• Journal of Sensor Science and Technology
• /
• v.30 no.6
• /
• pp.384-387
• /
• 2021

Cyclic voltammetry (CV) is a powerful electrochemical measurement technique that can determine redoxable substances in a solution. The advantage of CV is that we can observe redox behavior over a wide potential range in a short time. Because of its practicality and versatility, CV is used not only in electrochemistry but also in various fields of chemistry, such as inorganic chemistry, organic chemistry, and biochemistry. As technology advances and the popularity of CV grows, the need for trained electrochemists also increases. However, most students do not receive formal training in these technologies as part of their curriculum. There are few concise and accessible resources for learning CV. Therefore, this manuscript provides a brief introduction to cyclic voltammetry to aid readers in collecting and interpreting useful data from cyclic voltammograms.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.376-376
• /
• 2011

I-III-VI2 chalcopyrite compounds, particularly copper, indium, gallium selenide(Cu(InxGa1-x)Se2, CIGS), are effective light-absorbing materials in thin-film solar application. They are direct band-gap semiconductors with correspondingly high optical absorption coefficients. Also they are stable under long-term excitation. CIS (CIGS) solar cell reached conversion efficiencies as high as 19.5%. Several methods to prepare CIS (CIGS) absorber films have been reported, such as co-evaporation, sputtering, selenization, and electrodeposition. Until now, co-evaporation is the most successful technique for the preparation of CIS (CIGS) in terms of solar efficiency, but it seems difficult to scale up. CIS solar cells have been hindered by high costs associated with a fabrication process. Therefore, inorganic colloidal ink suitable for a scalable coating process could be a key step in the development of low-cost solar cells. Here, we will present the preparation of CIS photo absorption layer by a solution process using novel metal precursors. Chalcopyrite copper indium diselenide (CuInSe2) nanocrystals ranging from 5 to 20nm in diameter were synthesized by arrested precipitation in solution. For the fabrication of CIS photo absorption layer, the CuInSe2 colloidal ink was prepared by dispersing in organic solvent and used to drop-casting on molybdenum substrate. We have characterized the nanoparticless and CIS layer by XRD, SEM, TEM, and ICP.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.12
• /
• pp.1106-1110
• /
• 2005

We fabricated (110) silicon hard master by using anisotropic wet etching for embossing. The etching chemical for the silicon wafer was a TMAH $25\%$ solution. The anisotropic wet etching produces a smooth sidewall surface and the surface roughness of the fabricated master is about 3 nm. After spin coating an organic-inorganic sol-gel hybrid material on a silicon substrate, we employed hot embossing technique operated at a low pressure and temperature to form patterns on the silicon substrate by using the fabricated master. We successfully fabricated the multi-mode planar optical waveguides showing low propagation loss of 0.4 dB/cm. The surface roughness of embossed patterns was uniform for more than 10 times of the embossing processes with a single hydrophobic surface treatment of the silicon hard master.

• Journal of the Korean Ceramic Society
• /
• v.42 no.10 s.281
• /
• pp.645-648
• /
• 2005

To fabricate a (100) silicon hard master, we used anisotropic wet etching for the embossing. The etching chemical for the sili­con wafer was a TMAH 25$\%$ solution. The anisotropic wet etching produces a smooth sidewall surface inclined at 54.7°, and the surface roughness of the fabricated master is about 1 nm. After spin coating an organic-inorganic sol-gel hybrid resin on a silicon substrate, we used the fabricated master to form patterns on the silicon substrate. Thus, we successfully obtained patterns via the hot embossing technique with the (100) silicon hard master. Moreover, by using a single hydrophobic surface treatment of the master, we succeeded in achieving uniform surface roughness of the embossed patterns for more than ten embossments.

• Proceedings of the KIEE Conference
• /
• 2002.11a
• /
• pp.164-166
• /
• 2002

Over the past two decades, the electrochemical supercapaictors are receiving growing attention due to their possible applications as power backup in electronic equipment and electrical vehicles. Both of amorphous cobalt oxide and manganese dioxide were prepared by sol-gel process reported in our previous work. Nano-structured supramolecular oligomer of 1,5-diamino anthraquinone(DAAQ) coated metal oxides were successfully prepared by electrochemical oxidation from an acidic non-aqueous medium. We established process parameters of the technique for the formation of nano-structured materials. Furthermore, improved the capacitive properties of the nano structured metal oxide electrodes using controlled solution chemistry. $CoO_2$ and $MnO_2$-based composite electrode showed relatively good electrochemical behaviors in acidic electrolyte system with respect to specific capacity and scan rate dependency

• Bulletin of the Korean Chemical Society
• /
• v.19 no.9
• /
• pp.947-951
• /
• 1998

$K_2NiF_4$-type layered compounds of the ($C_nH_{2n+1}NH_3)_2SnCl_4$ (n=2, 4, 6, 8, and 10) system have been synthesized from a stoichiometric mixture of $SnCl_2$ and alkyl ammonium salt using a low temperature solution technique under the inert atmosphere condition. Their crystal structures are assigned to the orthorhombic system by X-ray powder diffraction analysis. The a and b cell parameters show small changes. However, the c parameter is varied significantly according to the increment of alkyl chains of the organic layer which is located between inorganic layers in the compounds. The conformational phase transitions of the compounds are studied by the DSC in the temperature range of 300 to 500 K. FT-IR and Raman spectra are analyzed in the ranges of 1300 to 4000 cm-1 and of 50 to 360 $cm^{-1}$ with Ar-laser (λ=514.5 nm) excitation, respectively. Photoluminescence phenomena are observed for some compounds. The bond-length of Sn-Cl is determined by the EXAFS spectroscopic analysis.

