• 펄프종이기술
• /
• 제30권2호
• /
• pp.5-12
• /
• 1998

Exploitation of the papermaking technology to reduce the strength loss that accompanies when using recycled papers as raw materials for papermaking is one of the most important issues imposed upon today's paper industry. Multi-layer sheet forming technology has been suggested as a way that provides some answers to this issue. In this study strength properties of single- and two-layer handsheets formed with recycled fiber and unbleached softwood kraft pulp have been examined to quantify the benefits when using two-layer sheet forming technology rather than a conventional single layer sheet forming precess. Single- and two-layer handsheets were made from 50% of OCC and 50% of Sw-UKP and their strength properties were evaluated. Also the strength properties made from Sw-UKP and OCC sheets were determined. A multihead, which can be attached on the top of hand- sheet former, was used to form two-layer sheets. Maximum strength properties could be obtained in the freeness range of 500∼300mL CSF for Sw-UKP Most of the strength properties was reduced by 30∼35% when 50% OCC was blended with UKP. Decrease of strength properties, however, could be reduced by employing a two-layer sheet forming method. Creator strengths could be obtained when UKP was positioned at the top layer of two layered sheets indicating greater UKP fines retention due to the filtration effect of the OCC layer formed prior to UKP layer contributed the strength improvement. Two-layer sheet showed lower Scott internal bond strength than single layer sheet. By incorporating some of UKP fibers into OCC layer this reduction could be reduced.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 1999년도 Pre-symposium of the 10th ISWPC Recent Advances in Paper Science and Technology
• /
• pp.386-389
• /
• 1999

Amphoteric polymers have brought to papermakers' attention gradually. In this paper, a series of amphoteric starches with different cationic and anionic degree of substitution (DS) are prepared. Better product has been selected and used under different condition. As retention and drainage aids, amphoteric starches were used in shorter fiber length, weak strength and poor drainage bleached AQ-Soda wheat straw pulp. In neutral and alkaline papermaking system, when amphoteric starches contain 0.024-0.026 anionic degree of substitution (DS), it is shown that the higher the cationic degree of substitution (DS) in amphoteric starches, the better the filler retention. The filler retention is improved 12.5%, 30.3%, and 35.1% and 32.5% respectively by adding 1% amphoteric starch LS-L2 -1 (0.034), LS-L2-2 (0.040), LS-L2-3 (0.047) and LS-L2-4 (0.052). But the strength of handsheets if affected a little. By adding 2% Al2 (SO4)3 and 1.5% LS-L2-3 at pH 7.5, filler retention can be improved from 38% to 80%, and breaking length of sheet only decreases 3.2%. As dry strengthening aids, amphoteric starches were used in eucalyptus APMP. Amphoteric starches are used in eucalyptus APMP. The amphoteric starch LS-L2-2 is better dry strength aid. Adding 1% LS-L2-2 can improve breaking length 24.5%, burst index 42.9%, tear index 38.8%, folding endurance and density of the handsheets.

• 펄프종이기술
• /
• 제47권5호
• /
• pp.98-103
• /
• 2015

The reduction of the energy consumption in papermaking process become more important issue because of the regulation of green house gas (GHG) emission. Since more than half of energy for papermaking process is consumed during drying process, the increase of the drying efficiency would be very important solution for saving energy and reduction of GHG emission. The improvement of drying efficiency could be very difficult for the liner board mill because the liner board are usually made of recycled paper, OCC (old corrugated container). The short fiber and fines originated the OCC lead to compact sheet structure and delay the water flow out during wet pressing process and drying process. The application of lignocellulose spacer could provide more loose wet sheet structure and result in the higher drainage rate and the improved drying efficiency. In this study, the effects of the application of lignocellulose spacer to the liner board mill were evaluated based on the mill trial. In order to overcome the common disadvantage of the spacer, the loss of strength properties, the spacer was pretreated with amphoteric polyelectrolyte during mill trial. The results showed the application of pretreated spacer improved the drying efficiency by reducing steam consumption. And the loss in the strength properties by the spacer could be supplemented by the pretreatment.

