• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.794-799
• /
• 2005

In this paper, the inductive power collector using electromagnetic induction for the PRT(Personal Rapid Transit) system is suggested and some ideas for power collector design to improve the power transfer performance are presented. The proposed the inductive power collector is used for the PRT system, which has a large air-gap and demands a large electrical power capability. But, low output power is generated due to a loosely coupled characteristic of the large air-gap. Therefore, double layer construction of secondary winding. which was divided in half to increase both output current and output voltage was suggested. Also, model of power collector and parallel winding structure are presented, in addition, the performance of inductive power collector to alignment condition between the primary power line and the inductive power transformer was verified by computer simulation of 2kW model.

• Biomedical Science Letters
• /
• v.11 no.3
• /
• pp.301-305
• /
• 2005

MR spectroscopy of intracellularly located $^{133}Cs$ has been used to monitor the uptake of Gd-EOB-DTPA by the isolated rat liver. As shown by ${31}P$ spectroscopy, accumulation of $^{133}Cs$ ions in hepatocytes does not produce detectable effects on the metabolism. The hepatic internalization of Gd-EOB-DTPA was followed by the paramagnetic relaxation enhancement of the intracellular $^{133}Cs$ ions, and confirmed by parallel quantitations of Gd and Cs run by inductively coupled plasma analysis of liver samples and aliquots of perfusate. Two peaks are observed at -22.0 and -23.5 ppm, with respect to the line of the external reference arbitarily set to 0 ppm. Upon rinsing of the extracellular compartment with regular K-H free of CsCl, the high-field resonance disappears within 20min. The intracellular concentration was confirmed by ICP, which gives a $Cs^+$ content of $22.0\pm3.5mM$. The relaxation data significantly underestimate the Gd content, suggesting a potential compartmentation of $Cs^+$ and the contrast agent.

• Proceedings of the KAIS Fall Conference
• /
• 2006.05a
• /
• pp.381-383
• /
• 2006

본 논문에서는 5.8Ghz ISM대역 평행 결합선로 대역통과 여파기를 설계 제작하였다. 긴본적인 설계는 저역통과 여파기에서 대역통과 여파기로 변환한 후, 직 병렬 공진기를 이용한 설계와 J-인버터를 이용해 평행 결합선로 대역통과 여파기를 구현하였다. 2개의 공진 주파수를 실제로 구현하기 어렵기 때문에 하나의 공진기만을 사용하기 위해 인버터를 사용하였다. 또한 실제적인 마이크로스트립 라인의 layout크기를 결정하기 위해 우수 기수 모드 임피던스를 해석하고 근사식을 통해 스트립라인의 치수를 결정하였다. 이런 과정을 토대로 5.8GHz ISM밴드용 평행 결합선로 대역통과 여파기를 설계, 제작하였다.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.317-322
• /
• 2003

In this paper, we design a slow-wave bandpass filter that uses a microstrip line periodically loaded with microstrip ing resonators for WLAN(5 GHz). Unlike conventional slow-wave filters, this filter is designed to produce a narrow passband at the fundamental mode of the resonators and provide lower insertion loss than that of parallel- or cross-coupled ring bandpass filters. A PBG(Photonic Band Gap) structure patterned in the ground plane is used to suppress the spurious transmission and extend out-of-band rejections Experimental result shows that the first spurious response in the stopband of the slow-wave bandpass filter can be rejected using a PBG structure.

• Proceedings of the KIEE Conference
• /
• 2005.04a
• /
• pp.215-217
• /
• 2005

In this paper, the inductive power collector using electromagnetic induction for the PRT{Personal Rapid Transit) system is suggested and some ideas for power collector design to improve the power transfer performance are presented. The proposed the inductive power collector is used for the PRT system, which has a large air-gap and demands a large electrical power capability. But, low output power is generated due to a loosely coupled characteristic of the large air-gap. Therefore, double layer construction of secondary winding, which was divided in half to increase both output current and output voltage was suggested. Also, model of power collector and parallel winding structure are presented, in addition, the performance of inductive power collector to alignment condition between the primary power line and the inductive power transformer was verified by computer simulation of 2kW model.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.3
• /
• pp.25-32
• /
• 1992

