• 한국환경복원기술학회지
• /
• 제9권3호
• /
• pp.76-81
• /
• 2006

The reinforcement of soil shear strength by nylon net as substitute materials simulating a fine root system was evaluated by soil strength parameters(apparent cohesion(c) and internal friction angle(tan${\phi}$), using simple shear tester which clearly depicts shear deformation and controls soil suction. And the results of shear test by using bamboo as a substitute materials simulating a main root system and using nylon net as a substitute materials simulating a fine root system were compared. The reinforcement of soil strength by nylon net are expressed by apparent cohesion more than internal friction angle. In addition the increment of apparent cohesion by nylon net reached a peak in suction 60 $cmH_2O$. Different from with bamboo, the possibility of the change on internal friction angle(tan${\phi}$) caused by the soil water condition was shown in shear strain 20% condition. These results show that the mechanism of reinforcement by substitute materials simulating root system may be different in the condition of various soil water content.

• Geomechanics and Engineering
• /
• 제7권3호
• /
• pp.297-316
• /
• 2014

This paper presents a detailed study focused on investigating the effects of silt content on the static and dynamic properties of sand-silt mixtures. Specimens with a low-plastic silt content of 0, 15, 30 and 50% by weight were tested in static triaxial, cyclic triaxial, and resonant columns in addition to consolidation tests to determine such parameters as compression index, internal friction angle, cohesion, cyclic stress ratio, maximum shear modulus, normalized shear modulus and damping ratio. The test procedures were performed on specimens of three cases: constant void ratio index, e = 0.582; same peak deviator stress of 290 kPa; and constant relative density, $D_r$ = 30%. The test results obtained for both the constant-void-ratio-index and constant-relative-density specimens showed that as silt content increased, the internal friction angle, cyclic stress ratio and maximum shear modulus decreased, but cohesion increased. In testing of the same deviator stress specimens, both cohesion and internal friction angle were insignificantly altered with the increase in silt content. In addition, as silt content increased, the maximum shear modulus increased. The cyclic stress ratio first decreased as silt content increased to reach the threshold silt content and increased thereafter with further increases in silt content. Furthermore, the damping ratio was investigated based on different silt contents in three types of specimens.

• Geomechanics and Engineering
• /
• 제11권5호
• /
• pp.639-655
• /
• 2016

The effect of particle breakage and intermediate principal stress ratio on the behaviour of crushable granular assemblies under true triaxial stress conditions is studied using the discrete element method. Numerical results show that the increase of intermediate principal stress ratio $b(b=({\sigma}_2-{\sigma}_3)/({\sigma}_1-{\sigma}_3))$ results in the increase of dilatancy at low confining pressures but the decrease of dilatancy at high confining pressures, which stems from the distinct increasing compaction caused by breakage with b. The influence of b on the evolution of the peak apparent friction angle is also weakened by particle breakage. For low relative breakage, the relationship between the peak apparent friction angle and b is close to the Lade-Duncan failure model, whereas it conforms to the Matsuoka-Nakai failure model for high relative breakage. In addition, the increasing tendency of relative breakage, calculated based on a fractal particle size distribution with the fractal dimension being 2.5, declines with the increasing confining pressure and axial strain, which implies the existence of an ultimate graduation. Finally, the relationship between particle breakage and plastic work is found to conform to a unique hyperbolic correlation regardless of the test conditions.

• Geomechanics and Engineering
• /
• 제34권4호
• /
• pp.461-472
• /
• 2023

A box scale affects the shear behavior of soils in the direct shear test. The purpose of this study is to investigate the scale effect on the shear behavior of dilative granular materials by testing specimens of different heights placed in a type C shear box. Experimental tests were performed on specimens composed of glass beads with different heights and equal initial void ratios. Results showed that the peak friction and dilation angles linearly increased with the specimen height; however, the residual friction angle remained relatively constant. Similarly, the shear stiffness increased with the specimen height, rapidly reaching its peak state. Height does not have a significant effect on the total volume changes; nevertheless, a high aspect ratio can be assumed to result in global and homogeneous failure. The results and interpretations may be used as reference for recommending shear box scale in direct shear tests.

