• 한국식물병리학회지
• /
• 제14권6호
• /
• pp.720-724
• /
• 1998

Open-top field chamber study was carried out to investigate effect of ambient ozone level on the yield of rice cultivar 'Dongjin' in Kwangyang area located in the vicinity of the industrial complex of Yechon petrolium refinery and chemical works or Kwangyang Iron and Steel works during the summer of 1997. mean ozone concentration of ambient air during daytime (9:00∼17:00) was revealed to exceed over 40 ppb which is defined to be a critical level causing plant injury and yield reduction in Europe. Yield component analysis showed that there was no significant difference in rice yield between ambient air and charcoal-filtered air. The results suggest that the ambient ozone levels during the exposure period had no effect on yield reduction of rice cultivar 'Dongjin' and it is likely that the cultivar is tolerant to ambient ozone levels.

• 한국작물학회지
• /
• 제46권2호
• /
• pp.78-83
• /
• 2001

Two rice cultivars of the japonica type, ozone-resistant Ilpumbyeo (IL) and ozone-susceptible Keu-mobyeo#l (KM) were exposed to ozone ($O_3$) at 0.15 ppm for 30 days. The available nutrient regimes were varied by doubling the supply of nitrogen (N), phosphorus (P) and potassium (K) within a basic fertilizer status (N, P, K; 15, 12, 12 kg l0$a^{-1}$). There was little difference on plant height between ozone-treated and nontreated plants. The most significant ozone stress on tiller number was shown on the 30th day of ozone exposure. Slight recovery from ozone stress was noted on the 60th day. On the 30th day, tiller number was greatly decreased by 40.8% in IL and 64.6% in KM, whereas at a high nitrogen supply regime (2N), it was decreased by 21.4% in IL and 42.7% in KM as compared to the control not treated with ozone at basic fertilizer status. The inhibition of tiller production caused by ozone exposure was alleviated on the 60th day. In both cultivars, number of spikelets per plant and weight of 100 grains were affected little by the ozone treatment irrespective of nutrient regime. However, the number of panicles per plant and yield were reduced significantly. In both cultivars, yield of ozone-treated plants with 2N status was 12.4-16.1 % higher than that of the ozone-treated plants with basic nutrient status. A significant yield decrease of 47.8% and 33.4% was observed for IL and KM, respectively, in ozone-treated plants with higher potassium (2K) status.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제4C권5호
• /
• pp.201-206
• /
• 2004

In order to investigate the optimum conditions for the effective ozone formation in a dielectric barrier discharge, measurements of ozone concentration were carried out for various conditions such as the gap length, the dielectric material and the operating gas. It was found that the optimum discharge conditions differed exceedingly in the types of operating gases and dielectric materials. In dry air, dielectric material with low dielectric constant and thermal conductivity, which might contribute to the restriction of the gas temperature rise in the discharge region, proved effective in obtaining both high ozone yield and concentration. The optimum gap length was considered to be in the range of 600-800 mm. In oxygen, using a quartz glass disk as a dielectric material, the required condition to obtain the high ozone yield and concentration was expanded.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2214-2216
• /
• 2005

This paper is researched discharge and ozone generation characteristics of ozonizer using $Al_2O_3$ Ceramic dielectric. The discharge characteristics with variation of the discharge electrode area is studied. The characteristics of ozone concentration. ozone generation and ozone yield were measured to discharge power, discharge electrode area and supplied gas flux for oxygen and air. The solubility of ozone for water concentrations and ozone generations proportional to discharge power and discharge electrode area. Ozone yield has slowly increase with Increasing discharge power at high flow-rate. As the result, the maximum values of ozone characteristics ozone generation and ozone yield, can be obtained 5817[ppm] and 36[g/kWh]. We make enough the ozone concentration as the air in the home. An electric discharge electrode area is apt to shrink gradually into a miniaturization trend of the ozonizer but the enlargement of the occurrence flight of the electric discharge area gives the characteristic enhance the aid in the identity condition through the structure improvement.

• 조명전기설비학회논문지
• /
• 제29권12호
• /
• pp.77-82
• /
• 2015

Ozone is a powerful disinfectant and oxidizing agent, and it is used in a wide range of applications, such as waste water treatment, food processing, etc.. There is also a great potential of using ozone in new emerging medical applications, such as ozone dentistry and ozone oxygen therapy. For these purposes, simple, small, compact and efficient sources of ozone are needed. In this study, in order to increase the current-voltage range of the discharge and to avoid the overheating of the gas in the ozonizer we suggested ozonizer of injection needle and plate electrode type(INP Type) with the gas through the needle. A ozonizer of INP type have been investigated by focusing on ozone concentration and yield according to flow rates and Gap of two electrodes. The results of studies of ozone production for DC corona discharge in oxygen at atmospheric pressure about the ozonizer of INP type. The ozone concentration and the generation yield increased as the gap of two electrodes and gas flow were decreased. Also, when the gap of two electrodes and gas flow with no change, the ozone concentration and generation yield each have variation of direct proportion and inverse proportion with discharge voltage.