• 펄프종이기술
• /
• 제44권4호
• /
• pp.51-61
• /
• 2012

The new alkali pulping process combined with electron beam treatment was applied to utilize hemp bast tissues as a new valuable fibrous resource. Hemp bast tissues have some chemical properties with high lignin contents and holocellulose not to be defiberized by alkali pulping only, compared with the bast tissue of paper mulberry. To make up for the weakness of traditional alkali pulping process, electron beams were directly irradiated into the swelled bast tissue of hemp in NaOH solution and distilled water, and then facilitated the defiberization of hemp bast tissues. The papermaking from hemp bast fibers manufactured by the combination pulping process showed good apparent density, formation structure and air permeability, and had some mechanical properties with lower tensile, tear, burst strength and folding endurance. It is finally concluded that the combination pulping process with electron beam treatment could be suggested a new alternative for non-woody fibers.

• 펄프종이기술
• /
• 제38권4호
• /
• pp.17-23
• /
• 2006

Paper has fibers and fines network structure and it is strongly affected by interface bond-ing between fibers. Paper structural properties can be determined depending on the inter-fiber bonding. Fines play an important role in Campbell and consolidation effect through wet pressing and drying operations. The fines are essential for the formation of bonds between fibers and for the improvement of strength properties of papers. Since the fines are components of the pulp, there are always two factors to be considered: the quality and quantity of the fines. The quality of fines might be a potential variable to give a more accurate picture of the papermaking potential of the pulp. The object of this study is to investigate the effect of different types of pulp fines on the properties of paper and to access the potential of fines for controlling the bulk of paper. Refined Sw-BKP, Hw-BKP and BCTMP fines were used to investigate the fines effect. Wet-web strength, breaking length, scattering coefficient, and hydrodynamic specific volume, and drying shrinkage were measured. According to the results, chemical and morphological compositions of fines do not strongly affect to wet-web forming by their similar Campbell effect, but strongly affect to drying operation which forms hydrogen bonding among fiber-fines-fiber matrixes. Paper bulk should be controlled by the extent of hydrogen bonding between fibers during drying operation.

• 펄프종이기술
• /
• 제42권2호
• /
• pp.53-60
• /
• 2010

Kudzu vine (Pueraria lobata) is a perennial plant and spreads all around in South Korea. Recently the use of leaves, stems and roots of kudzu vine has been investigated in many fields. However, the research on kudzu fibers has not been performed in korean pulp and paper industry. As the stems and roots of kudzu were estimated to contain cellulosic fibers, the possibility of producing a raw material from kudzu fibers in pulp and paper mills was investigated in this study. The stems and roots of kudzu were collected in woods, and then the chemical composition and ash contents was measured. To acquire kudzu pulp, kraft pulping and bleaching of kudzu roots were carried out sequently. After making kudzu pulp, freeness and fiber length were measured, and handsheets was also prepared with kudzu pulp and the properties of handsheets were determined. Consequently, kudzu fibers have lower holocellulose contents than wood fibers and other non-wood fibers. Average fiber length is shorter than that of Sw-BKP, but shows the same level as that of Hw-BKP. The handsheet made from kudzu pulp shows the bulkier structure than those made from Hw-BKP and Sw-BKP.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 1999년도 Pre-symposium of the 10th ISWPC Recent Advances in Paper Science and Technology
• /
• pp.239-244
• /
• 1999

