• Journal of the Korean Geotechnical Society
• /
• v.31 no.11
• /
• pp.41-48
• /
• 2015

An investigation of a void and a loose layer of the ground is essential in order to prevent the losses of life and properties caused by subsidence and sinkage of the ground. Recently, studies on the ground penetrating radar survey have been actively conducted in order to estimate the void and the loose layer of the ground. However, an error can be committed by contrarily predicting a dense ground and a loose layer because the ground penetrating radar estimates an interface depth between geo-materials that have different electrical impedances. In this study, a loose ground depth is estimated using the characteristics of the reflected electromagnetic wave obtained from the ground penetrating radar survey. To gather the signals according to the loose ground depths, the ground penetrating radar survey is conducted on a field which underwent a huge ground settlement. In addition, the dynamic cone penetration test is performed to verify the result of the loose ground depth estimation from the ground penetrating radar survey. From the analysis of the reflection characteristics of the electromagnetic wave, a phase of an electromagnetic wave reflected from a denser soil layer is found to be identical with that of the first measured signal. On the other hand, a phase of an electromagnetic wave reflected from the loose soil layer is found to be opposed to that of the first detected signal. The comparison between the dynamic cone penetration index and electromagnetic signals by the ground penetrating radar shows that the estimated depth of the loose or dense layer is perfectly matched with a high reliability. The ground penetrating radar survey and the signal analysis performed in this study can be used not only for the survey of interface depth between the discontinuity layers but also for the estimation of the loose layer.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.6 no.1
• /
• pp.77-83
• /
• 2000

En coastal area, many submarine facilities such as pipes and cables are installed on/under the sea bed. Also, there are heavy traffic due to numerous vessels which call in ports or navigate passages in adjacent water. Therefore, the frequency of dropping anchors will be increased to avoid various dangerous situations. When an anchor is dropped from vessel on the sea bed, the anchor strikes on the sea bed, and then, the anchor penetrates to certain depth into the sea bed. In this case, sometimes submarine facilities on/under the sea bed may be damaged by the strike or the maximum penetrating depth of anchor. In this paper, some approximate equations on the strike and the penetrating depth of anchors have been derived on the basis of actual data, and the results are expected to use as basic design data of related facilities.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.3 s.131
• /
• pp.64-71
• /
• 2005

In this study, we attempted to apply ultrasonic treatment for the preservative treatment of two softwood species, Korean pine and Japanese red pines to evaluate its effectiveness. Wood samples were submerged in oilborne preservative, copper naphthenate (NCU) and waterborne preservative, alkyl ammonium compound (AAC) and then treated with ultrasonic wave of 40 kHz, 400 W. After the treatment, the retention and penetration depth of these preservatives in the specimens were measured as a function of treatment time. Both the retention and penetration depth were continuously increased with increasing the treatment time up to 120 hours, where the retention reached about 95% by the application of AAC and the penetrating depth of 95% and 83% by the application of NCU, respectively for both species. The results of electronic microscopic observation showed that the improved retention capacity could be attributed to air deflation, wood extractive deflation working of ultrasonic wavelength, and destruction of wood pits which served as the pathway of preservatives. The results suggested that the use of ultrasonic treatment could be applied to thick wood veneers for the production of laminated wood products.

• KCI Concrete Journal
• /
• v.12 no.1
• /
• pp.139-144
• /
• 2000

Ground Penetrating Radar (GPR) with 1 GHz antenna has been used to locate a steel bar embedded inside laboratory-prepared mortar specimens. Four mortar specimens are made with the dimensions of 100 cm (length) x 100 cm (width) x 14 cm (depth). One specimen had no bars and the other three specimens had a Dl9 steel bar at 4, 6. and 8 cm depth. As a part of the experimental work, the dielectric constants of mortar specimens are measured during curing. As the curing time increased. the dielectric constant decreased with decreasing moisture content inside the specimen. The steel bar embedded inside mortar specimens has been successfully identified in all three cases. The results using signal processing scheme developed in this study significantly improved the output of a commercially available radar system.

• Geophysics and Geophysical Exploration
• /
• v.8 no.2
• /
• pp.119-128
• /
• 2005

The assessment of erosional and depositional patterns near bridge piers is essential to understand the fluvial scour process. Geophysical surveys are particularly effective in determining the riverbed variations in a river and may also be of value for obtaining the previous scour history below the riverbed profile. In this study, GPR (Ground Penetrating Radar), as a non-destructive geophysical technique, was used to assess the existence and depth of existing and infilled scour thickness, streambed materials, and pre- and post- scour surfaces at the bridge piers in Han River, June 2002 and October 2002. The GPR acquisition system used for obtaining profiles of the shallow subsurface deposits was a portable GSSI SIR 2000 system with 100 and 400 MHz antennas. The GPR data obtained along the 24 bridge piers in the flow direction of the river and in the surroundings of 5 bridge piers were compared and presented in this study. It is concluded that GPR surveys can be effective in determining both the water depth and sub-bottom geological structure near the bridge piers and abutments provided that the appropriate instrumentation and operational procedures are applied.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.4 no.2
• /
• pp.167-174
• /
• 2000

