• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.730-736
• /
• 2016

In a previous study, the impact factor response spectrum and corresponding method for evaluating the load carrying capacity of bridges was suggested to improve the existing evaluation method. To verify the applicability of the suggested method, which is based on the frequency of bridges, the dynamic characteristic test for an actual single span simply-supported bridge was conducted. Through a field test under ambient traffic conditions, the dynamic response of the bridge was obtained using wireless accelometers and its fundamental frequency was identified. The peak impact factor was determined from the identified frequency and the impact factor response spectrum. The load carrying performance variation of the bridge was estimated considering the performance reduction factor, which was calculated using the current and previous natural frequency and impact factor. From the result, the load carrying capacity of the bridge was decreased, but the capacity was still enough because its value is greater than the design live load. Through the overall procedures and technical details presented in this paper, the suggested evaluation method can be applied to actual bridges with the acceleration data measured under ambient traffic conditions and the impact factor response spectrum.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.518-523
• /
• 2017

This paper proposes a novel denoising method based on non-local(NL) means. The NL-means algorithm is effective for removing an additive Gaussian noise, but the denoising parameter should be controlled depending on the noise level for proper noise elimination. Therefore, the proposed method optimizes the denoising parameter according to the noise levels. The proposed method consists of two processes: off-line and on-line. In the off-line process, the relations between the noise level and the denoising parameter of the NL-means filter are analyzed. For a given noise level, the various denoising parameters are applied to the NL-means algorithm, and then the qualities of resulting images are quantified using a structural similarity index(SSIM). The parameter with the highest SSIM is chosen as the optimal denoising parameter for the given noise level. In the on-line process, we estimate the noise level for a given noisy image and select the optimal denoising parameter according to the estimated noise level. Finally, NL-means filtering is performed using the selected denoising parameter. As shown in the experimental results, the proposed method accurately estimated the noise level and effectively eliminated noise for various noise levels. The accuracy of noise estimation is 90.0% and the highest Peak Signal-to-noise ratio(PSNR), SSIM value.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.111-116
• /
• 2018

This research examines the drop impact of an external cooling unit package of an air conditioner system. The packaging is composed of a shock-absorbing material, which protects the package contents by absorbing the impact energy and other parts for fixture. Accurate quantification of the impact acceleration experienced by the package contents is necessary to design an effective packaging with minimal volume and sufficient shock absorbing capacity. Explicit time integration was used for the drop impact analyses. A finite element model of the package was constructed, material testing and material model selection were carried out, and sensors for data acquisition were modeled to obtain accurate simulation results. The results were compared with real physical test data. Due to imprecise modeling of the damping, the acceleration and strain values predicted by the simulation were larger than those from physical test. However, the trend of the history data and the peak deceleration value in the direction of impact showed good agreements. Thus, the analysis model and scheme are suitable for the design of an air conditioner cooling unit package.

• Archives of Pharmacal Research
• /
• v.20 no.1
• /
• pp.1-6
• /
• 1997

We determined the microviscosity of synaptosomal plasma membrane vesicles (SPMV) isolated from bovine cerebral cortex and liposomes of total lipids (SPMTL) and phospholipids (SPMPL) extracted from SPMV. Changes in the microviscosity induced by the range and rate of lateral diffusion were measured by the intramolecular excimerization of 1, 3-di(1-pyrenyl)propane (Py-3-Py). The microviscosity values of the direct probe environment in SPMV, SPMTL and SPMPL were 38.17, 31.11 and 27.64 cP, respectively, at$37^{\circ}C$and the activation energies $(E_a)$ of the excimer formation of Py-3-Py in SPMV, SPMTL and SPMPL were 8.236, 7.448 amd 7.025 kcal/mol, respectively. Probe location was measured by polarity and polarizability parameters of the probe Py-3-Py and probe analogues, pyrene, 1-pyrenenonanol and 1-pyrenemethyl-3${\beta}$-hydroxy-22, 23-bisnor-5-cholenate (PMC), incorporated into membranes or solubilized in reference solvents. There existed a good linear relationship between the first absorption peak of the $^1_a$ band and the polarizability parameter $(n^{2}-1)/(2n^{2}+1)$.The calculated refractive index values for SPMV, SPMTL and SPMPL were close to 1.50, which is higher than that of liquid paraffin (n=l.475). The probe location was also determined by using a polarity parameter $(f-1/2f^{I})$. Here f=$({\varepsilon}-1)/(2{\varepsilon}+1)$ is the dielectric constant function and $f^I=(n^2-1)/(2n^2+1)$ is the refractive index function. A correlation existed between the monomer fluorescence intensity ratio and the solvent polarity parameter. The probes incorporated in SPMV, SPMTL, and SPMPL report a polarity value close to that of 1-hexanol $({\varepsilon}=13.29)$. In conclusion, Py-3-Py is located completely inside the membrane, not in the very hydrophobic core, but displaced toward the polar head groups of phospholipid molecules, e.g., central methylene region of aliphatic chains of phospholipid molecules.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.40 no.4
• /
• pp.359-364
• /
• 2014

