• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.56.1-56.1
• /
• 2009

The intermediate operating temperature of solid oxide fuel cells (IT-SOFCs) have achieved considerable importance in the area of power fabrication. This is because to improve materials compatibility, their long-term stability and cost saving potential. However, to conserve rational cell performance at reduced-temperature regime, cathode performance should be obtained without negotiating the internal resistance and the electrode kinetics of the cell. Recently, double perovskite structure cathodes have been studied with great attention as a potential material for IT-SOFCs. In this study, double-perovskite structured cathodes of $GdBaCoCuO_{5+\delta}$, $GdBaCo_{2/3}Cu_{2/3}Fe_{2/3}O_{5+\delta}$ compositions and $(1-x)GdBaCo_2O_{5+\delta}+xCe_{0.9}Gd_{0.1}O_{1.95}$ (x = 10, 20, 30 and 40 wt.%) composites were evaluated as the cathode for intermediate temperature solid oxide fuel cells(IT-SOFCs). Electrical conductivity of the cathodes were measured by DC 4-probe method, and the thermal expansion coefficient of each sample was measured up to $900^{\circ}C$ by a dilatometer study. Area specific resistances(ASR) of the $GdBaCo_{2/3}Cu_{2/3}Fe_{2/3}O_{5+\delta}$ cathode and 70 wt.% $GdBaCo_2O5+\delta$ + 30wt.% Ce0.9Gd0.1O1.95 composite cathode on CGO electrolyte substrate were analyzed using AC 3-probe impedance study. The obtained results demonstrate that double perovskite-based compositions are promising cathode materials for IT-SOFCs.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1999년도 춘계학술발표강연 및 눈문개요집
• /
• pp.128-128
• /
• 1999

• Journal of Electrochemical Science and Technology
• /
• 제2권1호
• /
• pp.32-38
• /
• 2011

The composite barium strontium cobalt ferrite (BSCF) cathodes were investigated in the intermediate temperature range of solid oxide fuel cells (SOFCs). The characteristics and electrochemical performances of composited BSCF/samarium doped ceria (SDC); BSCF/gadolinium doped ceria (GDC); and BSCF/SDC/GDC were compared to single BSCF cathode. The BSCF used in this study were synthesized using glycine nitrate process and mechanically mixing was used to fabricate a composite cathode. Using a composite form, the thermal expansion coefficient (TEC) could be reduced and BSCF/SDC/GDC exhibited the lowest TEC value at $18.95{\times}10^{-6}K^{-1}$. The electrochemical performance from half cells and single cells exhibited nearly the same trend. All the composite cathodes gave higher electrochemical performance than the single BSCF cathode (0.22 $Wcm^{-2}$); however, when two kinds of electrolyte were used (BSCF/SDC/GDC, 0.36$Wcm^{-2}$), the electrochemical performance was lower than when the BSCF/SDC (0.45 $Wcm^{-2}$) or BSCF/GDC (0.45 $Wcm^{-2}$) was applied as cathode ($650^{\circ}C$, 97%$H_2$/3%$H_2O$ to the anode and ambient air to the cathode).

• International Journal of Precision Engineering and Manufacturing-Green Technology
• /
• 제5권5호
• /
• pp.637-642
• /
• 2018

The impact of the sintering process, especially in terms of sintering temperature and sintering aid concentration, on the ohmic transport and electrode performance of $(La_{0.80}Sr_{0.20})_{0.95}CoO_{3-{\delta}}$-gadolinia-doped ceria (LSCF-GDC) cathodes is studied. The ohmic and charge-transfer kinetics exhibit a highly coupled $Co_3O_4$ concentration dependency, showing the best performances at an optimum range of 4-5 wt%. This is ascribed to small grain sizes and improved connection between particles. The addition of $Co_3O_4$ was also found to have a dominant impact on charge-transfer kinetics in the LSCF-GDC composite layer and a moderate impact on the electronic transport in the current-collecting LSCF layer. Care should be taken to avoid a formation of excessive thermal stresses between layers when adding $Co_3O_4$.

