• 대한전자공학회논문지TC
• /
• 제48권2호
• /
• pp.65-71
• /
• 2011

본 논문에서는 5-마이크로스트립선의 4-포트 다이플렉서에서 선간 간격을 조정 한 결과로부터 2번, 4번 선로 길이를 변동 시켜서 대역폭에 대한 변화를 알아보았다. 2번 선로 길이만을 조정한 경우 대역폭이 300MHz 축소되었으며 다이플렉서 특성을 한개 포트 입력에서만 구할 수 있었으나 2, 4번 선로 길이를 동시에 조정한 경우는 입력 포트 2개에서 모두 다이플렉서 특성을 얻을 수 있었다. 통과 대역에 대한 대역폭은 4번 선로의 변동 시 변경 전과 동일한 결과를 얻었다. 특히 저지대역에서는 선로 길이 조정 전보다 중심 주파수에서 출력 포트와의 이격도가 1번 포트 입력인 경우 41dB, 2번 포트 입력에 대한 출력 포트간 이격도는 32dB을 보인다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.163-170
• /
• 2005

In this paper, the rock bolts, soil nails with filling grout and the micro-piling with injecting grout by pressure were applied for the stabilization of the cut slopes consisting of sedimentary rocks, igneous rocks and metamorphic rocks respectively. The field measurements and 3-D FEM analyses to find out mobilized tensile stresses of the grouted-reinforcing members installed in the drilled holes were executed on each site. With assuming the increments of the cohesive strength in the improved ground, the back analysis using direct calibration approach of changing the elastic modulus of the ground was used to find out the improved elastic modulus which yields the same tensile stresses from field measurements. The results of back analysis show that the elastic modulus of the improved ground were 4 to 6 times as large as the elastic modulus of original ground. Consequently, the design for slope reinforcement to be more rational, it is proposed that not only the improved cohesive strength is to be used in the incremental ranges on well-known previous proposed data, but also the increased elastic modulus which is about 5 times as large as the original elastic modulus is to be considered in design.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2000년도 유체기계 연구개발 발표회 논문집
• /
• pp.122-128
• /
• 2000

Aerodynamic optimization of an automotive air-conditioning blower is a hard task because of the highly complex flow phenomena related to three-dimensional flow separations and the unsteady nature caused by the interaction between primary and secondary air flows throughout the fan. In this paper, an aerodynamic study on a forward-curved centrifugal fan has been carried out Firstly we obtained the fan performance curves versus flow rates showing its unstable nature in the surging operation range. Secondly aerodynamic characterizations were carried out by investigating the velocity and pressure fields in the casing flow passage using a 5-hole pilot probe, at different operating conditions. Surface flow pattern near the cut-off area exhibits similar flow behavior above the best efficiency operating point, although the pressure level increases substantially with the Increase of flow rate. Vorticity in the casing passage flow occurs in all (low rates, downstream from the r-Z plane $\theta$=120 deg., where the position of its core changes with the circumferential location. Although complex, the general flow behavior were common, giving insight in its main aerodynamic features.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.540-545
• /
• 2001

In case of small motors, coil bundle occupies a large portion of stator in view of mass and volume as well as dynamics. It is observed through modal test on the stator of an IPM BLDC (interior permanent magnet brushless direct current) motor that coil bundle wound on the stator core causes the first and second natural frequencies to decrease by about 20-30% compared with those of bare stator. Especially the third natural frequency is newly observed below 3 KHz, which is not observed on the bare stator. It is found that at the third mode the end-coil and the core vibrate out of phase in radial direction. In this paper, the stator is dynamically modeled in terms of the core and the coil bundle consisting of the end-coil and the slot coil based on the above observations for the prediction of dynamic properties. The core can easily be modeled using finite element method with its actual material properties and geometric shape. The concept of equivalent bending stiffness is used for modeling of the end-coil so that predictions may match with the measured natural frequencies for the end-coil cut out of the stator. Although the same concept can be applied to the slot coil, separation of the slot coil from the stator is impractical. Therefore, equivalent bending stiffness of the slot coil is determined through iterative comparisons with the measurements of natural frequencies of the stator with the slot coil in it.

• 한국정밀공학회지
• /
• 제19권3호
• /
• pp.101-106
• /
• 2002

This paper presents an experimental investigation of high speed machining of dies and molds. Several critical issues involved with the high speed machining of QRO90 tool steel of hardness up to HRc62, have been studied and explained from a detail analysis of experimental observations. The experiments were performed using ball end mills. The effect of different process parameters on tool life and surface finish produced was also investigated. The cutting parameters involved were; cutting speeds in the range of 100 to 40 / m/min, axial depth of cut from 0.1 to 0.5mm, pick feed of 0.1 to 0.5mm. Run out and acceleration signals were observed during the experiment to investigate cutting slates. Compressed air and flood coolant were used and the effect of coolant on tool life was also determined.

