• Journal of Powder Materials
• /
• v.1 no.1
• /
• pp.42-51
• /
• 1994

6061Al-SiCP metal matrix composite materials(MMCs) were fabricated by injecting SiCP particles directly into the atomized spray. The main attraction of this technique is the rapid fabrication of semi-finished, composite products in a combined atomization, particulate injection(10 $\mu\textrm{m}$, 40 $\mu\textrm{m}$, SiCP) and deposition operation. Conclusions obtained are as follows; The microstructure of the unreinforced spray formed 6061Al alloy consisted of relatively fine(50 $\mu\textrm{m}$) equiaxed grains. By comparision, the microstructure of the I/M materials was segregated and consisted of relatively coarse(150 $\mu\textrm{m}$) grains. The probability of clustering of SiCP particles in co-sprayed metal matrix composites increased it ceramic particle size(SiCP) was reduced and the volume fraction was held constant. Analysis of overspray powders collected from the spray atomization and deposition experiments indicated that morphology of powders were nearly spherical and degree of powders sphercity was deviated due to composite with SiCp particles. Interfacial bonding between matrix and ceramics was improved by heat treatment and addition of alloying elements(Mg). Maximum hardness values [Hv: 165 kg/mm2 for Al-10 $\mu\textrm{m}$ SiCp Hv--159 kg/mm2 for Al-40 $\mu\textrm{m}$SiCp] were obtained through the solution heat treatment at $530^{\circ}C$ for 2 hrs and aging at $178^{\circ}C$, and there by the resistance were improved.

• Journal of Pharmaceutical Investigation
• /
• v.38 no.1
• /
• pp.39-43
• /
• 2008

Cyclosporin A (CyA), a potent immunosuppressive drug used in allogeneic transplants and autoimmune disease, is a typical water-insoluble drug. Recently, nanoparticle carriers were investigated to improve the intestinal absorption of drugs. In this study, CyA-loaded nanostructured lipid carriers (NLCs) were prepared from a hot o/w emulsion using the high pressure homogenization method. The NLCs were consisted of cationic lipids, solid lipids, liquid lipids (oils), surfactant and stabilizer. Encapsulation efficiency of CyA in NLCs was approximately 71%. The average particle size and zeta potential of NLCs were below 250 nm and above +40 mV, respectively. The morphology of NLCs was confirmed by transmission electron microscopy (TEM) analysis. Compared to the CyA powder, higher in vitro release of CyA from NLCs was observed after burst release within 30 min. Thus, CyA-loaded NLCs could be applied not only for parenteral route but also for gastrointestinal administration, which needs further investigation.

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.2
• /
• pp.183-187
• /
• 2010

Core-Shell polymers of silicone dioxide-styrene system were prepared by sequential emulsion polymerization. In inorganic/organic Core-Shell composite particle polymerization, silicone dioxide adsorbed by surfactant sodium dioctyl sulfosuccinate (EU-DO133L) was prepared initially and then core silicone dioxide was encapsulated emulsion by sequential emulsion polymerization using styrene at the addition of potassium persulfate (KPS) as an initiator. We found that $SiO_2$ core shell of $SiO_2$/styrene structure was formed when polymerization of styrene was conducted on the surface of $SiO_2$ particles, and the concentration sodium dioctyl sulfosuccinate (EU-DO133L) was 0.5~2.0g. The structure of core-shell polymer were investigated by measuring to the thermal decomposition of polymer composite using thermogravimetric analyzer and morphology of latex by scanning electron microscope(SEM).

• Analytical Science and Technology
• /
• v.27 no.6
• /
• pp.314-320
• /
• 2014

$La_{2-x}(MoO_4)_3:Er^{3+}/Yb^{3+}$ particles with doping concentrations of $Er^{3+}$ and $Yb^{3+}$ ($x=Er^{3+}+Yb^{3+}$, $Er^{3+}$=0.05, 0.1, 0.2 and $Yb^{3+}$ = 0.2, 0.45) were successfully prepared by the microwave-modified sol-gel method, and the upconversion photoluminescence properties were investigated. Well-crystallized particles, formed after heat-treatment at $900^{\circ}C$ for 16 h, showed a fine and homogeneous morphology with particle sizes of $2-5{\mu}m$. Under excitation at 980 nm, $La_{1.7}(MoO_4)_3:Er_{0.1}Yb_{0.2}$ and $La_{1.5}(MoO_4)_3:Er_{0.05}Yb_{0.45}$ particles exhibited a strong 525 nm emission band, a weak 550 nm emission band in the green region, and a very weak 655 nm emission band in the red region. The Raman spectra of the doped particles indicated the presence of strong peaks at higher frequencies of 752, 846, 922, 1358 and $1435cm^{-1}$ and lower frequency of $314cm^{-1}$ induced by the disorder of the $[MoO_4]^{2-}$ groups with the incorporation of the $Er^{3+}$ and $Yb^{3+}$ elements into the crystal lattice or by a new phase formation.

