• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.2
• /
• pp.245-256
• /
• 2014

I-core sandwich panel that has been used more widely is assembled using high power $CO_2$ laser welding. Kim et al. (2013) proposed a circular cone type heat source model for the T-joint laser welding between face plate and core. It can cover the negative defocus which is commonly adopted in T-joint laser welding to provide deeper penetration. In part I, a volumetric heat source model is proposed and it is verified thorough a comparison of melting zone on the cross section with experiment results. The proposed model can be used for heat transfer analysis and thermal elasto-plastic analysis to predict welding deformation that occurs during laser welding. In terms of computational time, since the thermal elasto-plastic analysis using 3D solid elements is quite time consuming, shell element model with multi-layers have been employed instead. However, the conventional layered approach is not appropriate for the application of heat load at T-Joint. This paper, Part II, suggests a new method to arrange different number of layers for face plate and core in order to impose heat load only to the face plate.

• Archives of Craniofacial Surgery
• /
• v.15 no.1
• /
• pp.40-42
• /
• 2014

Ganglion cysts are most common on the dorsum of the hand or wrist, but they can occur in any part of the body. There have been few papers reporting ganglion cysts originating from the sternoclavicular joint, with most of these cases developing in children. A 76-year-old woman was referred to our department because of a painless mass over the right sternoclavicular joint. The mass was excised along with the portion of the sternoclavicular joint capsule surrounding the stalk. Histopathologic examination showed the cyst wall to be composed of compressed collagen fibers without evidence of an epithelial or synovial lining, which was consistent with ganglion cyst. To our knowledge, this is the first report of such a cyst in an adult. We consider this to be a useful report for surgeons that treat mass lesions occurring in almost any part of the body surface.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.3
• /
• pp.64-73
• /
• 2000

The joint parts was composed of inner AL(aluminum) ring, FRP wedge and motor case which was manufactured by filament wound method. Where the motor case consists of helical and hoop layer. The finite element analysis was performed for the design variable of joint parts to improve the performance of motor case. Where the adhesive layer was modeled to elasto-perfect plastic material and the contact condition of AL ring and wedge was modeled by using the contact surface element of ABAQUS. And the sliding distance of AL ring and the hoop strain of composite case were compared to hydro-static test results to verify the accuracy of analysis results. When wedge and AL ring was perfect bonding, though the hoop strain of joint part was reduced, the maximum shear stress was occurred at the adhesive layer. Thus the adhesive layer had failed due to the high shear stress before the failure was occurred at the case. And as another design method, when wedge and AL ring was contact condition, the shear stress on adhesive layer was decreased. But the hoop stress of joint part increased due to the sliding behavior of AL ring. Finally, the fail was occurred at the composite case of joint part. The improved joint method reinforced by hoop layer to the joint parts under contact condition for wedge and Al. ring reduced the joint part's hoop strain by constraint the sliding behavior of AL ring.

• Asia Marketing Journal
• /
• v.14 no.3
• /
• pp.49-68
• /
• 2012

When a channel is vertically separated, there can be inefficiencies, double marginalization. Channel coordination to amend this inefficiency has been an important issue in marketing and economics. Channel coordination deals with maximization of joint profit and achieving proper profit sharing among participants. In this paper, a manufacturer and heterogeneous multiple retailers with exclusive territory are assumed, and channel coordination with two-part tariff is considered. When multiple heterogeneous retailers are assumed, profit sharing can be an issue even though the tariffs based on marginal cost can maximize joint profit. In case of multiple heterogeneous retailers, the manufacturer earns the same profit (fixed fee) from each retailer. This means that a large retailer occupies all the gaps of channel profit between small and large markets. Then, the manufacturer, which generally plays the role of Stackelberg leader, will consider increasing fixed price or marginal price to earn more profit from large retailer. Those reactions can sacrifice maximization of joint profit by making small retailer withdraw or by changing the sales quantities. In this paper, to maximize joint profit and achieve proper profit sharing, two kinds of optional tariffs are considered. The first is an optional two-part tariff based on marginal cost and the second is an optional modified two-part tariff in which marginal prices are higher than the manufacturer's marginal cost. In both types of optional tariffs, maximization of joint profit in each market can be achieved. Moreover, optional tariffs alleviate the problem of profit sharing. Optional tariffs can provide a manufacturer more profit from a large retailer when profit from a small retailer is given. However, the analysis shows that the maximum share of manufacturer from a large retailer is restricted by the condition for self-selection. In case of optional two-part tariffs based on marginal cost, if the gap between demands is large, the maximum share of the manufacturer is sufficient to achieve proper profit sharing. If the gap between demands is not sufficiently large, the manufacturer cannot earn sufficient share from increased profit. An optional modified two-part tariff where marginal price is more than marginal cost of manufacturer is considered because of this scenario. The marginal price above the marginal cost may additionally control the distribution of the increased profit. However, the analysis shows that a manufacturer's maximum profit from a large retailer with given profit from a small retailer is the same as or lower than the maximum profit when optional two-part tariffs based on marginal cost are applied. Therefore, it can be concluded that the optional modified tariffs do not have additional contribution to profit sharing relative to the tariffs based on marginal cost. Although this paper does not cover all kinds of optional tariffs that are different from tariffs based on marginal cost, it shows the advantage of optional tariffs based on marginal cost and has important theoretical implications. The result of this paper also gives guide for channel coordination. Optional two-part tariff based on marginal cost can increase efficiency in channel coordination.

