활성탄에 의한 작용기가 다른 염료의 흡착: 파라미터 및 경쟁 흡착 (Adsorption of Dyes with Different Functional Group by Activated Carbon: Parameters and Competitive Adsorption)
-
- 공업화학
- /
- 제33권2호
- /
- pp.151-158
- /
- 2022
본 논문은 활성탄에 의해 작용기가 다른 말라카이트 그린(MG), 다이렉트 레드 81 (DR 81) 및 티오플라빈 S (TS)의 흡착에 대한 파라미터 특성(PH 효과, 등온선, 동역학 및 열역학 파라미터) 및 염료의 경쟁 흡착에 대해 조사하였다. Langmuir, Freundlich 및 Temkin 등온선 모델을 사용하여 염료의 흡착 메커니즘 및 활성탄에 의한 흡착 처리의 적합성을 평가했다. Langmuir 무차원 분리 계수 값은 활성탄에 의한 세 가지 염료의 흡착 처리가 효과적인 방법임을 나타내었다. 활성탄에 대한 세 가지 염료의 흡착 메커니즘은 Temkin 식에서 계산된 흡착열로부터 물리 흡착임을 확인하였다. 세 가지 염료의 흡착 동역학은 유사 2차 모델에 가까웠으며 잘 일치함을 보여주었다. 활성탄에 의한 세 가지 염료의 흡착 과정의 속도 지배 단계는 입자내 확산이었다. 양의 엔탈피와 엔트로피 변화는 각각 흡열 반응과 고액계면에서 흡착에 의한 무질서도가 증가함을 나타내었다. 세 가지 염료의 음의 Gibbs 자유 에너지 값은 온도가 증가함에 따라 자발성이 높아지는 것을 나타냈다. 삼성분 경쟁흡착에서 흡착능력이 높은 MG는 혼합용액에서 DR 81과 TS에 의해 약간의 방해를 받았으나, 흡착능력이 낮은 DR 81과 TS는 흡착력이 좋은 MG의 영향을 받아 흡착률이 크게 증가하였다.
Background: This paper deals with the study of natural radioactivity in rocks from Ogun State in Southwestern Nigeria. The aim is to determine radiation emissions from rocks in order to estimate radiation hazard indices. Objectives: The following objectives were targeted: 1. To determine radiation emissions from each type of rocks; 2. To estimate radiation hazard indices based on the rocks; 3. To correlate the activity concentrations of radionuclides with major oxides. Methods: The samples were analyzed using a NaI (Tl) gamma ray spectrometric detector and PerkinElmer AAnalyst 400 AAS spectrometer. Results: The activity of 40K, 226Ra, and 232Th were found in order of decreasing magnitude from pegmatite>granite>migmatite. In contrast, lower concentrations were found in shale, phosphate, clay stone, sandstone and limestone. The mean absorbed doses were 125±23 nGyh-1 (migmatite), 74±13 nGy/h (granite), 72±13 nGyh-1 (pegmatite), 64±09 nGyh-1 (quartzite), 45±16 nGyh-1 (shale), 41±09 nGyh-1 (limestone), 41±11 nGyh-1 (clay stone), 24±03 nGyh-1 (phosphate), and 21±10 nGyh-1 (sandstone). The outdoor effective dose rates in all rock samples were slightly higher than the world average dose value of 0.34 mSvy-1. The percentage composition of SiO2 in the rock samples was above 50 wt% except for in the limestone, shale and phosphate. Al2O3 ranged from 4.10~21.24 wt%, Fe2O3 from 0.39~7.5 wt%, and CaO from 0.09-46.6 wt%. In addition, Na2O and K2O were present in at least 5 wt%. Other major oxides, including TiO2, P2O5, K2O, MnO, MgO and Na2O were depleted. Conclusions: The findings suggest that Ogun State may be described as a region with elevated background radiation. It is recommended that houses should be constructed with good cross ventilation and residences should use home radiation monitoring instruments to monitor radon emanating from walls.