• Journal of Electrochemical Science and Technology
• /
• 제13권3호
• /
• pp.407-415
• /
• 2022

Surface coating of cathodes is an essential process for all-solid-state batteries (ASSBs) based on sulfide electrolytes as it efficiently suppresses interfacial reactions between oxide cathodes and sulfide electrolytes. Based on computational calculations, Li₃PO₄ has been suggested as a promising coating material because of its higher stability with sulfides and its optimal ionic conductivity. However, it has hardly been applied to the coating of ASSBs due to the absence of a suitable coating process, including the selection of source material that is compatible with ASSBs. In this study, polyphosphoric acid (PPA) and (NH₄)₂HPO₄ were used as source materials for preparing a Li₃PO₄ coating for ASSBs, and the properties of the coating layer and coated cathodes were compared. The Li₃PO₄ layer fabricated using the (NH₄)₂HPO₄ source was rough and inhomogeneous, which is not suitable for the protection of the cathodes. Moreover, the water-based coating solution with the (NH₄)₂HPO₄ source can deteriorate the electrochemical performance of high-Ni cathodes that are vulnerable to water. In contrast, when an alcohol-based solvent was used, the PPA source enabled the formation of a thin and homogeneous coating layer on the cathode surface. As a consequence, the ASSBs containing the Li₃PO₄-coated cathode prepared by the PPA source exhibited significantly enhanced discharge and rate capabilities compared to ASSBs containing a pristine cathode or Li₃PO₄-coated cathode prepared by the (NH₄)₂HPO₄ source.

• 한국세라믹학회지
• /
• 제47권1호
• /
• pp.26-38
• /
• 2010

Degradation in Solid Oxide Fuel Cell performance can be ascribed to the following fundamental processes from the materials chemical point of view; that is, diffusion in solids and reaction with gaseous impurities. For SOFC materials, diffusion in solids is usually slow in operation temperatures $800\sim1000^{\circ}C$. Even at $800^{\circ}C$, however, a few processes are rapid enough to lead to some degradations; namely, Sr diffusion in doped ceria, cation diffusion in cathode materials, diffusion related with metal corrosion, and sintering of nickel anodes. For gaseous impurities, chromium containing vapors are important to know how the chemical stability of cathode materials is related with degradation of performance. For LSM as the most stable cathode among the perovskite-type cathodes, electrochemical reduction reaction of $CrO_3$(g) at the electrochemically active sites is crucial, whereas the rest of the cathodes have the $SrCrO_4$ formation at the point where cathodes meet with the gases, leading to rather complicated processes to the degradations, depending on the amount and distribution of reacted Cr component. These features can be easily generalized to other impurities in air or to the reaction of nickel anodes with gaseous impurities in anode atmosphere.

• 전기화학회지
• /
• 제13권3호
• /
• pp.169-174
• /
• 2010

Sulfur cathodes were prepared by ball milling method with different types of electronic conductors and binders in different ball milling time. The sulfur cell with a cathode prepared in 45 min ball milling time gave an initial discharge capacity of 794mAh/g with Super-P as an electronic conductor and poly(vinylidene fluoride) as a binder. The cathode with multi-walled carbon nanotube as an electronic conductor showed an initial discharge capacity of 944 mAh/g and a discharge capacity of 300 mAh/g after 20 cycles. Cathodes with poly(ethylene oxide) and poly(vinylidene fluoride) as binders showed different cycle performance.

