• Journal of the Optical Society of Korea
• /
• v.8 no.3
• /
• pp.122-126
• /
• 2004

The method to obtain four speckle patterns with relative phase shift of ${\pi}/2$ by passive devices such as two waveplates and a linear polarizer, awl to calculate the phase at each point of the speckle pattern in shearography with a Wollaston prism is presented, and the feasibility of the proposed method is theoretically demonstrated by Jones vector.

• Proceedings of the Optical Society of Korea Conference
• /
• 2006.02a
• /
• pp.373-374
• /
• 2006

This paper physically demonstrates that our proposed method improves the Signal-to-Noise Ratio (SNR) of significantly increase the number of acceptable optical signals in PON(Passive Optical Network) systems. This method reduced Optical Beat Interference(OBI) by using CDMA.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.10
• /
• pp.1496-1511
• /
• 2002

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2018.11a
• /
• pp.535-536
• /
• 2018

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2004.10a
• /
• pp.476-483
• /
• 2004

This paper presents a hybrid system combining lead rubber bearings and hydraulic actuators controlled by a μ-synthesis method for seismic response control of a cable-stayed bridge. A hybrid system could alleviate some of restrictions and limitations that exist when each system is acting alone because multiple control devices are operating. Therefore, the overall control performance of a hybrid system may be improved compared to each system, however the overall system robustness may be negatively impacted by active device in the hybrid system or active controller may cause instability due to small margins. Therefore, a f-synthesis method that guarantees the robust performance is considered to enhance the possibility of real applications of the control system. The control performances of the proposed control system are compared with those of passive, active, semiactive control systems and hybrid system controlled by LQG algorithm and an extensive robust analysis with respect to stiffness and mass matrices perturbation and time delay of actuator is performed. Numerical simulation results show that the control performance of the proposed control system is superior to that of the passive system and slightly better than that of the active and semiactive systems and two hybrid systems show similar control performances. Furthermore, the hybrid system controlled by a μ-synthesis method shows the good robustness without loss of control performances. Therefore, the proposed control system could effectively be used to seismically excited cable-stayed bridge which contains many uncertainties.

• Computational Structural Engineering
• /
• v.11 no.1
• /
• pp.227-235
• /
• 1998

A method of calculating the natural frequency corresponding to the first mode of vibration of beams and tower structures, with irregular cross-sections and with arbitrary boundary conditions was developed and reported by D. H. Kim in 1974. This method has been developed for two-dimensional problems including the laminated composite plates and was proved to be very effective for the plates with arbitrary boundary conditions and irregular sections. In this paper, the result of application of this method to the building slabs with passive and active control devices is presented. Finite difference method is used to obtain the deflection influence surfaces needed for this vibration analysis in this paper. The influence of the modulus of the foundation on the natural frequency is thoroughly studied.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.4
• /
• pp.66-71
• /
• 2011

This study focused on the application of the Passive Solar Chamber System (PSCS) as proposed by a previous study. The seasonal performance and sizing method for the system were investigated for a feasibility of the PSCS in Korean climate. For seasonal performance, heat and ventilation performances of the PSCS were analyzed for the months of January and August. This study proposed a simple configuration method in which the designer can decide on the system size at the preliminary design stage by using system efficiency, overall heat transfer coefficient transmission, monthly solar radiation, highest and lowest temperatures. During weeks that require heating, the system showed to acquire a daily average heat amount of $860.28Wh/m^2$ day. For cooling periods, the system was computed to supply a daily average natural ventilation of $1,360.2m^3/day$ to the room. Moreover, proposed sizing method and the overall computation results showed a 6.04~7.24% error of assessment.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.6
• /
• pp.549-558
• /
• 2020

In this paper, the method is discussed such that the robustness of automatic initiated narrowband target tracking is improved in passive sonar. In the case of automatic tracking initiation as target in passive sonar, due to a number of clutter, the clutter is initiated as target and tracked which prohibits the operation capability. The associated probability and information entropy of measurements, extracted from detection data, is calculated to keep going on automatic target initiation and tracking of true target, but reduce the automatic initiation and tracking of clutter. If the association probability and information entropy of the extracted measurements is satisfied for the predefined conditions, the procedure of automatic initiation begins. Using sea-trial data, simulations are executed and the results from the proposed method indicate that it keeps the automatic target initiation and tracking of true target and suppresses the automatic target initiation and tracking of clutters in contrary to the conventional method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.11A
• /
• pp.1053-1058
• /
• 2006

In this paper, We proposed a efficient OSA(Optical Sub-Assembly) packaging method in use 1.31/1.49um bi-directional hybrid-integrated PLC chip for low-cost OSA in optical access network system applications as GE-PON in FTTH. Fabricated OSA with passive optical fiber alignment and nonhermetic plastic package method and measured optical coupling efficiency and electric-optical characteristics. Its performance is feasible to satisfy the GE-PON ONU specifications with the results as less than 0.5dB coupling losses within 40um alignment of z-axis and less than -24dBm sensitivity. It also has good temperature characteristics to sustain optical output power more than 1.5mW and 10dB extinction ratio, less than 0.3dB tracking error.

• Food Science and Preservation
• /
• v.20 no.3
• /
• pp.317-322
• /
• 2013

This study was conducted to investigate the effects of pretreatment and different packaging methods on the physicochemical properties of cold vacuum-dried peaches. All the dried peach samples were stored such as $N_2$ gas substitution, vacuum and passive packaged with polyethylene (PE) film and oriented polypropylene (OPP)/aluminum (Al)/PE film at $40^{\circ}C$ for 50 days. The weight change, pH, soluble solids content, titratable acidity, soluble solid-acid ratio (SS/TA), delta E, browning degree and phenolic compounds were analyzed. The weight change and pH were lower in the 0.1% vitamin C-treated group and were significantly lowest in the vacuum-treated OPP/AL/PE. The soluble solids content and the SS/TA were higher in the non-treated groups than in the vitamin C-treated groups. According to the packaging methods, the $L^*$ values were higher in the vacuum, $N_2$ gas and passive package, in that order. In addition, the browning degree and the delta E value were lower in the pretreated groups and significantly lowest in the vacuum-treated OPP/AL/PE with 0.1% vitamin C group. The phenolic compounds were high for the pretreated groups, according to the packaging methods (vacuum > $N_2$ gas> passive), and the OPP/AL/PE was significantly higher than the PE. These results suggest that different packaging materials and pretreatment methods affected the quality of the dried peaches, and the vacuum-OPP/AL/PE film packaging group showed a high quality.