In this paper, twenty-five kinds of food presented in Sooljip(戌集) 5 and 6 of Food collections of 'Kosa-sibi Jip(攷事十二集)' have been classified into four : Staple food, subsidiary food, Tuck(rice cake) and Han-gwa(Korean confectionery), and Tang-jng and tea. Cooking processes have been examined and scientifically analyzed in terms of cooking, Fourteen kinds of Jook (thick gruel with cereal) as well as Urak-Jook were presented among the methods of making Jook, one of staple foods. Milk and ground rice were boiled together into Urak-Jook, which was nutritious because of carbohydrate, added to milk. Hong-sa Myun was mode of ground shrimps, ground bean, ground rice and flour which were kneaded together. It was a nutritiously balanced food. Nineteen kinds of Kimchi presented in this book were classified by the recipes. The five of Jook-soon Ja, U-so Ja, Tam-bok Ja and Jo-gang were made by adding red malt and cereals(boiled rice or candies). Jo-gang, Jo-ga and Jo-gwa-chae were made by adding salt and rice wine. With salt and fermenters added, eight were made. Chim-jup-jeo-ga was made by adding Jang(soy-bean sauce) and the inner chaff of wheat instead of salt. The four of Ka-za-san, Hwang-gwa-san, Tong-gwa-san and Jo-gang were made by adding salt and vinegar. Jo-gang was made by adding salt, rice wine, residue of rice wine and candies. The four of Kae-mal-ga, Ku-cho-chim-chae, Un-gu-hwa and Suk-hwa-chim-chim-chae were made by adding salt and spices. San-got-Kimchi was made without salt. San-got-Kimchi and Suk-hwa-chim-chae were made originally in Korea. Suk-hwa-chim-chae, in particular, was first classified as a kind of Kimchi in this book and oysters were added, which is notable. Pork could be preserved longer when smoked oven the weak fire of thatch ten days and nights. Dog meat was sauced and placed on the bones in a pot. A porcelain was put on the top of the pot. Flour paste sealed the gap between the porcelain and the pot. Some water was poured into the porcelain, and the meat was steamed, with two or three thatched sacks burned, which was a distilled dry steaming. This process has been in use up to now. Various cooking methods of chicken were presented from in Umsik-dimi-bang to in Chosun Musang Sinsik Yori Jebup. These methods were ever present regardless of ages. Such measuring units as Guin(斤) and Nyang(兩) were most frequently used in cooking processes of this book, except in case of Jang(soy bean sauce), vinegar and liquor. Twenty eight kinds of kitchenware and cookers were used, of which porcelains wee most used and pans and sieves followed. The scientific eight cooking methods were as follows. First, salt was refined through saturated solution. Next, it was recommended Hong-sa Myun containing shrimps should not be taken along with pork, which is thought to be a proper diet in terms of cholesterol contained by shrimps and pork. Third, meat was coated with thin gruel and quickly roasted and cleared of the dried gruel membrane, which prevented nutrients from exuding and helped to make the meat well-done. Fourth, The fruit of paper mulberry trees has the protease which can soften meat. Therefore when meat was boiled with th fruit of paper mulberry trees, it can be softened easily. Fifth, pork was smoked over the weak fire of thatch. Sixth, in cooking dog meat, distilled dry steaming raised the boiling point and made it possible to preserve meat longer. Seventh, in boiling the sole of a bear, lime was added, which made meat tender by making the pH lower or higher than that of raw meat. Finally, in boiling down rice gluten, a porcelain in the pot prevented boiling over the brim, which is applied to pots in which to boil medical herbs.