In this study, we developed a HPLC method for the separation and analysis of methylparaben and p-anisic acid, which are commonly used as a synthetic preservative and natural preservative, respectively. Methylparaben and p-anisic acid have same molecular weight (152.15 g/mol), similar structure and same maximum absorption wavelength (250 nm), thus they showed same retention time (RT) value (13.3 min) in HPLC experiment. We observed that two substances are separated on C18 column after methylparaben was derivatized selectively through the acetylation reaction. Instead, RT of the acetylated methylparaben was moved to 23.9 min from 13.3 min. The average retention time was $23.9{\pm}0.1min$ and peak area values was $5042882{\pm}4778$. In addition it showed a high linearity in the calibration curve with a correlation coefficient (R2) of 0.9999658. Detection and quantitation limits were $1.47{\mu}g/mL$ and $4.44{\mu}g/mL$, respectively. In conclusion, the developed method can be useful for separation and analysis of preservatives with similar structure in cosmetic fields.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.3
• /
• pp.137-148
• /
• 2006

The purpose of this study was to compare muscle activity in the lower extremity during walking wearing jogging and roller shoes. Twelve male middle school students (age: 15.0 yrs, height 173.7 cm, weight 587.7 N) who have no known musculoskeletal disorders were recruited as the subjects. Seven pairs of surface electrodes (QEMG8, Laxtha Korea, gain = 1,000, input impedance >$1012{\Omega}$, CMMR >100 dB) were attached to the right-hand side of the body to monitor the rectus femoris (RF), vastus medialis (VM), vastus lateralis (VL), biceps femoris (BF), tibialis anterior (TA), and medial (GM) and lateral gastrocnemius (GL) while subjects walked wearing roller and jogging shoes in random order at a speed of 1.1 m/s. An event sync unit with a bright LED light was used to synchronize the video and EMG recordings. EMG data were filtered using a 10 Hz to 350 Hz Butterworth band-passdigital filter and further normalized to the respective maximum voluntary isometric contraction EMG levels. For each trial being analyzed, five critical instants and four phases were identified from the recording. Averaged IEMG and peak IEMG were determined for each trial. For each dependent variable, paired t-test was performed to test if significant difference existed between shoe conditions (p<.05). The VM, TA, BF, and GM activities during the initial double limb stance and the initial single limb stance reduced significantly when going from jogging shoe to roller shoe condition. The decrease in EMG levels in those muscles indicated that the subjects locked the ankle and knee joints in an awkward fashion to compensate for the imbalance. Muscle activity in the GM for the roller shoe condition was significantly greater than the corresponding value for the jogging shoe condition during the terminal double limb stance and the terminal single limb stance. Because the subjects tried to keep their upper body weight in front of the hip to prevent falling backward, the GM activity for the roller shoe condition increased. It seems that there are differences in muscle activity between roller shoe and jogging shoe conditions. The differences in EMG pattern may be caused primarily by the altered position of ankle, knee, and center of mass throughout the walking cycle. Future studies should examine joint kinematics during walking with roller shoes.

• Korean Journal of Materials Research
• /
• v.18 no.7
• /
• pp.347-351
• /
• 2008

