• Progress in Medical Physics
• /
• v.15 no.4
• /
• pp.215-219
• /
• 2004

Due to their excellence for the high-energy therapy range of photon beams, researchers show increasing interest in applying MOSFET dosimeters to low- and medium-energy applications. In this energy range, however, MOSFET dosimeter is complicated by the fact that the interaction probability of photons shows significant dependence on the atomic number, Z, due to photoelectric effect. The objective of this study is to develop a very detailed 3-dimensional Monte Carlo simulation model of a MOSFET dosimeter for radiological characterizations and calibrations. The sensitive volume of the High-Sensitivity MOSFET dosimeter is very thin (1 ${\mu}{\textrm}{m}$) and the standard MCNP tallies do not accurately determine absorbed dose to the sensitive volume. Therefore, we need to score the energy deposition directly from electrons. The developed model was then used to study various radiological characteristics of the MOSFET dosimeter. the energy dependence was quantified for the energy range 15 keV to 6 MeV; finding maximum dependence of 6.6 at about 40 keV. A commercial computer code, Sabrina, was used to read the particle track information from an MCNP simulation and count the tracks of simulated electrons. The MOSFET dosimeter estimated the calibration factor by 1.16 when the dosimeter was at 15 cm depth in tissue phantom for 662 keV incident photons. Our results showed that the MOSFET dosimeter estimated by 1.11 for 1.25 MeV photons for the same condition.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.163-169
• /
• 2019

Sn-Pb solder alloys in electronics rapidly has been replaced to Pb free solder alloys because of various environmental regulations such as restriction of hazardous substances directive (RoHS), European Union waste electrical, waste electrical and electronic equipment (WEEE), registration evaluation authorization and of chemicals (REACH) etc. Because Sn58%Bi (in wt.%) solder alloy has low melting point and higher mechanical properties than that of Sn-Pb solder, it has been studied to manufacture electronic components. However, the reliability of Sn58%Bi solder could be lowered because of the brittleness of Bi element included in the solder alloy. Therefore, we observed the microstructures of Sn58%Bi composite solders with various contents of Sn-decorated multiwalled carbon nanotube (Sn-MWCNT) particles and evaluated bonding strength of the FR-4 components assembled with Sn58%Bi composite solder. Also, microstructures and bonding strengths of the Sn58%Bi composite solder joints were evaluated with the number of reflows from 1 to 7 times, respectively. Bonding strengths and fracture energies of the Sn58%Bi composite solder joints were measured by die shear test. Microstructures and fracture modes were observed with scanning electron microscope (SEM). Microstructures in the Sn58%Bi composite solder joints were finer than that of only Sn58%Bi solder joint. Bonding strength and fracture energy of Sn58%Bi composite solder including 0.1 wt.% of Sn-decorated MWCNT particles increased up to 20.4% and 15.4% at 5 times in reflow, respectively.

• Polymer(Korea)
• /
• v.33 no.4
• /
• pp.389-395
• /
• 2009

To develop the carrier of hydrophobic antifungal agents based on low molecular weight water-soluble chitosan (LMWSC), LMWSC was chemically modified with deoxycholic acid (DA) which is one of the bile acid as a hydrophobic group. The nanoparticles (WSCDA) using DA conjugated LMWSC were characterized using dynamic light scattering (DLS) and transmittance electron microscope (TEM). The particle size of WSCDA ranged from 250 to 350 nm and increased with the number of DA substitution. The loaded itraconazole as an antifungal agent WSCDA nanoparticles (WSCDA-ITCN) were prepared by solvent evaporation method. The drug content and the loading efficiency were investigated approximately $9{\sim}10%$ and $61{\sim}68%$ by UV spectrophotometer, respectively. The release of drug from nanoparticles was slow and showed sustained release characteristics. Based on the results of release study that the higher DA contents in WSCDA, the slower the releasing rate, the WSCDA-ITCN could be used as an excellent antifungal agent.