In UHF, VHF new design method of samll-sized 3-dB 0$^{\circ}$/180$^{\circ}$ ring hybrid terminated arbitrary impedance using both lumped elements and distributed elements is presented. At the center frequency of 900 MHz, 3-dB 0$^{\circ}$/180$^{\circ}$ ring hybrid terminated arbitrary impedance is designed, analyzed and tested. Good agreements are obtained between measured and theoretical modeling results, and at the same time, the circuit area of hybrid fabricated with two dimensional parallel coupled line, distributed elements and lumped elements is reduced by more than 70% compared with only distribyted-type circuits.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.3
• /
• pp.565-573
• /
• 2000

In this paper, a interdigital microstrip bandpass filter is designed. A interdigital microstrip bandpass filter has many advantages such as insertion return loss, lower return loss, higher frequency selectivity and smaller in size in comparison with the conventional coupled line filter. A interdigital microstrip bandpass filter consists of quasi TEM-mode strip line resonators between parallel ground plant. Each resonator element is a quarter wavelength long of the center frequency and is short circuited at one end and open circuited at the other end. In the filter design, Ensemble software is used. Experimental results show that the bandwidth of interdigital microstrip bandpass filter is 2.52GHz, insertion loss is -1.8dB and return loss is -17.0dB at 11.20Hz.

• 한국정보통신설비학회:학술대회논문집
• /
• 2003.08a
• /
• pp.286-288
• /
• 2003

In this paper, in order to obtain a large differential phase shift with a little change in applied voltage, a ferroelectric reflective load circuit has been designed on top of barium strontium titanate $(Ba,Sr)TiO_3$ [BST] thin film. The design of the ferroelectric reflection-type phase shifter is based on a reflection theory of terminating circuit, which has a reflection-type analogue phase shifter with two ports terminated in symmetric phase-controllable reflective networks. To achieve large amounts of phase shift in low bias-voltage range, the effects of change of capacitance and transmission line connected with two coupled ports of a 3-dB $90^{\circ}$ branch-line hybrid coupler have been investigated. A large phase shift with a small capacitance change in the parallel terminating circuit has been demonstrated in the paper.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.4
• /
• pp.401-412
• /
• 2003

In this paper, a broadband phase shifter structure using a new switched network was proposed. A new reference network is composed of coupled lines and 45$^{\circ}$open and short stubs, which are shunted at the edge points of a main line, respectively, A delay network is composed of only a standard transmission line. It is possible to design a broadband 180$^{\circ}$phase shifter that phase dispersive characteristics by an impedance ratio R of coupled lines and greater phase dispersive characteristics by characteristic impedances Zm, Zs of a main line and stubs are used together. By considering a structure symmetry, the even and odd mode analysis was performed to obtain theoretical S-parameters of the proposed phase shifter. Also, through computer simulation on the basis of derived equations, design graphs were presented to optimally design a 180$^{\circ}$broadband phase shifter. Design graphs provide the values of characteristic impedances Zm, Zs, and I/O match and phase bandwidths. To verify electrical performances of the broadband phase shifter proposed in this paper, low different 180$^{\circ}$phase shifters, operated at the center frequency 3 GHz were designed and fabricated using design graphs, and were experimented. One of them was designed as a standard Schiffman structure to compare with electrical performances. Measured results of each phase shifter to satisfy simultaneously design conditions of I/O match （VSWR=1.15:1) and maximum phase deviation $({\varepsilon}_{{\Delta}{\phi}}＝{\pm}2^{\circ})$ were well in agreement with corresponding simulation results over impedance match and phase error bandwidths, and showed broadband characteristics.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.7 s.98
• /
• pp.681-689
• /
• 2005

This paper presents an ultra wide band(UWB) mixer using anti-parallel diode pair(APDP) with simulation and measurement results. The proposed mixer adopts the even-harmonic direct conversion mixing, which consists of a couple of filter, in-phase wilkinson power divider, wideband $45^{\circ}$ power divider, and APDP. The m mixer is operating over 3.1 to 4.8 GHz and producing quadrature(I/Q) outputs with a conversion loss of 18 dB and input third order intercept point($IIP_3$) of 15 dBm. I/Q outputs also have difference of about 0.5 dB and phase difference of ${\times}3^{\circ}$ and $P_{1dB}$ of 2 dBm.