We have fabricated and evaluated newNew high high-efficiency green green-light light-emitting phosphorescent devices with an emission layer of [$TCTA/TCTA_{1/3}TAZ_{2/3}/TAZ$] : $Ir(ppy)_3$ were fabricated and evaluated, and compared the electroluminescence characteristics of these devices were compared with the conventional phosphorescent devices with emission layers of ($TCTA_{1/3}TAZ_{2/3}$) : $Ir(ppy)_3$ and (TCTA/TAZ) : $Ir(ppy)_3$. The current density, luminance, and current efficiency of the a device with an emission layer of ($80{\AA}-TCTA/90^{\circ}{\AA}-TCTA_{1/3}TAZ_{2/3}/130{\AA}-TAZ$) : 10%-$Ir(ppy)_3$ were $95\;mA/cm^2$, $25000\;cd/m^2$, and 27 cd/A at an applied voltage of 10 V, respectively. The maximum current efficiency was 52 cd/A under the a luminance value of $400\;cd/m^2$. The peak wavelength and FWHM (FWHM (full width at half maximum) in the electroluminescence spectral were 513 nm and 65 nm, respectively. The color coordinate was (0.30, 0.62) on the CIE (Commission Internationale de I'Eclairage) chart. Under the a luminance of $15000\;cd/m^2$, the current efficiency of the a device with an emission layer of ($80{\AA}-TCTA/90{\AA}-TCTA_{1/3}TAZ_{2/3}/130{\AA}-TAZ$) : 10%-$Ir(ppy)_3$ was 34 cd/A, which has beenshowed an improvement of improved 1.7 and 1.4 times compared to those of the devices with emission layers of ($300{\AA}-TCTA_{1/3}TAZ_{2/3}$) : 10%-$Ir(ppy)_3$ and ($100{\AA}-TCTA/200{\AA}$-TAZ) : 10%-$Ir(ppy)_3$, respectively.

• Food Science and Preservation
• /
• v.13 no.3
• /
• pp.404-412
• /
• 2006

TThe purpose of this study was to investigate the physicochemical properties of chufa(Cyperus esculentus L., var sativus Boeck) starches by physical and chemical modification. Chufa starches were exposed to the microwave with 700W power oven for 1, 2, and 3 minutes. Also, starch was oxidized with 1.5%, 3% and 6% (15, 30, 60 mg Cl2/g starch $40^{\circ}\C$, pH 10, 3.0 hr) sodium hypochlorite. The shape of starch granules was not changed much by microwave heating and sodium hypochlorite. Water binding capacity increased but amylose content swelling power, and solubility decreased with increasing microwave heating time. Water binding capacity of the oxidized starch decreased with increasing the content of sodium hypochlorite. With increasing the microwave heating time, gelatinization temperature decreased, but enthalpy(${\Delta}H$) increased in physical modification of chufa starches. Also, chemically modified chufa starches have the similar pattern in gelatinization properties. Peak viscosities of RVA in physically modified chufa starches were 416-188 RVU, and in chemically modified chufa starches they were 129-267 RVU.

• Food Science and Preservation
• /
• v.18 no.2
• /
• pp.165-170
• /
• 2011

The physicochemical properties and cooking quality of Saechalssal bori (25% pearled ratio), which is a naked waxy barley, were investigated. The amylose, insoluble dietary fiber (IDF), soluble dietary fiber (SDF), total dietary fiber (TDF), and ${\beta}$-glucan contents of Saechalssal bori were 5.2, 10.8, 9.5, 20.3, and 3.7%, respectively. Pasting temperature, peak and final viscosity, and setback of Saechalssal bori were $66.5^{\circ}C$, 383.2, 231.3, and 55.6 RVU, respectively. The water absorption, expansibility, and soluble solid of Saechalssal bori were 232.2, 405.3, and 3.5%, respectively. As the ratio of water to grain increased, L value increased, whereas a and b values were decreased. The sensory evaluation showed that wateriness and overall acceptability increased with increasing ratio of water to grain, resulting in determining 2.1 times as the optimum ratio of water to grain. The cooked Saechalssal bori prepared using optimum condition had hardness (1.2 kg), cohesiveness (4.0), springiness (1.0), gumminess (5.1), chewiness (5.3), adhesiveness (0.2 kg), and A/H (0.8), respectively.

• Korean Journal of Environment and Ecology
• /
• v.33 no.6
• /
• pp.686-694
• /
• 2019

This study was carried out to identify the long-term changes to beech forest due to climate change in Ulleung-do. To study the traits of the stand structure of beech forest with micro-topography, we investigated the distribution of the basal area, important values, and indicated species in a small ridge between Albong basin and Seongin-bong peak, and 1-ha stands (20 m × 20 m, 25 sites) dominated beech species including on the upper slope and valley parts. The result showed that the indicator species characterizing the vegetation communities were Tsuga sieboldii, Rhododendron brachycarpum, and Mitchella undulata in the small ridge and Celtis jessoensis, Dryopteris crassirhizoma, and Ulmus laciniata in the valley part. Moreover, the individuals with the total DBH < 10 cm were more predominant in the small ridge and upper slope than in the valley part, the individuals with DBH = 10-25 cm were predominant in the small slope, and individuals with DBH = 25-45 cm and DBH > 45 cm were predominant in the upper slope. The reason for the predominant distribution of beech stand with DBH<10 cm in all terrains is suggested to be germination by nutritional propagation rather than secondary succession caused by artificial disturbances and seed propagation.