• 펄프종이기술
• /
• 제34권4호
• /
• pp.22-29
• /
• 2002

This research was conducted to investigate the morphological characteristics of fine fibers produced during beating process of high yield pulp treated with ozone and the distribution of lignin in the produced fine fibers. Thermomechanical(TMP) pulp and chemithermomechanical(CTMP) pulp of spruce and CTMP of white birch were beaten to reach 200$m\ell$ CSF, and then the fine fibers were observed using ultraviolet microscope. The fine fibers produced from TMP and CTMP of spruce using treated with ozone for 15 minutes were fragments of fiber surfaces or cell corners, and most of them contained lignin. However, lignin was not observed in the fibers after 15 minutes of ozone treatment. The fine fibers produced from CTMP of white birch were broken pieces or fragments of fiber surfaces or cell corners. The lignin was observed in the fibers until 5min of ozone treatment but no lignin was observed after 5 minutes of ozone treatment. Different morphological characteristics of TMP and CTMP explained both the different morphological characteristics and the distribution of lignin observed in the fine fibers produced from the beating process of TMP and CTMP treated with ozone.

• Journal of the Korean Wood Science and Technology
• /
• 제25권2호
• /
• pp.75-80
• /
• 1997

This research has been examined to measure the degree of the fiber damage of ozonenation high yield pulp in the beating process. Ozone treated the TMP(Thermomechanical Pulp) and CTMP(Chemithermomechanical Pulp) of spruce and the CTMP of birch has been beaten to be reached 200ml(freeness) of its content. It had been studied the forming of fiber distribution by treatment for long fiber, short fiber, fine with the above method. As ozone treatment time gets longer, the pulp has showed the tendency of increasing the fiber content of 28, 48mesh. Ozone treated fiber has been increased long fiber content by being added softness. By given longer ozone treatment time, the TMP and CTMP of spruce has showed the decreasing of fiber content. On the contrary, CTMP of birch has showed the increasing its fiber content. It had proved that the results of difference are rather closer to the species of tree than closer to the kinds of pulp. The fiber content of over 200mesh which has created in beating process demonstrates the decreasing of its fiber content by getting longer ozone treatment time. The softness of fiber can be extracted by the lignin of fiber surface that had been formed by ozone treatment. Thus we assume that the fiber in the process of beating obtains less physical damage.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권8호
• /
• pp.468-476
• /
• 2000

Nowadays, ozone is mainly utilized for water treatment and home equipments. Although the demand for ozone is increasing, the ozone yield of silent discharge type ozonizer is low. Therefore, it is expected to improve the energy efficiency and ozone yield of an ozonizer. In this paper, a new ozone generation system is proposed. The 60[Hz] three-phase voltage is applied to three-phase superposed discharge type ozonizer(3PSDO) which has three electrodes(central, internal and external electrodes). There is no discharge pause time when three-phase voltage is applied due to 120-degree phase difference of applied voltage. The synergy effect of the three-phase superposed discharge type ozonizer is investigated by comparing with the three sort of single-phase discharge type ozonizer(1PDO). So, three-phase superposed discharge type ozonizer is able to obtain high ozone yield, and optimize discharge space, because this can increase the discharge power at low applied voltage.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2001년도 학술대회논문집
• /
• pp.135-138
• /
• 2001

Recently, ozone is utilized In various fields and its needs are expanding. therefore, so many ozone generation methods have been reported in the latest years, its main purpose Is to get the high ozone concentration and to improve the ozone yield. One of them is a plate-type ozone generator. In this paper, the plate-type ozone generator is piled up many folds(3 and 5 electrodes). Ozone concentration and yield were investigated in accordance with power, quantity of supplied gas and gap spacing of plate electrodes.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제11C권4호
• /
• pp.113-119
• /
• 2001

This paper presents a model for a pin-to-cylinder discharge type ozonizer, which utilizes the superposition of surface discharge and corona discharge operation. By changing the gas flow rate, the discharge power and the number of SDO units, the characteristics of ozone concentration ( $O_{3con}$), ozone generation ( $O_{3g}$) and ozone yield ( $O_{3Y}$) were investigated. Using one SDO unit the maximum values of $O_{3con}$, $O_{3g}$ and $O_{3Y}$ were found as 8100[ppm], 1623[mg/h] and 213[g/kWh] respectively. With two SDO units the corresponding values were found as 12800[ppm], 2893[mg/h] and 248[g/kWh] respectively. Hence using two SDO units the efficiency was improved by 16[%].y 16[%].