• Journal of Life Science
• /
• v.25 no.4
• /
• pp.481-485
• /
• 2015

Retroviruses genes have been inserted into the human genome for millions of years. These retroviruses are now inactive due to mutations such as deletions or nonsense mutations. After mutation, retroviruses eventually became fixed in the genome in their endogenous forms and existed as traces of ancient viruses. These retroviruses are called endogenous retroviruses (ERVs), with the human form known as human endogenous retrovirus. HERV cannot become a fully active virus, but a number of viral proteins or even virus particles are expressed under various conditions. Compared to endogenous retroviruses, some exogenous retroviruses are still infectious and can threaten human life. Among these, human immunodeficiency virus (HIV) is one of the most well-known and best-studied. Recent studies have shown some elements of HERV were activated by HIV infection and interact with HIV-derived proteins. In addition, many studies have attempted to use HERV as vaccination against HIV infection. This review will describe the regulation and interaction between HERV and HIV infection and mention the development of vaccines and therapeutic agents against HIV infection by using HERV elements.

• The Journal of Engineering Geology
• /
• v.18 no.2
• /
• pp.145-152
• /
• 2008

A fault gouge zone which is about 25cm thick crops out along a small valley in Yangbuk-myeon, Gyeongju city. It is divided into greenish brown gouge and bluish gray gouge by color. Under the microscope, the gouges have a lot of porphyroclasts composed of old gouge fragments, quartz, feldspar and iron minerals. Clay minerals are abundant in matrix, defining strikingly P foliation by preferred orientation. Microstructural differences between bluish pay gouge and greenish brown gouge are as follows: greenish brown gouge compared to bluish gray gouge is (1) rich in clay minerals, (2) small in size and number of porphyroclasts, and (3) plentiful in iron minerals which are mostly hematites, while chiefly pyrites in bluish gray gouge. Hematites are considered to be altered from pyrites in the early-formed greenish brown gouge under the influence of hydrothermal fluids accompanied during the formation of bluish gray gouge that also precipitated pyrites. It is believed that the fault core including bluish gray gouge zone and greenish brown gouge zone was formed by progressive cataclastic flow. In the first stage the fault core initiates from damage zone of early faulting. In the second stage damage zone actively transforms into breccia zone by repeated fracturing. The third stage includes greenish brown (old) gouge formation in the center of the fault core mainly by particle grinding. In the third stage further deformation leads to the formation of new (bluish gray) gouge zone while old gouge zone undergoes strain hardening. Consequently, the whole gouge zone in the core widens.

• Analytical Science and Technology
• /
• v.10 no.1
• /
• pp.66-74
• /
• 1997

Influence of the axial dispersion on immobilized enzyme catalytic bed was investigated in order to examine the kinetic behavior of the biocatalysis. The enzyme employed in this study was the tyrosinase(EC 1.14.18.1) immobilized on carbon support : this system requires two substrates of phenol and oxygen. This enzyme has potential application for phenol degradation in waste water. A simulated reactor was a packed-bed reactor of 2.54cm in diameter and 10cm long, loaded with the immobilized carbon particle with an average diameter of $550{\mu}m$. A phenol feed in the strength of 55.5mM(5220ppm) was used to observe the behavior of the immobilized enzyme column at three different dissolved oxygen levels of 0.08445mM(2.7ppm), 0.1689mM(5.4ppm) and 0.3378mM(9.5ppm) with the flow rates in the range of 60(1mL/s) to 180mL/min(3mL/s). Examination of the Biot number and Damkolher numbers of the immobilized system enables us to eliminate the contribution of external mass transfer to set of differential equations derived from the dispersion model. Solution of the equation was finally obtained numerically with the application of the Danckwert boundary conditions and the assumed zero-and first order rates on the non-linear two substrate enzyme kinetics. Higher conversion of phenol was observed at the low flow rates and at the higher oxygen concentration. Comparison of axial dispersion and plug flow model showed that no detectable difference was observed in the column outlet conversion between the axial and the plug flow models which was in complete agreement with the previous studies.