• 터널과지하공간
• /
• 제20권5호
• /
• pp.344-351
• /
• 2010

닫힌 균열을 따라 발생하는 전단거동을 Mode II 크랙의 시작과 진행으로 묘사할 수 있다. 파괴역학 이론에서는 순수 Mode II 재하에서 일반적으로 고유물성으로 인식되는 에너지 방출율(GII, Engergy Release Rate)이 한계점($G_{IIC}$)에 도달했을 때 전단거동이 시작된다고 예측한다. 지난 몇 년간 퍼듀대학의 암반공학그룹은 한계 에너지 방출률($G_{IIC}$)의 구속응력(normal stress)과 닫힌 균열의 거칠기에 대한 관계를 실험적으로 접근해왔다. 먼저 많은 실험들이 아크릴 재료를 대상으로 실행되었는데, 이는 광탄성(Photoelastic) 방법을 이용한 균열 끝(fracture tip)의 응력 집중 영역을 시각화하는 것을 가능케 해 주었다. 그 다음 실험 연구는 비교적 낮은 압축강도를 지닌 균질한 석고에 시행되었고, 최근에는 더 높은 압축강도를 지닌 재료를 대상으로 실험연구를 수행하였다. 그 예로 시멘트로 만든 시료 불록에 직접 전단 실험을 하였는데, 이전의 실험들과 마찬가지로 불연속면의 최대마찰각(Peak Friction Angle)이 잔류 마찰각(Residual Friction angle)과 비슷할 때만이 $G_{IIC}$가 재료의 고유물성으로 간주 될 수 있다는 점을 확인할 수 있었다. 그렇지 않은 경우에 한계 에너지 방출율($G_{IIC}$)은 구속응력과 함께 증가한다.

• 터널과지하공간
• /
• 제29권5호
• /
• pp.292-304
• /
• 2019

완만한 거칠기를 갖는 석회암 자연절리면에 대하여 KSRM 표준시험법에 의거한 개별적 직접전단시험과 수직응력을 단계별로 조절하는 다단계 직접전단시험을 실시하였다. 각 시험을 통해 전단시험 전후의 절리면 거칠기 변화를 알아보았고, 두 가지 시험에서 얻은 전단특성 값의 차이를 분석하였다. 두 가지 시험에서 모두 절리면의 거칠기가 클수록 전단저항은 증가하였으며, 수직응력이 증가할수록 절리면의 전단에 필요한 최대전단응력 값은 증가하였다. 다단계 직접전단시험으로 구한 최대마찰각은 개별적 직접 전단시험으로 구한 것의 63% 수준에 불과하였다. 다단계시험은 절리면 요철부의 초기 맞물림이 단계적인 전단과정에 따라 시험 중 수시로 변화되어 원래의 거칠기가 변형되기 때문에 암석 절리면의 마찰각을 구할 때는 개별적 직접전단시험이 더 유효한 방법으로 판단된다. JRC값 4~8의 완만한 거칠기를 갖는 석회암 절리면의 물성값은 최대마찰각 $47^{\circ}$, 잔류마찰각 $38^{\circ}$, 점착력 37 kPa으로 평가되었다.

• Tribology and Lubricants
• /
• 제30권2호
• /
• pp.71-76
• /
• 2014

As the importance of transmission efficiency to reducing fuel consumption and conserving the environment rapidly increases, reducing the drag torque in an automotive wet clutch is emerging as an important issue in the automotive industry. The drag torque in a clutch occurs from viscous drag generated by automatic transmission fluid in the narrow gap between separate friction plates. In this study, the drag torques in an automotive wet clutch are investigated with respect to the angle and density of the grooves between separate friction plates by three-dimensional finite element simulation of a single set of wet clutch disks considering the two-phase flow of air and oil. The simulation results shows that the drag torque generally increases with the rotational speed to a critical point and then decreases at the high-speed regime. The grooves between the plates plays an important role in reducing the drag peak, and the inclined angle of the grooves affects the oil flow. The grooves with an angle of $50^{\circ}$ shows the lowest drag torques at both low and high speeds. The flow vectors inside the $50^{\circ}$ grooves shows clear evidence that the fluid flows out more easily from the grooves compared with the flow vectors inside grooves with lower angles. The simulation results shows that increasing the number of grooves (density of grooves) decreases the drag torque.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2002년도 춘계 기술심포지움 논문집
• /
• pp.193-197
• /
• 2002

