• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.29 no.3
• /
• pp.310-321
• /
• 2019

Objectives: The purpose of this study was to investigate types and characteristics of chemical substances used in LCD(Liquid crystal display) panel manufacturing process. Methods: The LCD panel manufacturing process is divided into the fabrication(fab) process and module process. The use of chemical substances by process was investigated at four fab processes and two module processes at two domestic TFT-LCD(Thin film transistor-Liquid crystal display) panel manufacturing sites. Results: LCD panels are manufactured through various unit processes such as sputtering, chemical vapor deposition(CVD), etching, and photolithography, and a range of chemicals are used in each process. Metal target materials including copper, aluminum, and indium tin oxide are used in the sputtering process, and gaseous materials such as phosphine, silane, and chlorine are used in CVD and dry etching processes. Inorganic acids such as hydrofluoric acid, nitric acid and sulfuric acid are used in wet etching process, and photoresist and developer are used in photolithography process. Chemical substances for the alignment of liquid crystal, such as polyimides, liquid crystals, and sealants are used in a liquid crystal process. Adhesives and hardeners for adhesion of driver IC and printed circuit board(PCB) to the LCD panel are used in the module process. Conclusions: LCD panels are produced through dozens of unit processes using various types of chemical substances in clean room facilities. Hazardous substances such as organic solvents, reactive gases, irritants, and toxic substances are used in the manufacturing processes, but periodic workplace monitoring applies only to certain chemical substances by law. Therefore, efforts should be made to minimize worker exposure to chemical substances used in LCD panel manufacturing process.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.spc8
• /
• pp.3057-3062
• /
• 2011

We have synthesized and characterized the first cyclic co-oligomeric ferroelectric liquid crystals (FLCs) based on cyclic siloxanes and found that the co-oligomer containing two different mesogenic units exhibits $SmC^*$ mesophase over a wide temperature range from $65^{\circ}C$ to $135^{\circ}C$, much wider than those of the monomer counterparts and the cyclic homo-oligomers. The cyclic co-oligomeric liquid crystal readily filled the display cell and exhibited fast switching times in the range of 4 ms to 6 ms over the entire $SmC^*$ phase. Moreover, the practical absence of layer shrinkage, attributed to de Vries-type transition, shows an additional significant advanage for cyclic co-oligomeric FLCs in LCD applications.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.3
• /
• pp.153-157
• /
• 2010

We studied the adsorption efficiency of steelmaking slag in removing volatile organic compounds (VOCs) for increasing the recycling rate of steel-making slag. Ceramic filter was prepared by mixing the steel-making slag and the diatomite which is used as adsorbents due to the advantage of the high specific surface area and regular mesopores. The adsorption efficiency for VOCs removal was about 80%, 96% and 85% in acetaldehyde, formaldehyde and ammonia, respectively. The adsorption efficiency over 80% for all The gases showed the practical possibility as the adsorption filter.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.4
• /
• pp.170-177
• /
• 2012

Amethyst gems represents thermal effects of far-infrared emission, promotes the body's metabolism, and attracts attention as an eco-friendly interior material. In this paper, amethyst increase the value of jeweling by applying the characteristic purple motif, furthermore, I will intend to develop of design model. Metal crafting of brooch & necklace in the works performed based on the organic three-dimensional shape of the Rhino CAD Data. It was made possible through the precise laminated wax processing and then combining the amethyst. I researched the ornament modeling by applying the 'Golden Ratio', and suggesting utilizing method for interior jewel modeling, and also, is expected that this paper on the amethyst modeling design can contribute to the manufacturers' productivity.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.5
• /
• pp.247-252
• /
• 2002

$(Pb_{1-x}La_x)TiO_3$ (x = 0.1) thin films were prepared on ITO-coated glass substrates by metal organic chemical vapor deposition using ultrasonic spraying. Effects of the post-annealing and the seeding layer on crystallization, microstructures and electrical properties of thin films were investigated. Dielectric constants of films increased due to the modification of crystallization and the changing of a surface morphology by applying the post-annealing. In addition, as the application of PT seed- ing layer offered nucleation sites to PLT thin films, electrical properties of films were enhanced by the increase of crys-tallinity and grain size. The dielectric constant of the films post-heated for 60 min and with a seeding layer was 213 at 1 kHz.

