• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.204-205
• /
• 2018

This paper investigates CO₂ emission and cost analysis of blended concrete which was added with fly ash and slag. Three kinds of blended concrete were studied in this investigation, the first blended concrete was added fly ash replacing part of the cement while the second was added slag, the third was added fly ash and slag. Analysis result display that the blended concrete containing fly ash and slag is the optimal choice while considering economic and CO₂ emissions.

• Carbon letters
• /
• v.8 no.1
• /
• pp.1-5
• /
• 2007

The use of low cost and ecofriendly adsorbent has been investigated as an alternative to the current expensive method of removing dyes from wastewater. Cow dung cakes were collected from the nearby village which was burnt in a muffle furnace at $500^{\circ}C$ to obtain the required ash. This paper deals with the removal of Reactive Blue 221, Acidoll Yellow 2GNL and Olive BGL which are mainly used in textile industry, from aqueous solution by cow dung ash without any pretreatment. The adsorption was achieved under different pH, adsorbate concentration and the applicability of Langmuir and Freundlich isotherms were examined.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1992.04a
• /
• pp.35-40
• /
• 1992

Results of an experimental study on the manufacture, the workability and mechanical properties of steel fiber reinforced polyester resin composites utilizing industrial waste products are presented in this paper. The fly ash polyester resin composites using steel fiber, fly ash and calcium carbonic acid (CaCo3), unsaturated polyester resin, styrene monomer, cobalt octate and methyl ethyl ketone peroxide, fine and coarse aggregates are prepared with various filler~binder rations, binder rates and mixing conditions. As a test results, the workability of steel fiber reinforced polyester resin composites are considerably dropped with increasing fly ash-binder ratio and steel fiber volume. And compressive, flexural strength and bending toughness of the composites are remarkably improved with augmenting fiber contents.

• Computers and Concrete
• /
• v.6 no.1
• /
• pp.19-40
• /
• 2009

This paper describes the development of modified heat of hydration and maturity-strength models for concrete containing fly ash and slag. The modified models are developed based on laboratory and literature test results, which include different types of cement, fly ash, and slag. The new models consider cement type, water-to-cementitious material ratio (w/cm), mineral admixture, air content, and curing conditions. The results show that the modified models well predict heat evolution and compressive strength development of concrete made with different cementitious materials. Using the newly developed models, the sensitivity analysis was also performed to study the effect of each parameter on the hydration and strength development. The results illustrate that comparing with other parameters studied, w/cm, air content, fly ash, and slag replacement level have more significantly influence on concrete strength at both early and later age.

• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.811-816
• /
• 2000

This paper discussed hydrothermal reactivity of Ca(OH)2 and classified bituminous fly ashes which were collected at an electrostatic precipitator in coal fired power plant at 181$^{\circ}C$. The major products of hydrothermal reaction were tobermorite and hydrogrossularite because bituminous fly ashes contained Al2O3 content greater than 20 wt%. As increasing amount of Al2O3 content greater than 20 wt%. As increasing amount of Al2O3 in glass phases, formation of hydrogrossularite increased. Formation rate of crystalline tobermorite increased with content of finer particles, higher glass content and more Al2O3 in glass phases. There was a positive correlation between residue on 45${\mu}{\textrm}{m}$ sieve and hydrothermal reactivity of fly ash up to 3 hours. The hydrothermal reactivity of fly ash at 181$^{\circ}C$ for 12 hours was more affected by fineness than by glass content of fly ash.

• Textile Coloration and Finishing
• /
• v.9 no.6
• /
• pp.33-41
• /
• 1997

This paper surveys the extraction condition of polygenetic natural dye, Sappan Wood and the effect of ash to the dyeability and fastness. The appropriate time for extracting Sappon Wood was 1hour. The pH was increased as the amount of ash increase. The pH was nearly invariable according to the time of ash solution, the extracting times and temperature. Absorbance of dyeing fabrics was about 480nm. From the result of K/S value determination of fabrics, 10g/$\ell$ quantity of ash was surfficient for treatment and the amount of Sappon Wood was in 100% o.w.f.. K/S value of fabrics pre-mordanted or post-mordanted were higher than that of fabrics simultaneous mordanted.K/S value was increased as pH of mordanting bath decrease and pre-mordanting and post-mordanting fabrics increased the amount of absorption (K/S value) compared with non-mordanted fabrics. It was found that pH of mordanting bath affected the amount of absorption and color change of dyed fabrics. Light fastness of fabric dyed was very poor and the fastness of fabric dyed was not influenced by the mordanting conditions and methods.

• Computers and Concrete
• /
• v.2 no.5
• /
• pp.381-388
• /
• 2005

This paper presents the results of a study on binary blends of Portland cement and fly ash with complex admixture used for the concrete structures to meet specific performance objectives in east coastal area of China. The concretes were evaluated for workability, strength, water permeability, drying shrinkage, sulfate resistance and electrical resistance. Environmental Scanning Electron Microscopy (ESEM) was used to examine the microstructure of concrete made by complex admixture compared with control batches without complex admixture. The combined efforts of fly ash and complex admixture led to an improvement in the workability, strength and durability.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.3
• /
• pp.99-106
• /
• 2016

Our aim was to identify the potential of reed stalk as a raw materials for biomass pellet production. Compared to woody biomass, reed stalk contained significant levels of ash. The holocellulose content of reed stalk was similar to that of larch, but the lignin content of reed stalk was lower than that of larch. In the elemental analysis, chlorine content of reed stalk was much higher than that of larch, and satisfied only the mixed biomass pellet B of European non-woody pellet standards(EN 14961-6). In quantitative analysis of the ash, heavy metals contents of reed stalk satisfied European non-woody pellet standards. Higher heating value of oven-dried reed stalk pellet was slightly lower than that of larch wood pellet. The durability of reed stalk pellet was lower than that of larch wood pellet. The results of this study indicate that reed stalk might be used as a raw material of mixed biomass pellet B.

• Resources Recycling
• /
• v.25 no.6
• /
• pp.58-64
• /
• 2016

Paper industry discharges many by-products and quantity of PSA (Paper sludge ash) has been increased. In this study, hydration water was added to PSA for use as cement admixture. PSA with added water was mixed with anhydrite and this mixture was used as cement substitute. Physical properties of PSA cement were changed by contents of PSA, but PSA cement containing PSA less than 10% had similar properties to those of OPC. Compressive strength of PSA cement mortar had a certain relationship with $Ca(OH)_2$ content. Compressive strength at 3 days increased, as $Ca(OH)_2$ content increased. However, the strength at 28 days increased, as $Ca(OH)_2$ content decreased.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.479-484
• /
• 2006

The pore structures of paper were modified by the application of the blending of pulp, refining, and filler particle size and ash content. It was conformed that the reflectivity of paper can be modified by the combination of above parameters. It was also found that the modifications of reflectivity of paper were very close relation with pore structure, such as average pore size, pore size distribution and porosity. The average pore size was decreased with addition of HwBKP, but showed smaller particle size than those made from 100% HwBKP. Refining of pulp decreased both average pore size and the reflectivity of paper. The pore size distribution of filled paper can be varied by the combination of filler particle size and ash content.