• Applied Chemistry for Engineering
• /
• v.20 no.5
• /
• pp.565-569
• /
• 2009

Nano-sized green and blue phosphor powders were synthesized by liquid phase method to confirm the size and morphology. By using that process, the particle sizes of green and blue phosphor particles were 80 nm and 60 nm, respectively. The characteristic comparison of $Zn_2SiO_4$ : Mn and BAM : Eu was carried out and as a result, $Zn_2SiO_4$ : Mn powders showed an higher PL performance compared to BAM : Eu.

• Journal of Powder Materials
• /
• v.24 no.2
• /
• pp.141-146
• /
• 2017

$Bi_2Te_3$ powders are recovered by wet chemical reduction for waste n-type thermoelectric chips, and the recovered particles with different morphologies are prepared using various surfactants such as cetyltrimethylammonium bromide (CTAB), sodium dodecylbenzenesulfonate (SDBS), and ethylenediaminetetraacetic acid (EDTA). When citric acid is added as the surfactant, the shape of the aggregated particles shows no distinctive features. On the other hand, rod-shaped particles are formed in the sample with CTAB, and sheet-like particles are synthesized with the addition of SDBS. Further, particles with a tripod shape are observed when EDTA is added as the surfactant. The growth mechanism of the particle shapes depending on the surfactant is investigated, with a focus on the nucleation and growth phenomena. These results help to elucidate the intrinsic formation mechanism of the rod, plate, and tripod structures of the $Bi_2Te_3$ recovered by the wet reduction process.

• Journal of the Korean Ceramic Society
• /
• v.46 no.2
• /
• pp.170-174
• /
• 2009

$BaTiO_3$ powder was synthesized by the solid-state reaction of fine $BaTiO_3$ and $TiO_2$ raw materials. Fine grinding media of 50 and 300 microns were used for obtaining fine particulate mixture of $BaTiO_3$ and $TiO_2$ with high homogeneity. Effect of the size of grinding media on the synthesis mechanism of $BaTiO_3$ was discussed on the basis of the particulate morphology and thermogravimetry data for the mixture powders. By using the finer grinding media, $BaTiO_3$ was formed at the lower temperature and the particle size with the relatively narrower distribution could be obtained. $BaTiO_3$ powder with the average size of 100 nm was synthesized by the solid reaction in vacuum atmosphere.

• Polymer(Korea)
• /
• v.36 no.5
• /
• pp.662-667
• /
• 2012

Poly(ethylene terephthalate) (PET) base films with high light transmittance have been used for the substrate of various functional films in the flat panel display. The effects of the reflective index of coated films, the roughness of the film surface and the content of inorganic silica particles on the light transmittance were studied in this article. Light transmittance was increased by coating a water soluble resin with a low reflective index at an optimum thickness. The roughness of the film did not affect light transmittance when the Ra of the film surface was less than a quarter of the wavelength of incident light. Inorganic silica particles decreased light transmittance due to their absorbance and scattering of the incident light.

• Korean Journal of Materials Research
• /
• v.26 no.7
• /
• pp.363-369
• /
• 2016

$NaCaLa_{1-x}(MoO_4)_3:Ho^{3+}/Yb^{3+}$ ternary molybdates with proper doping concentrations of $Ho^{3+}$ and $Yb^{3+}$ (x = $Ho^{3+}+Yb^{3+}$, $Ho^{3+}$ = 0.05 and $Yb^{3+}$ = 0.35, 0.40, 0.45 and 0.50) were successfully synthesized by microwave sol-gel method. Well-crystallized particles formed after heat-treatment at $900^{\circ}C$ for 16 h showed a fine and homogeneous morphology with particle sizes of $3-5{\mu}m$. Under excitation at 980 nm, the UC intensities of the doped samples exhibited strong yellow emissions based on the combination of strong emission bands at 520-nm and 630-nm emission bands in the green and red spectral regions, respectively. The optimal $Yb^{3+}:Ho{3+}$ ratios were obtained at 9:1 and 10:1, as indicated by the composition-dependent quenching effect of the $Ho^{3+}$ ions. The pump power dependence of the upconversion emission intensity and the Commission Internationale de L'Eclairage chromaticity coordinates of the phosphors were evaluated in detail.

• Korean Journal of Materials Research
• /
• v.27 no.1
• /
• pp.8-11
• /
• 2017

Binary Ti-Al alloys containing 50 to 60 atomic percent aluminum are rapidly solidified by hammer anvil method under an argon atmosphere. Constituent phases in each alloy are identified by X-ray diffractometry and microstructures of the alloys are investigated using a transmission electron microscope. In alloys with aluminum content between 50 and 54 percent, a second phase exists besides TiAl(${\gamma}$); this second phase is identified as $Ti_3Al$(${\alpha}2$). The ${\alpha}2$ phase is observed in two types of morphology. One is as fine lamellar alternating with ${\gamma}$ and the other is as a particle. It is concluded that the existence of a metastable phase with the morphologies stated above should arise from a higher quenching rate attained by the hammer anvil method as compared to the conventional roll or splat-quench method. Implications of the above observation are discussed with respect to the phase relations in the Ti-Al binary system; these implications are still controversial in many respects.