aluminum sulfate (alum) as a representative retention aid in papermaking processes was added to pulp suspensions, and the aluminum components adsorbed on the pulp were investigated quantitatively by two types of X-ray elementary analyses with regard to simultaneous changes of their surface charges. X-ray photoelectron spectroscopy (XPS) and X-ray fluorescence analysis (XFA) were applied to determine the aluminum components retained in pulp pads up to ca. 10 nm and 100${\mu}$m depth, respectively. In other words, XPS was utilized to analyze the outermost surface layers of the samples, and XFA was available for measurement of their extensive regions. A particle charge detector (PCD) was used to monitor streaming potentials at various pHs of the pulp mixtures under moderate sharing conditions. At pH 4.5 of pulp suspensions containing alum, surface charges of pulp fibers varied from negative to slight negative (approximately neutral) according to adsorption of aluminum components onto the pulp fibers. Subsequently, when a dilute NaOH solution in limited amounts was added to pulp mixtures, both streaming potentials and surface aluminum content of the pulp fibers increased distinctly although little total aluminum retention increased. Further addition of alkali solutions brought drastic decreases of the surface charges and surface aluminum content, while total aluminum content, on the contrary, increased gradually under neutral conditions. These results indicate that residual aluminum ions remained in pulp suspensions are predominantly adsorbed on surfaces of pulp fibers by adequate alkali additions and they must sufficiently cationize the fiber surfaces with increases of somewhat cationic aluminum complexes formed on the surfaces. On the other hand, aluminum components formed in higher pH ranges have nearly no contribution to improvement of charge properties of the pulp fiber surfaces, even though aluminum retention in pulp pads increases. XPS and XFA analyses combined with streaming potential measurement using a PCD suggest close relationships between aluminum content on the pulp fiber surfaces and their charge properties.

• 펄프종이기술
• /
• 제46권5호
• /
• pp.19-26
• /
• 2014

In-situ $CaCO_3$ formation on recycled wood pulp was studied to improve optical property and filler attachment to the fiber furnish in papermaking. We tried to attach calcium oxide (CaO) to the recycled fibers, old newspaper (ONP) in this case, by using selected polymers before in-situ $CaCO_3$ formation reaction on fibers, and then, $CO_2$ was injected to the furnish until all the CaO on fiber surfaces was consumed. It was found that the attachment of newly formed $CaCO_3$ to recycled fibers became stronger by attaching CaO to the fibers before in-situ $CaCO_3$ formation reaction. It was expected that the polymers used for the attachment of calcium source to the fiber furnishes helped to keep the newly formed $CaCO_3$ strongly attached to the fiber surface as well as to retain the impurities associated with calcium source and recycled fibers, if any. In-situ $CaCO_3$ formation gave higher brightness and much less ERIC value in ONP sheet than the case when the equivalent amount of GCC was added to the furnish.

• 펄프종이기술
• /
• 제34권4호
• /
• pp.1-6
• /
• 2002

In order to simulate the actual wet-end process in papermachine, RDA, a novel handsheet former, was used and following results were obtained. While the addition of polyelectrolytes gives significant effect on fiber flocculation, increase of stock consistency influenced on the formation of RDA sheets greatly. In particular, the consistency increase from 0.3 % to 0.4% abruptly increased floe size of RDA sheet and it results in severe deterioration of paper strength. Stock consistency, therefore, should be regarded as the most important factor in the formation simulation with RDA and should be controlled as the first sequence of tuning the operating conditions of RDA to simulate correctly the target machine paper's formation.

• 펄프종이기술
• /
• 제30권1호
• /
• pp.18-28
• /
• 1998

The main protein peak was observed in fraction No.9 and 109 when cellulase seperation was conducted by use of DEAE-Sephadex. The protein obtained from fraction No.9 has the characteristics of Cx component and that from fraction No.109 characteristics similiar to $C_1$ component. The effective reaction condition of the ensyme used was $40^{\circ}C$ in temperature. pH 5.0 and 90 minutes in treatment time. For the case of $C_1$ pH 5.5 in temperature range of $30^{\circ}C 50^^{\circ}C$, 4.0 5.5 in pH, and over 30 minutes of treatment time, the reaction was in the range of 80% of the maximum. Affinity of enzyme increased as freeness, increased, and this effect was more visible in fiber than in fines.