• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.6 no.1
• /
• pp.55-66
• /
• 1996

This study was conducted to evaluate breakthrough characteristics of respirator cartridge using multi-organic vapors, including carbon tetrachloride, trichloroethylene, and toluene. The organic vapors were used as single phase, binary system, and ternary system. The results are summarized as follows. 1. Organic vapors studied were 1,000 ppm, 750 ppm, 500 ppm and 250 ppm in single phase. Carbon tetrachloride having the highest molecular weight showed the breakthrough first, and breakthrough sequency by organic vapor was dependent on its molecular weight. The 10% breakthrough times at 1,000 ppm of organic vapor were 97 minutes for carbon tetrachloride, 129 minutes for trichloroethylene and 135 minutes for toluene. 2. When concentrations of organic vapors were at levels of the Threshold Limit Values, the lives of the respirator cartridges were 122 hours in carbon tetrachloride, 18 hours in trichloroethylene and 28 hours in toluene. 3. In the binary system at a total concentration of 1,000 ppm with carbon tetrachloride and trichloroethylene, breakthrough times ranged from 104 minutes to 125 minutes, which were longer than 97 minutes in a single phase (1,000 ppm) for carbon tetrachloride, but shorter than breakthrough times for TCE and Toluene. 4. Breakthrough times in the binary system with carbon tetrachloride and toluene were 131~132 minutes. 5. Breakthrough times in the ternary system with carbon tetrachloride, toluene, and trichloroethyl ene were $120{\pm}8$ minutes, which were longer than 97 minutes in the single phase (1,000 ppm) for carbon tetrachloride, equal to 129 minutes for trichloroethylene, and shorter than 135 minutes for toluene. Those were almost similar to $124{\pm}9$ minutes of breakthrough times in the binary systems.

• Land and Housing Review
• /
• v.2 no.1
• /
• pp.87-92
• /
• 2011

The anaerobic digestion of food waste effluent through single- and two-phase process was estimated and compared in this study. The treatment efficiencies for total solid(TS), volatile solid(VS), tCOD(total COD) and sCOD(soluble COD) were invariably higher in the single-phase process, which was accounted for by the fact that the treatment efficiency of organic wastes usually showed an inverse relationship with organic loading rate in the anaerobic digestion. In fact, the organic loading rate was lower for single-phase process. The concentration of tCOD were significantly lower in two-phase process but much more biogas was produced, compared to single-phase anaerobic digestion process, which might be explained partly by the relatively higher stability of two-phase process resulting from the separation of acid phase from methane phase.

• Journal of the Korean Physical Society
• /
• v.73 no.11
• /
• pp.1729-1734
• /
• 2018

Organic-inorganic halide perovskite single crystals undergo phase transition of being cubic, tetragonal, or orthorhombic depending on the temperature. We investigated the $CH_3NH_3PbBr_{3-x}I_x$ single crystals grown by the inverse temperature crystallization method with temperature-dependent UV-Vis absorption and photoluminescence. From the temperature-dependent absorption measurement, the optical band gap is extracted by derivation of absorption spectrum fitting and Tauc plot. In our results, $CH_3NH_3PbBr_{3-x}I_x$ single crystals show that an abrupt change in optical band gap, PL peak position and intensity appears around 120 K - 170 K regions, indicating the phase transition temperature.

• Nuclear Engineering and Technology
• /
• v.51 no.3
• /
• pp.761-768
• /
• 2019

Understanding the phenomena of formation of single drops is necessary to understand the hydrodynamics in solvent extraction equipment which are used for separation of nuclear materials. In this work, the phenomena of aqueous phase and organic phase drop formation at submerged nozzles are compared by conducting experiments with 30%TBP (v/v) in dodecane as the organic phase and nitric acid as the aqueous phase. Two different nozzles and three different nitric acid concentrations are used. For each nozzle and nitric acid concentration, velocity of the dispersed phase is varied. Drops of aqueous phase formed at downward oriented nozzles submerged in organic phase are observed to be smaller than the drops of organic phase formed at upward oriented nozzles submerged in aqueous phase. Correlations to estimate drop diameter are proposed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.537-537
• /
• 2012

We have studied a fabrication of vapor phase polymerized Poly(3,4-ethylenedioxythiophene) (PEDOT) nanowire arrays for the first time. The vapor-phase polymerization (VPP) technique is a bottom-up processing method that utilizes the organic arrangement of macromolecules to easily produce ordered aggregates, including on the nanoscale, or prepare thin films of self-assembled molecules, micropatterns, or modified microstructures of pure conducting polymers. Also, liquid-bridge-mediated nanotransfer molding (LB-nTM), which was reported as a new direct patterning method recently, is for the arrayed formation of two- or three-dimensional structures with feature sizes as small as tens of nanometers over large areas up to 4 inches across and is based on the direct transfer of various materials from a mould to a substrate through a liquid bridge between them. The PEDOT nanowires grown by VPP method and transferred on a substrate to use LB-nTM method have been fabricated to single crystal PEDOT nanowires investigated Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Selected Area Electron Diffraction (SAED), X-Ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), and electrical properties.