The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70
The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70
Plasma disruption in tokamak experiments is a challenging issue that causes damage to the device. Reliable prediction methods are needed, but the lack of full understanding of plasma disruption limits the effectiveness of physics-driven methods. Data-driven methods based on supervised learning are commonly used, and they rely on labelled training data. However, manual labelling of disruption precursors is a time-consuming and challenging task, as some precursors are difficult to accurately identify. The mainstream labelling methods assume that the precursor onset occurs at a fixed time before disruption, which leads to mislabeled samples and suboptimal prediction performance. In this paper, we present disruption prediction methods based on anomaly detection to address these issues, demonstrating good prediction performance on J-TEXT and EAST. By evaluating precursor onset times using different anomaly detection algorithms, it is found that labelling methods can be improved since the onset times of different shots are not necessarily the same. The study optimizes precursor labelling using the onset times inferred by the anomaly detection predictor and test the optimized labels on supervised learning disruption predictors. The results on J-TEXT and EAST show that the models trained on the optimized labels outperform those trained on fixed onset time labels.
우리나라 서해안(西海岸)에 자생(自生)하는 내염성식물(耐鹽性植物) 10종(種)에 대한 proline함량(含量)은
한반도 동남부 일대에 발견된 제4기 단층인 상천, 입실, 왕산단층 비 지대에서 단층운동과 이에 수반된 유체의 영향으로 생긴 미구조 및 광물학적인 변화 양상을 알아보기 위해 단층 비지와 주위 모암의 전암분석과 전자현미분석이 수행되었다. 단층 비지와 주위 모암의 X-선형광분석 결과 유동성이 낮은 원소 즉
The purpose of this study was to investigate the bonding of resin- based root canal sealer, AH26 when the sealer was applied as a thin layer between dentine and gutta-percha surface. In this study forty non-caries extracted human molars and resin-based root canal sealer(AH 26, DeTrey/Dentsply, Germany) were used. Disks of gutta-percha, 6mm in diameter.6mm thick (Diadent/Dentsply, Korea) for thermoplastic obturation were used and dentin surfaces were treated with 2% NaOCl(Group 1) or 2%NaOCl+17% EDTA(Group 3). Disks of gutta-Percha, 6mm in diameter.6mm thick (Diadent/Dentsply, Korea) for conventional obturation were used and dentin surface were treated with 2% NaOCl(Group 2) or 2%NaOCl+17% EDTA(Group 4). Enamel was removed by a horizontal section 1mm below the deepest portion of the central occlusal groove by using a watercooled low speed diamond saw. A second horizontal section was done around cementoenamel junction. Exposed dentin surface was cut to approximately
하계 동해의 기원 해수 T-S diagram 방법에다 용존 산소를 추가시키고, 자료를 위도-경도 평면상에서 표시하는 방법으로 기원해수를 판별하였다. 하계에 동해에서 총 8개의 기원해수가 판별되었다. 표층해수로는 1) 고온-저염의 EKCW, 2) 고온-최저염의 NKSW, 3) 고온-고염의 MTSW, 4) 저온-저염의 TSCW의 4종류와 5) 최고염의 TMW, 6) 저온-저염-고농도의 산소를 가지는 LCW인 2종류의 중층수 그리고 심층수로 7) 저온-고염-고농도의 산소를 가지는 ESIW, 8) 최저온-고염-저농도의 산소를 가지는 ESPW 8종류로 구분할 수가 있었다. 특히, 동해 중 북부 해역에서 발견된 최저염의 NKSW(North Korea Surface Water), 기존에 알려진 대마난류 표층수에 비해 고염의 특징을 보여준 MTSW(Modified Tsushima Surface Water), 그리고 타타르 해협에서 시베리아 연안을 따라 남하하는 TSCW(Tatar Surface Cold Water)등이 이번 연구에서 새롭게 정의되었다. 조성비로 본 기원 해수의 흐름 총 8개의 기원해수에 대해 조성비 50% 이상을 기준으로 한 각 기원해수의 흐름을 Fig. 7에 나타내었다. 먼저 표층의 흐름을 보면, EKCW는 대한해협 서수도를 통해 동해 연안을 따라 북상하는 흐름을 보였고, MTSW는 대단해협 동수도를 통해 동해로 진입하여