• Journal of the Korean Ceramic Society
• /
• v.40 no.7
• /
• pp.690-695
• /
• 2003

Soft-solution route employing PVA(Polyvinyl Alcohol) as a polymeric carrier in a mixed metal cation solution was used for synthesis of single-phase nickel aluminate (NiA1$_2$O$_4$) powders. The PVA ensured the homogeneous distribution of metal ions in the solution and it resulted in the decrease of crystallization temperature. The synthesized powders prepared by PVA addition were soft and ball-milled easily. The ball-milled powders of about 300 nm in size were fully densified to density of 4.35 g/㎤ at 1600$^{\circ}C$ for 1 h. The Vickers hardness, flexural strength, fracture toughness and thermal expansion coefficient of the sintered nickel aluminate were 14.2 ㎬, 304 ㎫, 4.8 ㎫$.$m$\^$1/2/ and 9.8${\times}$10$\^$-6//$^{\circ}C$, respectively.

• Polymer(Korea)
• /
• v.35 no.6
• /
• pp.605-609
• /
• 2011

Composite nanofibers were prepared by electrospinning and thermal treatment from poly (vinylidene fluoride) (PVDF)-$SiO_2$ blend solution. The nanofibers were stacked on layers to produce fully interconnected pores. TEM micrographs and EDX spectra confirmed the presence of $SiO_2$ in the composite nanofibers. The porosity of nanofibers was effectively enhanced by the introduction of electrospinning technique. ATR-FTIR and XRD results revealed that PVDF in the composite nanofibers exhibited the mixture crystal structure of ${\alpha}$-phase and ${\beta}$-phase. The crystal structure of ${\alpha}$-phase and crystallinity increased by the thermal treatment. In addition, the mechanical properties, thermal stability and hydrophobicity were markedly amplified by the thermal treatment.

• Journal of Chest Surgery
• /
• v.24 no.3
• /
• pp.229-244
• /
• 1991

A bioassay technique and organ bath study were performed to analyze the effects of extracellular $Ca^{2+}$ and $Ca^{2+}$-antagonists on endothelium-derived relaxing factor[s][EDRF] released from the endothelial cells of rabbit aorta. Transverse strips with intact endothelium or damaged endothelium were used for the mechanical contraction experiment using organ bath. Long segment including thoracic and abdominal aorta with endothelium [EDRF donor aorta] was perfused with Tyrode solution which was aerated with 95% $O_2-5%$ $CO_2$ mixed gas and kept at 35oC. The perfusate was bioassayed with a transverse strip of thoracic aorta with damaged endothelium. The test strip was contracted with nor-epinephrine and acetylcholine was used to stimulate the release of EDRF from endothelial cells. The results obtained were as follows; 1] The endothelium-dependent relaxation[EDR] induced by acetylcholine was biphasic; an initial rapid relaxation followed by a slow relaxation. 2] EDR induced by acetylcholine was reduced gradually with the decrease in the concentration of extracellular $Ca^{2+}$. The effect of extracellular $Ca^{2+}$ on EDR was more prominent in the late slow relaxation phase. 3] EDR to acetylcholine was not altered by acute exposure to organic $Ca^{2+}$-antagonists. Pretreatment with verapamil to the EDRF donor aortic segment did not alter the magnitude of EDR. 4] Among the inorganic $Ca^{2+}$-antagonists $Mn^{2+}$ and $Cd^{2+}$ did not inhibit EDR, whereas $Co^{2+}$ and $La^{3+}$ inhibited EDR. 5] The inhibitory response of $Co^{2+}$ to EDR developed when infused directly on the test strip. That of $La^{3+}$, however, was evoked when added to solution perfusing the donor aortic segment. The above results suggest that $Ca^{2+}$-antagonists do not affect EDR and the inhibitory effect of $Ca^{2+}$ results from influencing the action of EDRF on vascular smooth muscle, whereas that of $La^{3+}$ results from its action on the release of EDRF from endothelial cells.

• Applied Chemistry for Engineering
• /
• v.18 no.1
• /
• pp.17-23
• /
• 2007

For the purpose of antibacterial and photocatalystic deodorization functions, the papermaking inorganic fillers and pigments were surface-modified with Ag nano-colloidal solution and $TiO_2$ by using the hybridization technique. The functional specialty sheets and coating papers were produced with the surface-modified fillers and pigments, and evaluated by halo test and inhibition growth test in their antibacterial and photocatalystic characteristics. For the application of specially produced antibacterial handsheet to the wallpaper usages, the photocatalyst efficiency test of benzene in volatile organic compound dissolution experiment of antibacterial and deodorization function wallpaper showed that the efficiency was 45~50% for 80 min of reaction time and 90% of attained resolution was reached at approximately 30 min of response time.