• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.1
• /
• pp.84-92
• /
• 2015

Fillers have been used to improve the optical and printing properties and to reduce the production cost while increasing the filler content in paper causes adverse effects on paper strength. In the previous study, it was shown that the thick stock addition of filler can increase the filler content without significantly sacrificing paper strength. This study was carried out to elucidate the effect of the location of starch addition (before or after the filler addition) on handsheet properties and a papermaking process as a part of developing the thick stock loading technology. In addition, effects of dual flow addition of cationic starch were evaluated. It was found that paper strength was superior when cationic starch was added after the filler addition. No adverse effects on optical properties, formation and filler retention were observed. Drainage was a bit slower when starch was added after the filler addition, which shall be resolved with regulating other factors. Dual flow addition of cationic starch before and after filler addition did not show any special advantage.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.3
• /
• pp.23-29
• /
• 2016

Effects of cationic polyvinylamine (PVAm) dry strength agent on effectiveness of optical brightening agent (OBA) during fine papermaking and the mechanism for brightness reduction of paper by PVAm was investigated by UV/Vis spectroscopy and turbidity measurement of OBA solution with PVAm. It was shown that PVAm reduced brightness of paper while opacity was not varied and tensile strength of paper was increased. Tetra-type OBA solution showed the peaks around the wavelength of 280 nm and 330 nm and the increase in the OBA concentration increased the UV absorbance in all wavelength. Addition of PVAm into the OBA solution decreased the UV absorbance at 280 nm. Turbidities of OBA and PVAm solutions were close to zero, respectively, while the turbidity value increased for the mixed solution of OBA and PVAm in various mixing ratios and the highest value was obtained when the mixing ratio of PVAm and OBA was 5:5, meaning that cationic PVAm formed complex with anionic OBA. In conclusion, cationic PVAm could form a complex with anionic OBA and that reduced UV absorbance, resulting in the reduced brightness of paper.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.3
• /
• pp.14-22
• /
• 2016

Pulping is a stage that can change fibrous raw materials into pumpable slurry. Recovered paper can be defibrated to individual fibers by shear stress generated by rotation of a rotor and water. Disintegration of recovered paper is more complicated than that of chemical pulp. When disintegration of recovered paper is poor, screening and cleaning efficiency will be worse and properties of paper will also be deteriorated. Therefore, pulping is an important treatment for improvement of availability of recovered paper and process runnability. In this study, degrees of disintegration of KOCC obtained from a linerboard mill was analyzed with a pilot-scale screen. Flake removal of KOCC slurry was performed by a pilot screen. Simple pumping action gave a positive effect on disintegration of KOCC. After pumping for 10 minutes, paper strength increased without the change of water retention value and fibrillation of KOCC slurry. This phenomena can be explained by modification of hornified surface of KOCC fibers by shear stress generated by pumping. Consequently, disintegration efficiency of KOCC can be enhanced by control of retention time at pulper or an agitation power at chests of papermaking process.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.5
• /
• pp.27-33
• /
• 2011

Hemp bast pulp cooked at temperature below $100^{\circ}C$ followed by defibration by the knife and the valley beater, respectively was mixed with softwood pulp varying the amount of hemp pulp in order to find the optimum condition for making hemp-wood paper. Both the knife and the valley beaters contributed to the dispersion of pulp fiber well. Lots of shives were found when the knife beater was applied exclusively, but the fibers were dispersed well when freeness dropped to 600 mL CSF and 500 mL CSF by the valley beater. Air resistance decreased drastically below 500 mL CSF where rapid disrupture of pulp fiber occurred. As the values for freeness and hemp fiber content increased, so did roughness and bulk. It was apparent that the tear strength of hemp-wood paper was on the rise drastically as hemp fiber content increased. Nevertheless the optimum hemp fiber content of hemp-wood paper would be 20% considering the decrease in both tensile and burst strengths as well as sheet formation.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.5
• /
• pp.59-65
• /
• 2009

Adsorption of an oil-proof agent (OPA）onto cellulose fibers during the papermaking process was investigated using UV-Vis spectrophotometry by measuring the OPA concentration decrease in the solution. From the calibration curve, the spectrum were converted to chemical concentrations in solution, from which the amount adsorbed onto the fiber surface could be determined. Thus, it was possible to determine the total amount adsorbed onto the fibers and in solution. Using this approach, we studied the adsorption behavior of the OPA onto the fiber surface and derived its, ${\Gamma}^s_t={\Gamma}^s_{\infty}(1-e^{-k_{\alpha}t})$. The values of the parameters kaand ${\Gamma}^s_{\infty}$ were determined using a mathematic model based on a mass transfer equation. Ultimately, a complete was derived: $Q={\alpha}{\cdot}\sum\limits_{i-1}^m{\pi}d_il_i{\cdot}M_A{\cdot}(1-e^{-k_{\alpha}t})/A_N$.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.2
• /
• pp.40-46
• /
• 1998