• Journal of Pharmaceutical Investigation
• /
• v.33 no.2
• /
• pp.99-103
• /
• 2003

Four different crystal forms of prednisolone, two polymorphic forms and two pseudopolymorphic forms, were obtained by the recrystallization from different organic solvents under varying conditions. The isolated crystal forms were characterized by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and X-ray powder diffraction (XRD). Form 1 was the most stable form that had the highest melting point and melt at $250.1^{\circ}C$. Form 2 was a monohydrate and Form 3 was a methanol solvate. The endothermic peak of Form 4 was shown at $230.2^{\circ}C$. When stored at different relative humidity over the period of 3 months, all of the modifications did not undergo transformation. The dissolution patterns of these four modifications were also checked in distilled water at $37{\pm}0.5^{\circ}C$, for 120 minutes. The dissolution rate of Form 4 was highest and those of Form 3, Form 2, Form 1 followed. Form 2, Form 3 and Form 4 had higher dissolution rate than Form 1.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.3
• /
• pp.111-114
• /
• 2001

(Ba,Sr) $RuO_3$ thin films were fabricated on Si(100) wafer by metal organic chemical vapor deposition using ultrasonic spraying. When the substrate temperature was varied, the BSR thin films showed good crystallinity above 50$0^{\circ}C$ and showed (110) preferred orientation by X-ray diffraction measurements. The surface morphology, determined by atomic force microscopy, indicated that the grain size of BSR thin films depended strongly on the Ba/Sr ratio. With the increase in the amount of Sr relative to Ba, the resistivity of BSR films decreased fro m415 to 261 $\mu$$\Omega$${\cdot}$cm.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.9
• /
• pp.3255-3260
• /
• 2011

Two novel binuclear metal-organic coordination complexes $[Cd_2(L)_2(bpy)_2(H_2O)_2]{\cdot}6H_2O$ (1), $[Cd_2(L)_2(phen)_2-(H_2O)_2]{\cdot}2H_2O$ (2) (where L = 2-methylquinoline-3,4-dicarboxylate dianion, bpy = 2,2'-bipyridine, phen = 1,10-phenanthroline) have been synthesized under hydrothermal conditions and characterized by single crystal Xray diffraction, spectral method (IR), elemental analysis and thermal gravimetric analysis (TGA). Both 1 and 2 consist of two Cd(II) atoms bridged by two monoatomic bridging carboxylate groups from two L ligands, and the second carboxylate group of each L is monodentately coordinated to Cd(II), creating a sevenmembered chelating ring. The coordination at each metal nucleus is completed by a water molecule and a chelating bidentate molecule. The 3D structures of the complexes are stabilized by ${\pi}-{\pi}$ stacking interactions and hydrogen-bonds.

• Korean Chemical Engineering Research
• /
• v.55 no.3
• /
• pp.279-286
• /
• 2017

This review paper evaluates different kinds of synthesis methods for calcite precipitated calcium carbonates by using different materials. The various processing routes of calcite with different compositions are reported and the possible optimum conditions required to synthesize a desired particle sizes of calcite are predicted. This paper mainly focuses on that the calcite morphology and size of the particles by carbonation process using loop reactors. In this regard, we have investigated various parameters such as $CO_2$ flow rate, Ca $(OH)_2$ concentration, temperature, pH effect, reaction time and loop reactor mechanism with orifice diameter. The research results illustrate the formation of well-defined and pure calcite crystals with controlled crystal growth and particle size, without additives or organic solvents. The crystal growth and particle size can be controlled, and smaller sizes are obtained by decreasing the Ca $(OH)_2$ concentration and increasing the $CO_2$ flow rate at lower temperatures with suitable pH. The crystal structure of obtained calcite was characterized by using X-ray diffraction method and the morphology by scanning electron microscope (SEM). The result of x-ray diffraction recognized that the calcite phase of calcium carbonate was the dominating crystalline structure.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1140-1143
• /
• 2006

We report on the fabrication of P3HT-based thin-film transistors (TFTs) for liquid crystal display that consist of $NiO_x$, poly-vinyl phenol (PVP), and Ni for the source-drain (S/D) electrodes, gate dielectric layer, and gate electrode, respectively The $NiO_x$ S/D electrodes of which the work function is well matched to that of P3HT are deposited on a P3HT channel by electron-beam evaporation of NiO powder. The maximum saturation current of our P3HT-based TFT is about $15{\mu}A$ at a gate bias of -30 V showing a high field effect mobility of $0.079cm^2/Vs$ in the dark, and the on/off current ratio of our TFT is about $10^5$. It is concluded that jointly adopting $NiO_x$ for the S/D electrodes and PVP for gate dielectric realizes a high-quality P3HT-based TFT.