• 산업기술연구
• /
• 제42권1호
• /
• pp.7-12
• /
• 2022

High nickel layered oxide cathodes are gaining increasing attention for lithium-ion batteries due to their higher energy density and lower cost compared to LiCoO₂. However, they suffer from the formation of residual lithium on the surface in the form of LiOH and Li₂CO₃ on exposure to ambient air. The residual lithium causes notorious issues, such as slurry gelation during electrode preparation and gas evolution during cell cycling. In this review, we investigate the residual lithium issues through its impact on cathode slurry instability based on deformed polyvinylidene fluoride (PVdF) as well as its formation and reduction mechanism in terms of inherently off-stoichiometric synthesis of high nickel cathodes. Additionally, new analysis method with anhydrous methanol was introduced to exclude Li⁺/H⁺ exchange effect during sample preparation with distilled water. We hope that this review would contribute to encouraging the academic efforts to consider practical aspects and mitigation in global high-energy-density lithium-ion battery manufacturers.

• 전기화학회지
• /
• 제2권4호
• /
• pp.202-208
• /
• 1999

[ $50/50 vol\%$ ] LSM-YSZ의 양극은 콜로이드 증착법에 의해 YSZ 전해질상에 증착하였다. 양극 특성은 주사전자현미경과 임피던스 분석기에 의해 고찰하였다. LSM-YSZ양극의 제조 조건에 따른 영향을 관찰하였으며, 그 영향에 대한 개선책이 고체산화물 연료전지의 성능향상을 위해 제시되었다. 임피던스에 대한 온도, YSZ전해질로의 양극 접착에 대한 표면 오염, 사용하는 Pt 페이스트, 미세구조에 대한 곡표면에 가해진 연무질 분사기술과 셀과 셀의 변동성에 대한 영향들은 각각 $900^{\circ}C$ 측정, YSZ표면 연마, 일단의 Pt페이스트 사용, 평편한 YSZ판의 사용과 일관된 절차와 기술의 사용에 의해 해결되었다. 이때 재현성 있는 임피던스 스펙트럼들이 향상된 셀을 사용함으로써 얻어졌고, $900^{\circ}C$에서 (공기)LSM-YSZ/YSZ/LSM-YSZ(공기) 셀에 대해 측정된 전형적인 임피던스 스펙트럼들은 2개의 불완전한 호로 구성되었다. 또한 LSM-YSZ 양극의 임피던스 특성은 촉매층, 양극 조성, 인가 전류 등과 같은 실험 조건들에 의해서도 영향을 받았다.

• 전기화학회지
• /
• 제14권3호
• /
• pp.176-183
• /
• 2011

본 연구에서는 Sr이 치환된 이중층 페로브스카이트($SmBa_{0.5}Sr_{0.5}Co_2O_{5+{\delta}}$, SBSCO)와 전해질 물질로 사용되는 $Ce_{0.9}Gd_{0.1}O_{2-{\delta}}$ (CGO91)을 기반으로 한 중 저온형 고체산화물 연료전지 (ITSOFC) 복합공기극의 분말 크기와 열 사이클에 대한 전기화학특성을 연구하였다. 복합공기극의 모체가 되는 SBSCO에 CGO91물질을 이용하여 면적비저항을 확인 한 결과 약 $0.54\sim9.04{\mu}m$의 분말 크기를 보이는 SBSCO와 $0.4\sim42{\mu}m$의 분말 크기를 보인 CGO91이 각각 50 wt%로 구성된 SBSCO : 50 복합공기극이 600 및 $700^{\circ}C$에서 약 0.102 및 $0.013{\Omega}cm^2$의 우수한 면적비 저항을 가지는 것을 확인 하였으며 상대적으로 분말 크기가 큰 CGO91 분말을 이용한 두 개의 공기극의 경우 $700^{\circ}C$에서 약 $0.260{\Omega}cm^2$와 $0.055{\Omega}cm^2$의 특성을 보여주었다. 10회에 걸친 열 사이클실험을 통하여 SBSCO : 50의 면적비저항은 $0.0193{\Omega}cm^2$에서 $0.094{\Omega}cm^2$로 증가하였으며 7회 이후의 면적비저항은 일정하게 유지됨을 확인하였다.