• 대한안전경영과학회지
• /
• 제2권3호
• /
• pp.101-115
• /
• 2000

Whenever a disaster occurs, people emphasizes that "Safety management is most important thing in the company". However, a situation of safety management is not changed dramatically after accidents in the past. Many small-and-medium sized industries neglect the importance of safety management. Current situation can be easily figured out when looks up an occurrence rate of accident, accident frequency rate and intensity rate. This paper investigated what workers of hotel-related industries think of a safety and types of accidents, effect of a safety education. On-site-survey was conducted for actual workers in four deluxe hotels and one condominium. 207 persons out of 400 people were replied. Statistical analysis was performed with SAS package about their reply. In injured type, cut from knife was most frequent. Main cause of accident was a unsafe posture and a unsafe behavior, so more safety education for these workers are necessary. In a physical pain which related with job, chronical pain was most dominant. As a result, a safety education has a high correlation with an experience of injured and treatment of safety, Cooking department has highest occurrence of accident than any other departments. Workers with an experience of five to ten years have most lowest treatment of safety, aid of safety education, safety feeling of their working environment, so peer attention must be put on these people to reduce accidents.accidents.

• 터널과지하공간
• /
• 제6권3호
• /
• pp.197-208
• /
• 1996

Due to the constraints in pre site-investigation for tunnel, it is essential to redesign the support structures suitable for rock mass conditions such as rock strength, ground water and discontinuity conditions for safe tunnel construction. For the selection of optimum support, it is very important to carry out the rock mass classification and in-situ measurement in tunnelling. In this paper, in a mountain tunnel designed by NATM in hard rock, the selectable system for optimum support has been studied. The tunnel is situated at Chun-an in Kyungbu highspeed railway line with 2 lanes over a length of 4, 020 m and a diameter of 15 m. The tunnel was constructed by drill & blasting method and long bench cut method, designed five types of standard support patterns according to rock mass conditions. In this tunnel, face mapping based on image processing of tunnel face and rock mass classification by RMR carried out for the quantitative evaluation of the characteristics of rock mass and compared with rock mass classes in design. Also, in-situ measurement of convergence and crown settlement conducted about 30 m interval, assessed the stability of tunnel from the analysis of monitoring data. Through the results of rock mass classification and in-situ measurement in several sections, the design of supports were modified for the safe and economic tunnelling.

• Nuclear Engineering and Technology
• /
• 제51권3호
• /
• pp.800-806
• /
• 2019

This paper presents a laboratory experiment on data acquisition technique that applied to the gamma radiation scanning coupled with computed tomography (CT) technique for inspection of broken nozzle inside the vertical vessel. The acquisition technique was developed to inspect a large diameter vessel when suspicious problem location is not easily accessed. This technique allows the installation of gamma radiation source (Cesium 137, Cs-137), and detectors (Sodium Iodine. NaI(Tl)) from the accessible location to the required location and performs the scanning by designed pattern. To demonstrate the designed technique, top opened tank which installed with six cut steel pipes diameter of 76.2 mm (3") at a certain position was selected. They were assumed to be a gas riser pipes inside the vessel. Three studied cases were performed, (a) projection of well installed six pipes, (b) projection of one out of six broken pipe and (c) one of nozzle was assumed to be failure and fell down until one out of six pipes was broken and obstructed by nozzle. Results clearly indicated the capability of developed technique to distinguish between normal situation case and abnormal situation cases.

• 한국해양공학회지
• /
• 제29권1호
• /
• pp.45-55
• /
• 2015

Because of the high stress concentration near the toe of a welded joint, the calculation of local stress using the finite element method which is relevant to the fatigue strength of the weld toe crack, is a challenging task. This is mainly caused by the sensitivity of finite element analysis, which usually occurs near the area of a dramatically changing stress field. This paper presents a novel numerical method through which a less mesh-sensitive local stress calculation can be achieved based on the 3D solid finite element, strictly sticking to the original definition of hot spot stress. In order to achieve the goal, a traction stress, defined at 0.5t and 1.5t away from the weld toe, was calculated using either a force-equivalent or work-equivalent approach, both of which are based on the internal nodal forces on the imaginary cut planes. In the force-equivalent approach, the traction stress on the imaginary cut plane was calculated using the simple force and moment equilibrium, whereas the equivalence of the work done by both the nodal forces and linearized traction stress was employed in the work-equivalent approach. In order to confirm the validity of the proposed method, five typical welded joints widely used in ships and offshore structures were analyzed using five different solid element types and four different mesh sizes. Finally, the performance of the proposed method was compared with that of the traditionally used surface stress extrapolation method. It turned out that the sensitivity of the hot spot stress for the analyzed typical welded joints obtained from the proposed method outperformed the traditional extrapolation method by far.

• 한국방재학회 논문집
• /
• 제10권3호
• /
• pp.91-100
• /
• 2010

본 논문에서는 절 성토 사면의 안정성에 영향을 미치는 영향인자의 민감도 분석을 수행하였다. 사면안정성 해석은 건기 및 우기조건, 지진시로 구별하여 해석하였다. 건기와 우기 조건에 대한 민감도 분석결과, 절토사면에서는 점착력, 내부마찰각, 단위 중량 등이 사면안정성에 미치는 영향은 우기조건 보다 더 큼을 알 수 있고, 성토사면에서는 건기와 우기조건에서 모두 유사한 영향을 주는 것으로 나타났다. 또한 수평지진계수는 전체사면에서 건기와 우기조건에 관계없이 유사한 값의 범위로 영향을 미치는 것으로 분석되었다. 강도정수인 점착력과 내부마찰각은 건기 및 우기조건에 관계없이 사면안정성에 단위중량, 지진계수에 비하여 상대적으로 큰 영향을 미치는 영향인자로 나타났다.