Ground penetrating radar(GPR) was applied for measuring depths, sizes and intervals of rebars embedded in concrete. A concrete wall was constructed for this study and a sand pool and a concrete block were used for simulation. Result of this study shows that GPR can be used for measuring rebar depths and intervals, even though it is limitary, but that measuring sizes is almost impossible. Simulation with the sand pool was helpful for research on the versatile rebar arrays though signal was not clear as real concrete wall. A concrete block with many cylindrical holes for inserting different sized rebars could not be used for simulator due to many unknown reflective waves. Antenna orientation must be perpendicular to rebars for large reflection signal.

• Journal of Korea Water Resources Association
• /
• v.36 no.6
• /
• pp.893-899
• /
• 2003

In this study, a realtime bridge scour monitoring system was installed and operated to measure the real scour depths in relatively hard and rocky bottom. And riverbed change at before and after flood was investigated by GPR(Ground Penetrating Radar) to check the rationality of measured values. As the result of this study, it was revealed the inaccuracy of equilibrium scour depth estimation through the bridge scout equations because most of the equations do not reflect the differences of geological characteristics, evaluated the real scour depths considering both bed and flow conditions.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.16-23
• /
• 2018

In this study, Polydimethylsiloxane (PDMS) was applied to Strain Hardening Cement Composites (SHCC) for penetrating water repellency. The penetration depth of PDMS, strength of SHCC, and chloride ion penetration resistance of SHCC were investigated. As a result of measuring penetration depth of PDMS when applying different application method, it was confirmed that all methods satisfied the requirements of KS F 4930. Although the immersion method showed the largest penetration depth, the spray method was considered to be more appropriate considering the ease of field application. Compressive strength tests showed that the penetration depth of PDMS decreased as the compressive strength of SHCC increased. The compressive strength of M4-A and M4-B specimens with large PDMS penetration depths decreased by 9.6% and 8.0%, respectively, compared with those of M4 specimens produced without PDMS. Compressive strengths of the M1-A and M1-B specimens with small PDMS penetration depths were reduced by 4% and 2.2%, respectively, compared with the M1 specimen. As a result, it can be seen that the strength reduction rate of SHCC increases as the penetration depth of PDMS increases. The chlorine ion penetration tests showed that the chlorine ion penetration resistance increases with the penetration depth of PDMS.

• Journal of the Korea Concrete Institute
• /
• v.16 no.4 s.82
• /
• pp.477-484
• /
• 2004

As a part of durability improvement of concrete-structure, penetrating water repellency of liquid type is applied to concrete surface. Besides, a related standard is made recently, but the standard has been prescribe for initial settlement state of penetrating water repellency of liquid type, to the exclusion of performance variation depending time and outdoor environment factor. For measurement of performance variation, we measured the weight of outdoor exposure specimen every regular intervals and check a measured value against a measured value of different condition specimen. Moreover, after the application of penetrating water repellent, measured a adhesive strength in tension between cement-polymer modified waterproof coatings and surface of specimen. The applied penetrating water repellent is a emulsified silicon type with a deep penetration depth. In view of the results so far achieved, the more a Quantity of application and active solid content does get, the deeper penetrating water repellency of emulsion type Penetrate get longer and supplied moisture increase in quantity, a penetrating water repellency of liquid type penetrates more deep, but a quantity of water absorption increase gradually. Perhaps this result is caused by a reduction of active solid content on concrete surface, because active ingredient is moved into the concrete by dissolution.

• Geophysics and Geophysical Exploration
• /
• v.5 no.3
• /
• pp.185-192
• /
• 2002

We made a study of 3-D migration which could precisely image data of GPR (Ground Penetrating Radar) applied to NDT (Non-Destructive Test) field for the inspection of structural safety. In this study, we obtained 3-D migrated images of important targets in structuresurvey (e.g. steel pipes, cracks) by using 3-D Kirchhoff prestack depth migration scheme developed for seismic data processing. For a concrete model consisting of steel pipe and void, the targets have been well defined with opposite amplitude according to the parameters of the targets. And migrated images using Parallel-Broadside array (XX configuration) have shown higher resolution than those using Perpendicular-Broadside array (YY configuration) when steel pipes had different sizes. Therefore, it is required to analyze the migrated image of XX configuration as well as that of general YY configuration in order to get more accurate information. As the last stage, we chose a model including two steel pipes which cross each other. The upper pipe has been resolved clearly but the lower has been imaged bigger than the model size due to the high conductivity of the upper steel.