• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.5
• /
• pp.309-317
• /
• 2004

This paper suggested the vibration characteristic improvement by variation mode of ring type ultrasonic motor. Design for the piezoelectric ceramic and elastic body of stator were calculated by the finite element method(FEM) that consider the resonance frequency, vibration mode and coupling efficiency etc. Through the result of vibration analysis from 6 order mode to 8 mode, the 7 order mode was gained very an excellent results that it was the coupling efficient, minimum power loss and bending vibration value. Here over 7 order mode, this paper was acquired that an output current for input voltage was very a large increased results. The result of vibration calculation, from thickness 0.5[mm] to 2[mm], knew the fact that the vibration displacement at 0.5[mm] is an high value too. From such result, this paper was manufactured the ultrasonic motor of outer diameter 5O[mm] , inter 22[mm] having the about 43.86[KHz] resonance frequency. We have gated that a simulation result is 42.2[KHz] and an experiment result is 43.86[KHzl The propriety of this paper was established though comparison. investigation of simulation and experiment result.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.1
• /
• pp.167-174
• /
• 2005

The design for cold extrusion dies is very important, because the die insert is subjected to very high radial and hoop stresses. The design of cold extrusion dies has many constrained conditions. In this paper, the used assumptions are such that the yield strength of each ring is selected according to the allowable tensile or compressive hoop stress in each ring and the maximum allowable inner pressure, when yielding occurs in one ring of the dies, is obtained by the proposed equation. In order to obtain design variables, such as diameter ratios and interferences, using the maximum inner pressure, the flexible tolerance method was used for shrink-fitted thick-walled cylinders. ANSYS APDL was used to perform the repeated analysis of deformation of the dies due to the variation of the design variables. The response surface methodology is utilized to analyze the relationship between the design variables and the maximum radial displacement of the die insert during extrusion. From the results, it is found that outer diameter of the die insert has the largest effect on the minimization of maximum radial displacement at the inner surface of the dies.

• Korean Journal of Optics and Photonics
• /
• v.8 no.2
• /
• pp.107-110
• /
• 1997

We generated a diffraction free beam from Nd:YAG laser with an NBUR (negative branch unstable ring) resonator. The field inside the resonator had a plane wavefront and a homogeneous intensity distribution and the output beam through a scraper mirror of an annular type was used as a source. The outpur beam had an inner radius of 2.5 mm and an outer radius of 5 mm. In this experiment, we used a Fourier transformation lens with the focal length of 5 m to observe the far-field pattern. The lens was placed at a distance of the focal length from the scraper mirror and we found that the beam did not show any noticable diffraction over the distance of 13 m from the lens.

• 대한공업교육학회지
• /
• v.35 no.2
• /
• pp.224-237
• /
• 2010

When the underwater structure sails high speed, noise and vibration propagate to the sensor in the nose of the dome. In this paper, to avoid this kind of noise and vibration CRP(Carbon Reinforced Plastic) material and SNORE ring(Self-NOise REduction Ring) are attached at the curved structure and simulates its isolation characteristics using commercial software. Vibration displacement and stress are calculated at the planar sensor array. The material of the curved structure is aluminum and maximum outer diameter is 53Omm, 215mm in length, 270mm in planar diameter, respectively. Based on the simulation results, reduction ratio of the received normal stress at the sensor is above 95% at the frequency of 12kHz and 15kHz. At the mid point of the planar sensor the normal stress is higher than 20mm and 40mm apart. This results can be used to increase the sensitivity of the acoustic sensor as a basic data.

• 정보저장시스템학회:학술대회논문집
• /
• 2005.10a
• /
• pp.113-118
• /
• 2005

Small form factor optical disks for near-field optics using solid immersion lens were developed. Disk durability properties in terms of head-disk interface (HDI) properties were investigated by drag test, diamond like carbon film and lubricant film were coated on the small form factor disk to enhance HDI. Disks with glass substrates and lubricant films after heat treatment showed more durable characteristics. Coverlayers made of UV resin were uniformly coated by spin coating In which the ski-jump could not be formed by adopting outer ring technique.

• Journal of the Korean Ceramic Society
• /
• v.25 no.1
• /
• pp.78-82
• /
• 1988

Good quality LiNbO3 single crystals which can be applied to SAW devices, were grown by Czochralski method. It was observed that the gas-bubbles were concentrated in ring shape at the outer part of grown crystals, and this anomaly was illustrated by modeling the mechanism of gas-bubble entrapment according to the melt flow pattern in the crucible. And this mechanism was also encertained by observation of solid-liquid interface shape of grown crystals. The optimal condition for good quality crystals was known that the solid-liquid interface shape was slightly concave.

• Journal of the Korean Chemical Society
• /
• v.52 no.4
• /
• pp.356-361
• /
• 2008

• Journal of KSNVE
• /
• v.9 no.2
• /
• pp.393-400
• /
• 1999

Defect frequencies of rolling element bearings are experimentally investigated utilizing the two-sided directional spectra of the complex-valued vibration signals measured from the outer ring of defective bearings. The directional spectra make it possible to discern backward and forward defect frequencies. The experimental results show that the directional zoom spectrum is superior to the conventional spectrum in identification of bearing defect frequencies, in particular the inner race defect frequencies.

• Transactions of the Society of Information Storage Systems
• /
• v.2 no.1
• /
• pp.26-31
• /
• 2006

Small form factor optical disks for near-field optics using solid immersion lens were developed. Diamond like carbon film and lubricant film were coated on the small form factor optical disk to enhance the head-disk interface(HDI) characteristics. The disk durability properties in terms of HDI phenomena were investigated by drag test. Disks with glass substrates and the lubricant films experienced heat treatment showed more durable characteristics. Coverlayers made of UV resin were uniformly coated by spin coating in which the ski-jump could be removed by adopting outer ring technique

• Bulletin of the Korean Chemical Society
• /
• v.14 no.5
• /
• pp.631-635
• /
• 1993

The polarizability and the transition state energy of a cephalosporin are assumed to be theoretical indices of the permeability through the outer membrane and of reactivity of ${\beta}$ -lactam ring with penicillin binding proteins, respectively, in Gram-negative bacteria. They are computed by AM1 method and used as variables of quantitative structure-activity relationship study. The results justify quadratic dependence of the activity on the variables. The intersection of difference volumes between $\beta-lactamase$ stable cephalosporins and unstable ones manifests that the steric hindrance of 7-side chain is responsible for the ${\beta}$ -lactamase stability.