• Korean Journal of Soil Science and Fertilizer
• /
• v.38 no.5
• /
• pp.238-246
• /
• 2005

We conducted this investigation to observe competitive adsorption phenomena among the heavy metals onto the available sorption sites of soil particle surfaces in sandy clay loam and clay soil collected from Nonsan city, Chungnam and Yoosung, Daejeon in Korea, respectively. Polluted and contaminated soils can often contain more than one heavy metal species, resulting in competition for available sorption sites among heavy metals in soils due to complex competitive ion exchange and specific sorption mechanism. And the adsorption characteristics of the heavy metals were reported that the selectivity for the sorption sites was closely related with electropotential and electro negativity carried by the heavy metals. The heavy metals were treated as single, binary and ternary systems as bulk solution phase. Adsorption in multi-element system was different from single-element system as Cr, Pb and Cd. The adsorption isotherms showed the adsorption was increased with increasing equilibrium concentrations. For binary and ternary systems, the amount of adsorption at the same equilibrium concentration was influenced by the concentration of individual ionic species and valence carried by the respective heavy metal. Also we found that the adsorption isotherms of Cd and Pb selected in this experiment were closely related with electronegativity and ionic potential regardless number of heavy metals in solution, while the adsorption of Cr carried higher valance and lower electro negativity than Cd and Pb was higher than those of Cd and Pb, indicating that adsorption of Cr was influenced by ionic potential than by electronegativity. Therefore adsorption in multi-element system could be influenced by electronegativity and ionic potential and valance for the same valance metals and different valance, respectively. But it still needs further investigation with respect to ionic strength and activity in multi-element system to verify sorption characteristics and reaction processes of Cr, especially for ternary system in soils.

• Journal of Bio-Environment Control
• /
• v.12 no.1
• /
• pp.7-11
• /
• 2003

Cellular glass foam (CGF), the reprocessed glass, has a possibility to be used as a medium component in plug culture of horticultural crops due to the its excellent air and water permeability as comparable to perlite. An experiment was conducted to investigate growth of plug seedlings of Lycopersicum esculentum 'Segye' as influenced by irrigation frequency in various medium combinations of CGF (2.0-4.0 mm particle size) and peatmoss. Seeds were sown in 200-cell plug trays, filled with mixtures of CGF and peatmoss either at 33：67 or 25：75 (％. v/v) and were germinated on a fogged propagation bed. The irrigation frequencies used were one, two or three times per every two days. A commercial plug medium (Tosilee medium) was used as the control, and the irrigation frequency in the control was one time per day. Growth of seedlings, and medium pH and EC were measured at 33 days after sowing. The medium composition had little influence on overall growth of seedlings. Irrigation frequency very significant affected number of leaves, leaf area, chlorophyll concentration, fresh and dry weights of shoots and roots, and dry matter. Growth of seedlings was the greatest with the highest irrigation frequency in the 25% CGF＋75% peatmoss mixture.

• Applied Chemistry for Engineering
• /
• v.30 no.5
• /
• pp.597-605
• /
• 2019

In order to improve the adhesion of water-based adhesive, gemini type nonionic reactive surfactants were synthesized and applied to water-based adhesives. The surfactants were synthesized by using maleic acid and polyoxyethylene cetyl ether having different length of ethylene oxide and confirmed by FT-IR and $^1H-NMR$. Their appearance was light yellow wax. The cloud point of the compound was more than $78^{\circ}C$. The measured critical micelle concentration (c.m.c) was $1.0{\times}10^{-4}{\sim}7.0{\times}10^{-4}mol/L$ and surface tension at c.m.c was 25.9~32.0 mN/m. As the number of ethylene oxide increased, the emulsifying power was improved. The foaming height of each compound by Ross-Miles method was 1.4~4.5 cm. The synthesized surfactants was then used as an emulsifier in emulsion polymerization of water-based adhesives and its physical properties were evaluated. The solid contents of prepared adhesives was 59%. The average particle size and initial tackiness of the prepared adhesives were 164~297 nm and ball no. of 20~32, respectively. The peel strength was $1.8{\sim}2.1kg_f/mm$. The retention rate of adhesives viscosity was evaluated to 99% during 30 days. Therefore, synthesized gemini type nonionic reactive surfactants are expected to be applied as an emulsifier for the high adhesive force.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.169-169
• /
• 2015