• Journal of Microbiology and Biotechnology
• /
• v.4 no.3
• /
• pp.204-209
• /
• 1994

The synthesis of N-(benzyloxycarbonyl)-L-aspartyl-L-phenylalanine methylester (Z-APM), a precursor of aspartame, from N-(benzyloxycarbonyl)-L-aspartic acid (Z-Asp) and L-phenylalanine methylester hydrochlolide($L-PM\cdot HCI$) was investigated in a saturated-ethylacetate single phase system using immobilized thermolysin. Among the various supports tested, glyceryl-CPG was found to be most efficient for retaining enzyme activity. The enzyme immobilized onto glyceryl-CPG also showed the highest activity for Z-APM synthesis in saturated ethyl acetate. Z-APM conversion yield in saturated ethylacetate was half of that obtained in an ethyl acetate-buffer two-phase system under the same reaction conditions. However, as the mole ratio of $L-PM \cdot HCI$ to Z-Asp was increased to 4.0, the conversion yield reached 95 %. When continuous synthesis of Z-APM was canied out in a plug flow reactor (PFR) with 80 mM of L-PMㆍHCI and 20 mM of Z-Asp in saturated ethylacetate (pH 5.5), more than 95 % of Z-Asp was converted to Z-APM with a space velocity of 1.16 $hr^{-1} at 40^{\circ}C$. Although the operational stability in PFR was reduced rapidly, more than 80% of initial activity was maintained in CSTR even after a week of operation.

• Journal of the Korean Ceramic Society
• /
• v.37 no.7
• /
• pp.665-672
• /
• 2000

The ferroelectric YMnO3 thin films were prepared by MOD(metal-organic decomposition) method with Y- and Mn-acetylacetonate as starting materials. Thin films were grown on various substrates by spin-coating technique. The crystalline phases of the thin films were identified by X-ray diffractometer as a function of heat-treatment temperature, pH of coating solution and substrate. In addition, the effect of Mn/Y molar ratio(0.8~1.2) on the formation of hexagonal-YMnO3 phase was investigated. In forming highly c-axisoriented hexagonal-YMnO3 single phase, the Pt coated Si substrate was more effective than the bare Si substrate, and the optimum heat-treatment condition was at 82$0^{\circ}C$ for 30 min. Higher Mn/Y molar ratio within 0.8~1.2 and pH of YMnO3 precursor solution within 0.5~2.5 favored formation of ferroelectric hexagonal phase rather than orthorhombic phase. Leakage current density of the hexagonal-YMnO3 thin film formed on Pt(111)/TiO2/SiO2/Si substrate was low enough as 0.4~4.0$\times$10-8(A/$\textrm{cm}^2$) at 5 V and its remanent polarization(Pr), calculated from the P-E hysteresis loop, was 3 nC/$\textrm{cm}^2$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.637-637
• /
• 2013

We develop single-crystal poly(3,4-ethylenedioxythiopene nanowires using liquid-bridge-mediated nanotransfer printing via vapor phase polymerization. This direct printing method can simultaneously enable the synthesis, alignment and patterning of the nanowires from molecular ink solutions. Twoor three-dimensional complex structures of various single-crystal organic nanowires were directly fabricated over a large area using many types of molecular inks. This method is capable of generating several optoelectronic devices. LB-nTM is based on the direct transfer of various materials from a mold to a substrate via a liquid bridge between them. To demonstrate its usefulness, we used LB-nTM to fabricate nanowire field-effect transistors and arrays of 6,13-bis (triisopropyl- silylethynyl) pentacene (TIPS-PEN) nanowire field-effect transistors.

• International Journal of Internet, Broadcasting and Communication
• /
• v.7 no.2
• /
• pp.155-160
• /
• 2015

The objective of this study was to develop the classification method of various organic wastes. Specifically, the effects of proximate composition on the biogas production and degradation rates of agricultural by-production was investigated and a new standards for mixture of various organic wastes based on proximate composition combination was developed. Agricultural by-products (ABPs) with medium total carbohydrate, medium crude protein and low fat contents demonstrated the single step digestion process. ABPs with low total carbohydrate, high crude protein and high fat contents demonstrated the two step digestion process of Diauxic growth. The single ABP (Class No. 15) and the mixed ABPs (Class No. 12+18, 6+12+22, 9+12+18) after 10days showed the similar biogas yield pattern. We can use the classification method for the more ABPs and organic wastes from factory and municipal waste treatment plant for the high efficient biogas production.

• Journal of the Korean institute of surface engineering
• /
• v.23 no.2
• /
• pp.1-10
• /
• 1990

Metal-Organic Vapor Phase Epitaxy (MOVPE) is an epitaxial process utilizaing ane or more of organometallice as reactnte to grow compound semicond semiconductror layers. MOVPE is basically a cold wall process in which reactants are delivered without reacting with each other to the heated substrate where reactants are thermally decomposed to from compound semiconductors through chemical reaction. Since reactants are delivered as gas phase and the formation of the single crystal compunds depends on the thermal decomposition of the reactants, details of MOVPE relies on the hydrodynamics and pyroltsis and chemical reation of reactants inside on reaction chamber. It has been demonstrated that MOVPE is capable of growing virtually all of the III-V, II-VI and IV-VI compound semiconductrs, fabricating ultrathin epilayers, for ming abrupt hetrointerfaces with monolayer transition width, and is suitable for multi-wafer operation yilding a high throghtput. Overiew of reactror componts and layer, characteristics, and status of MOVPE are discussed.