This study was aimed to investigate any improvement of dewatering and energy saving on the papermaking process when the various types of fillers were used, i.e., clay, talc and grounded calcium carbonate (GCC). Cationic polyelectrolyte and alum coagulants neutralized the surface charge of the filler particles and the filler particles were coagulated. The rates of dewatering and drying were investigated. The results indicated that clay tended to intense anion, while talc and GCC tended to anion trend nearly to neutrality. Clay and talc added with EPI-DMA, P-DADMAC and alum respectively as optimum levels showed a significant efficiency on the dewatering and the turbidity dissipation. However, the turbidity and dewatering rate of GCC decreased, when GCC was added with EPI-DMA and P-DADMAC respectively Drying rate of clay was increased when coagulant added. However drying rates of talc and GCC were not affected by coagulant, while the apprarent drying time of talc and GCC in the absence of any coagulant was shorter than the clay in the presence of a coagulant. The result confirmed that talc or GCC was more efficient than clay on the dewatering and drying, which is consistent with a general knowledge in the collodal science.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.1 s.113
• /
• pp.16-20
• /
• 2006

The effect of the freeness of pulp slurries on turbidity and transmittance of papermaking stocks was investigated using beaten bleached hardwood pulp stocks with freeness ranging from 651 mL to 403 mL CSF. Also the influence of fiber length on the turbidity and transmittance was examined with fractionated pulp stocks. Increases in stock consistency increased the turbidity. Transmittance of stock samples decreased, however, with the increase of stock consistency. Second order equations and exponential equations have been obtained as regression equations for the turbidity and transmittance of these stock samples, respectively.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.1 s.113
• /
• pp.54-61
• /
• 2006

Basically corrugated board is composed of three layers of different basis weight and stock composition. Warp is well-known for one of the most important problems of corrugated board production. Warp is caused by difference of hygro-expansibility of linears between top and bottom. This research was performed to evaluate the effect of paper properties on the warp of corrugated board. To evaluate warp, dynamic expansion properties of paper was tested using DPM(dynamic penetration measuring system). The effects of sizing, stock composition and wet-pressing on dynamic expansion properties were also evaluated. Commercial base papers showed different dynamic expansion property depending on stock composition and papermaking operation. Sizing treatment decreased and wet-pressing increased the amount of dynamic expansion. To reduce warp of corrugated board, management of dynamic expansion of base papers should be controlled by manipulating moisture, heat and tension, using a variety of adjustments available on the corrugator.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.3
• /
• pp.7-13
• /
• 2010

KOptimization and control of wet-end process provide a key solution to improve paper quality and production efficiency at the same time. Wet-end of paper machine is to determine three important influencing factors of papermaking i.e., retention, drainage and formation. Good formation of paper could be made at the cost of deteriorated retention or drainage. In the same manner increase of retention aid could cause the bad formation of paper. It is very important to find a proper retention chemical which may satisfy one of three factors without the sacrifice of other two. Laboratory scale analyzing or screening chemical additives of wet-end was reported in this study based on RDA sheet molding. Different from the conventional test method, simultaneous consideration of three important wet-end properties could be made by RDA and consequently more reliable prediction of actual paper machine wet-end could be expected.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.3
• /
• pp.50-57
• /
• 2010

A mill trial was performed in a kraft paper mill in order to evaluate the possibility of utilizing dual polymer dry strength aids system consisting of cationic PVAm and anionic PAM. It was found that the cationic PVAm - anionic PAM dry strength additives can improve paper strength without significantly disturbing the stability of the kraft papermaking process when virgin UKP was used as a furnish. Tensile strength (25.3% in machine direction, 48.4% in cross machine direction), elongation of paper (31.6%, 15.6%) and tensile energy absorption (48%, 54%) were improved. Air permeability of the kraft paper was improved as well (22%). Tear strength was decreased with PVAm dry strength aids system, but it can be compensated with decreasing refining degree. In addition, the mill trial results indicate that highly air permeable kraft sack paper can be produced by the addition of PVAm dry strength agents at the stock with reduced freeness.