The tribological properties and van der Waals attractive forces and the thermal stability of films are very important characteristics of highly hydrophobic fluorocarbon (FC) films for the long-term reliability of nano system. The effect of thermal annealing on films and van der Waals attractive forces and friction coefficient of films have been investigate d in this study. It was coated Al wafer which was treated O2 and Ar that ocatfluorocyclobutane ($C_4_{8}$) and Ar were supplied to the CVD chamber in the ratio of 2:3 for deposition of FC Films. Static contact angle and dynamic contact angle were used to characterize FC films. Thickness of films was measured by variable angle spectroscopy ellipsometer (VASE). Nanotribological data was got by atomic force microscopy (AFM) to measure roughness, lateral force microscopy (LFM) to measure friction force, and force vs. distance (FD) curve to evaluate adhesion force. FC films were cured in N2 and vacuum. The film showed the slight changes in its properties after 3 hr annealing. FTIR ATR studies showed the decrease of C-F peak intensity in the spectra as the annealing time increased. A significant decrease of film thickness has been observed. The friction force of Al surface was at least thirty times higher than ones with FC films. The adhesive force of bare Al was greater than 100 nN. After deposit FC films adhesive force was decreased to 40 nN. The adhesive force of films was decreased down to 10 nN after 24 hr annealing. During 24 hr annealing in $N_2$and vacuum at $100^{\circ}C$ film properties were not changed so much.

• 한국지반환경공학회 논문집
• /
• 제18권2호
• /
• pp.29-37
• /
• 2017

집중호우로 인하여 산악지반에 발생하는 토석류의 거동은 대상지반 세립분의 전단강도 및 유변학적 특성들에 의하여 영향을 받기 때문에, 두 특성에 대한 정수는 토석류 거동을 파악하는데 매우 중요한 요소이다. 본 연구에서는 직접전단 실험을 통하여 세립분의 전단강도 및 유변학적 정수를 평가하고자 하였다. 건조상태와 액성한계상태로 조성된 두 가지 세립분 시료에 대하여 직접 전단실험을 수행하였으며, 연직응력에 따른 전단강도를 측정하여 점착력과 내부마찰각을 산정하였다. 또한 액성한계로 조성된 시료의 잔류전단강도를 획득하기 위하여 전단변형률속도와 전단방향을 변화시켜 반복전단실험을 수행하였다. 실험 결과, 액성한계상태의 시료는 건조 상태 시료에 비해 내부마찰각은 작지만 점착력은 더 큰 것으로 나타났으며, 잔류전단강도를 통해 산정한 내부마찰각과 점착력은 첨두전단강도에 의해 산정된 결과보다 작은 것으로 나타났다. 반복전단 결과, 전단변형률속도와 잔류전단강도는 선형적인 관계를 보였으며, 전단변형률속도-잔류전단강도 관계의 기울기로써 결정되는 점성은 약 $73.60Pa{\cdot}s$로 산정되었다. 본 연구는 직접전단 장비가 산악지반 토석류 거동과 관련된 세립분의 전단강도 및 유변학적 정수 산정에 효과적으로 활용될 수 있음을 보여준다.

• 한국지반공학회지:지반
• /
• 제13권5호
• /
• pp.5-18
• /
• 1997

공중투하법으로 만든 등방압밀 모래공시체를 평면변형률 압축시험을 실시하여 강도.변형특성의 이방성을 연구하였다. 세계 각국의 주요 연구기관에서 사용되고 있는 7종류의 연구용 표준시공시체를 최대주응력방향(e,)의 변형률과 최소주응력방향(e3)의 변형률을 각각 $10^{-60}에서\; 10^{-2}$ 까지 상세히 측정하였다. 그 결과,실험한 모든 모래에 대하여 변형률 0. 001%이하까지의 변형률에 있어서는 최대주응력이 퇴적면과 이루는 각도 5에 관계없이 탄성적.등방적인 거동을 나타내었다. 그러나, 변형률이 증가하여 탄성한계를 넘어면 점차퍽으로 이방적인 성질을 띄게 되고 마침내 피크에 도달하면 최대내부마찰각 $\phi_{max}은 \delta가\; 90^{\circ}에서 0^{\circ}$로 감소함에 따라 감소하고 그 최소치와 최대치의 비는 0.82-0.90 사이에 있었다. 또, $\phi_{max}$값의 최소치는 모래의 종류에 따라 $ \delta=0^{\circ}-30^{\circ}$ 사이에 있었다. 그러나, 잔류상태에 도달하면 모래는 다시 등방적인 거동을 하여 $\pji는\delta$에 크게 의존하지 않고 거의 일정한 값을 나타내었다.