유사 입자의 크기는 유사의 특성 및 그에 따른 거동 변화에 중요한 영향을 미친다. Stokes 침강 속도 모형에서 유사의 침강 속도에 가장 많은 영향을 주는 인자는 유사의 크기인 것 또한 확인된다. 유사 입자의 크기가 약 $60{\mu}m$보다 작은 유사들은 알갱이 사이의 점착력을 무시할 수 없다. 이로 인해 유사들은 응집 현상을 겪으며 입자 본래의 크기보다 크기가 큰 플럭을 형성하는 점착성 유사로 분류된다. 응집 현상이란, 흐름 내 점착성을 띠는 일차입자(Primary Particle)가 응집과 파괴를 반복하며 플럭을 형성하는 현상을 뜻한다. 입자 간의 충돌을 통해 응집이 진행되며 난류 전단으로 인해 형성된 플럭의 파괴가 발생한다. 많은 연구에서 점착성 유사의 충돌을 야기하는 가장 지배적인 원리는 난류라 알려져 있다. 이러한 응집 현상으로 인하여 플럭의 크기와 밀도는 지속적으로 변화를 겪으며 비점착성 유사와 다른 특징들을 보인다. 흐름에 존재하는 유사의 이동은 이송-확산 방정식을 통해 표현된다. 이송-확산 방정식은 시간 변화에 따른 농도의 변화를 입자의 침강과 난류 및 유사 자체의 특징에 의한 확산으로 해석한다. 침강속도로 대변되는 이송과 달리, 확산은 난류흐름 내에서 유사가 확산되는 정도를 정량화하기 위한 인자가 요구된다. 난류에 의한 유사의 확산은 유사 자체 특성에 따른 물질 확산에 비하여 매우 큰 값을 가지며, 이를 확산 계수로 개념화 한다. 확산계수는 와점성계수와 Schmidt 수(${\sigma}_c$)의 비로 정의된다. ${\sigma}_c$는 난류의 점성과 난류로 인한 부유과정에 의해 유사가 확산되는 정도를 나타낸다. 이에 따라 ${\sigma}_c$의 변화가 유사의 부유 및 침강거동에 많은 영향을 미칠 것이라 판단되나, 국내외에서 수행된 연구 동향에서는 ${\sigma}_c$를 0.5부터 1.0 사이의 상수를 적용하여 수행되었다. 이에 본 연구에서는 ${\sigma}_c$의 크기에 따라 달라지는 유사의 부유 및 침강 변화에 의한 총 부유량을 살펴보고자 한다. 유사의 점착성을 고려할 수 있는 1DV 수치 모형을 이용하여 비점착성 유사와 점착성 유사를 대상으로 수치연구를 수행하며, 유사의 크기 및 ${\sigma}_c$의 변화에 따른 총 부유량 경향을 살펴본다. 그 결과, 점착성 유사는 ${\sigma}_c$의 증가에 따라서 유사의 총 부유량이 증가하는 현상이 나타난 반면 비점착성 유사는 ${\sigma}_c$의 증가에 따라 유사의 총 부유량이 감소하는 경향이 나타났다. 그러나 크기가 아주 작은 비점착성 유사를 대상으로 수치 연구를 수행한 결과, ??에 따른 총 부유량의 경향은 유사의 점착성에서 기인하는 것이 아닌 입자의 크기로부터 야기되는 특성이라는 결론이 도출되었다.