• Journal of Welding and Joining
• /
• v.17 no.6
• /
• pp.25-31
• /
• 1999

Stainless steel sheets are commonly used for vehicles such as the bus and the train. These are mainly fabricated by spot-welding. By the way, its fatigue strength is lower than base metal due to high stress concentration at the nugget. edge of the spot-welding. By the way, its fatigue strength is lower than base metal due to high stress concentration at the nugget edge of the spot-welding point. Especially, it is influenced by welding conditions as well as geometrical factors of spot welded joint. Therefore, it is not too much to say that structural rigidity and strength of spot-welded structures is decided by fatigue strength of spot welded lap joint. Thus, it is necessary to establish a reasonable and systematic long life design criterion for the spot-welded structure. In this study, numerical stress analysis was performed by using 3-dimensional finite element model on IB-type spot-welded lap joint of 304 stainless steel sheet under tension-shear load. Fatigue tests were also conducted on them having various thickness, joint angle, lapped length, and width of the plate. From the results, it was found that fatigue strength of IB-type spot-welded lap joints was influenced by its geometrical factors, however, could be systematically rearranged by maximum principal stress ({TEX}$σ_{1max}${/TEX}) at the nugget edge of the spot-welding point.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.6 no.1
• /
• pp.241-254
• /
• 2002

Though there are many kinds of type in the expansion joint of bridges, Transflex joint was usually used from 1970's to 1980's. But it made of rubber is needed to exchange to new one often because of the breakage by wheel load. This study performed the safety estimation which is to exchange the transflex joint to finger joint kept the part of situ-cast-concrete. The standard of finger joint is same as that of transflex joint, we investigated the safety of finger joint with experimental results and FEM (Finite element method) analysis.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.29B no.11
• /
• pp.31-35
• /
• 1992

This paper presents a decentralized adaptive controller design for a robot manipulator to track the given desired trajectory in the joint space. The controller is of distributed structure and does not require the complex manipulator dynamic model, thereby it is computationally very efficient. Each joint is independently controlled by a PID feedback part and a velocity-acceleration feedforward part. Simulation results for a two-link direct drive manipulator conform that the proposed decentralized scheme is feasible.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1993.10a
• /
• pp.74-78
• /
• 1993

Compared with rigid-jointed latticed dome, in pinned-joint latticed dome, results of Ref.1 showed reduction of buckling strength by decline of junction's rotational rigidity. Moreover, with decline of junction's rotational rigidity, geometrical initial imperfection incurs more and more reduction of buckling-strength. This study, subsequently the case of rigid-joint domes, is aimed at analyzing buckling-characteristics of pinned-joint single-layer latticed domes with triangular network subjected to initial imperfection.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.4
• /
• pp.188-193
• /
• 2005

The purpose of this paper is to develop a more precise damper model of the joint for the quantification of the joint mechanical properties. We modified the linear damper model of a knee joint model to nonlinear one. The normalized RMS errors between the simulated and measured joint angle trajectories during passive pendulum test became smaller with the nonlinear damper model than those of the linear one which indicates the nonlinear damper model is better in precision and accuracy. The error between the experimental and simulated knee joint moment also reduced with the nonlinear damper model. The reduction in both the trajectory error and the moment error was significant at the latter part of the pendulum test where the joint angular velocity was small. The nonlinearity of the damper was significantly greater at thin subject group and this indicates the nonlinearity is a useful index of joint mechanical properties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.217-217
• /
• 2009

In this study, the effect of bending strain on the transport property and critical current of lap and butt-jointed BSCCO tapes have been investigated. The samples were joined using a mechanically controlled jointing procedure. In order to ensure a uniform pressure application at the joint part, a single point contact has been devised and also to achieve a uniform thickness at the joint interface.