(OPC) concrete possesses, are analyzed and a chloride ion diffusion model for the GGBFS concrete is proposed by modifying an existing diffusion model for the OPC concrete. The proposed model is verified by comparing diffusion analysis results using the model accelerated chloride penetration test results for concrete specimens as well as field test results for an RC bridge pier. Then, an optimal resistance condition to chloride penetration for the GGBFS concrete is obtained according to degrees of fineness and replacement ratios of the GGBFS concrete. The result shows that the GGBFS concrete has better resistance to chloride ion penetration than OPC concrete has and the resistance is more affected by the replacement ratio than the degree of fineness of the GGBFS.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.4
• /
• pp.451-458
• /
• 2004

The study was focused on the development of computational scheme in three dimensional configurations by applying effective heat capacity model to the numerical procedure in order to predict the temperature profiles of a buried pipeline and the frozen penetration depth(FPD) of a freezing soil medium. To realize this, the investigator conducted the unsteady state heat transfer analysis, using the commercial code ABAQUS, for the freezing granite soil medium including a pipeline in a closed system. The proposed model took into consideration the phase change effect of in situ pore water in the frozen fringe. The comparison of results obtained by the proposed model and the actual performances was valuable in establishing a level of confidence in the application of introduced theory.

• Journal of ILASS-Korea
• /
• v.23 no.1
• /
• pp.30-35
• /
• 2018

The objective of this study is to predict numerically the effect of intake humidification on the injected diesel fuel spray characteristics in a compression ignition engine. In this work, Wave model and Ducowicz model were applied as the break-up model and evaporation model, respectively. The amount of water vapor for the humidification was changed from 0% to 30% of injected fuel mass. The number of applied meshes was generated from 49,000 to 110,000. At the same time, the results of this work were compared in terms of spray tip penetration, SMD and equivalence ratio distributions. It was found that the cylinder temperature and cylinder pressure were decreased with increasing water vapor mass by vaporization latent heat and specific heat, however, the difference was very small. So, the spray tip penetration was not different by water vapor mass. Also, higher equivalence ratio distributions were observed with increasing water vapor mass by the improvement of fuel atomization.

• Journal of Soil and Groundwater Environment
• /
• v.8 no.1
• /
• pp.81-86
• /
• 2003

Understanding the penetration behavior of the spilled oil is very important to remove itself and to minimize its impact on intertidal biological communities by earlier treatment of the oil. The purpose of this study is to clarify the effects of wave and tidal actions on the penetration of spilled oil and to evaluate main factors of oil penetration using a sandy-beach model. Infiltration processes into the sediments showed significant difference between seawater and crude oil. Seawater was infiltrated by both wave action and tidal fluctuation into the sediments in sandy beach. However, spilled crude oil penetrated into the sediments only by falling tides and not by wave action, and the first tide is most important for the penetration of stranded oil. Over 70% of bulk fraction in penetrated crude oil was concentrated to the top 2 cm sediment-layer when spilled oil volume was 1 L/$\textrm{m}^2$. Moreover, the penetration of stranded oil into the sandy beach sediments was strongly correlated with the oil viscosity affected by temperature.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.4
• /
• pp.419-424
• /
• 2012

This paper presents a tubular reciprocating translational motion permanent magnet synchronous motor for percussive drilling applications for offshore oil & gas industry. The motor model and rock model are built up by doing force analysis of the motor and analyzing the physical procesof impact. The optimization of input voltage waveforms to maximize the rate of penetration is done by simulations. The simulation results show that the motor can be utilized in percussive drilling applications and achieve a very large impact force. Simulation results for optimization also show that second harmonic input voltage produces a higher rate of penetration than the sine wave and fourth harmonic input voltages.

• Journal of the Korean Society of Safety
• /
• v.23 no.4
• /
• pp.59-66
• /
• 2008

Recently, the deterioration of reinforced concrete structures, primarily due to corrosion of steel reinforcement, has become a major concern. Chloride-induced deterioration is the most important deterioration phenomenon in reinforced concrete structures in harsh environments. For the realistic prediction of chloride penetration into concrete, a mathematical model was developed in which the effects of diffusion, chloride binding and convection due to water movement can be taken into account. The aim of this research was to reach a better understanding on the physical mechanisms underlying the deterioration process of reinforced concrete associated with chloride-induced corrosion and to propose a reliable method for estimating these effects. Chloride concentrations coming from de-icing salts are significantly influenced by the exposure conditions such as salt usage, ambient temperature and repeated wet-dry cycles.

• Structural Engineering and Mechanics
• /
• v.13 no.6
• /
• pp.639-652
• /
• 2002

The present study aims to improve an existing model for the prediction of deceleration time history, penetration depth and forces on ogive and conical nose shaped missiles under normal impact into geo-material targets. The actual ogive nose shaped missile has been considered in the analysis and the results thus obtained have been compared with the existing model and significant improvements are found. A close proximity in the results has also been observed with the experimental values. The results of ogive nose shaped missile have also been compared with equivalent conical nose shaped missile. Variation of radial stresses along nose length and radial direction has been studied. Effect of CRH on missile penetrating performance has been investigated.

• Journal of the Korean institute of surface engineering
• /
• v.51 no.2
• /
• pp.133-137
• /
• 2018

Plasma devices such as jets, pencils, and torches have been developed as new tools that help penetration of target agents and applied to plasma medicine. However, these devices cannot be used in a large area. Therefore, we introduced a flexible plasma device, which can be treated of large area and designed as bendable plasma. In additional, in vitro model based on agarose gel was prepared that can be show effectiveness in the depth of penetration. Plasma treatment conditions such as power, time and distance can be optimized on the agarose gel wound model. The chemical structure of changed polysaccharides was predicted due to reactive excited atoms and molecules, UV photons, charged particles and reactive oxygen and nitrogen species (RONS).

• Journal of the Korea Institute of Military Science and Technology
• /
• v.3 no.2
• /
• pp.35-41
• /
• 2000

A modified theoretical analysis of the ballistic perforation on the double and multi-layered armour plates using an upper bound method has been presented in this paper. A modified model based on the suggestion of the Awerbuch-bodner model has been adapted and extended into double and multi-layered armour plates when the plugging type of penetration has been occurred. The residual projectile speed, ballistic limit velocity and contact time during the penetration process have been derived from the equation of motion at each stage.