• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.6
• /
• pp.1132-1136
• /
• 1998

The optimum mixing conditions of kochujang(persimmon kochujang) added persimmon puree was optimized by four dimensional response surface methodology. The organoleptic color of persimmon kochujang showed the maximum score in 86.74g red pepper powder, 133.51g persimmon puree and 26.31g salt. The organoleptic aroma persimmon kochujang showed the maximum score in 83.48g red pepper powder, 135.38g persimmon puree and 24.50g salt. The organoleptic taste of persimmon ko chujang showed the maximum score in 85.09g red pepper powder, 133.61g persimmon puree and 25.57g salt. The overall palatability of persimmon kochujang showed the maximum score in 82.99g red pepper powder, 133.10g persimmon puree and 25.47g salt. The optimum mixing conditions for overall orga noleptic properties of persimmon kochujang were 83.00g red pepper powder, 133.00g persimmon puree and 25.00g salt.

• Textile Coloration and Finishing
• /
• v.4 no.3
• /
• pp.122-130
• /
• 1992

To improve the physical properties and the dyeing properties of silk, the silk fabric was treated with urea resin and reactive dyeing. The effects of urea resin concentration, pH of padding bath and curing condition were investigated in order to find optimum condition and the following results are obtained The optimum condition for the crease recovery of silk fabric was urea resin concentration of 80 g/ι, pH of 7, the curings temperature of about 135$^{\circ}C$, and the curing time of 3 minutes. The crease recovery and the thermal insulation ratio of silk fabric were increased by the above treatment. K/S increased as the adding amount of Na$_2$SO$_4$ increased, K/S, however was not affected by the adding amount of Na$_2$CO$_3$. Co1or fastness of the dyed fabrics treated with urea resin were improved slightly compared with untreated ones.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.21 no.2
• /
• pp.31-42
• /
• 2003

The optimum color proofing system with the similar colorants to the printing system has to be used in high quality offset color printing. And so, the evaluation on color reproduction properties of the colorants for proofer and press are very important. In this paper, the optimum color proofing method is recommended by means of colorimeric comparative evaluation on the color reproduction properties such as color gamut, color difference, hue error of the colorants for the proofing system of CRT monitor, inkjet printer, dye sublimation type digital proofer, and the actual printing system of offset press.

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.137-139
• /
• 2006

In order to establish the optimum hot forming temperature and solution heat treatment temperature for 25% chromium super duplex stainless steel weld, a commercial 25%Cr-10%Ni-4%Mo weld metal for super duplex stainless steel(UNS S32750) with different solution heat treatment conditions at $1100^{\circ}C,\;1050^{\circ}C,\;1025^{\circ}C\;and\;1000^{\circ}C$ for 1.5 hours has been investigated by means of optical metallography, and estimated mechanical properties. It is found that exposure to elevated temperatures at $1050^{\circ}C,\;1025^{\circ}C\;and\;1000^{\circ}C$ except $1100^{\circ}C$ brings partial decomposition of ferrite to austenite and sigma phase, which deteriorates their properties and heat treatment at $1100^{\circ}C$ shows acceptable mechanical properties.

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.154-156
• /
• 2005

In the device structure of ITO/tris (8-hydroxyquinoline) aluminum(Alq3)/Al, we investigated the Organic Light-Emitting Diodes (OLEDs) properties as a function of the deposition rate of the $Alq_3$. The deposition rate was from 0.5 to 2.0 $[{\AA}/s]$ in a base pressure of $5{\times}10^{-6}$ [Torr]. It was found that a $Alq_3$ deposition rate of around 1.5 $[{\AA}/s]$ is the optimum for the maximum luminous properties. The optimum deposition rate of $Alq_3$ is 1.5 $[{\AA}/s]$.

• Elastomers and Composites
• /
• v.51 no.4
• /
• pp.280-285
• /
• 2016

The purpose of this study is to get optimum design and operation conditions of the heating rubber roller for laminating process. The cause of performance degradation of heating rubber roller is delamination of rubber on metal tube, rubber aging due to high temperature. We measured the material properties of thermal expansion, thermal conductivity, specific heat and density and analyzed thermal distributions of rubber layer using finite element method. As a result of heat/flow analysis, the density distribution of heating coil must shorten the stabilization time by reducing the temperature deviation on the length direction at the temperature rising section after increasing the density of the area contacting with the laminate film at the center part which is an opposite of the current composition while enabling to maintain the temperature of heater to be consistent while maintaining the temperature deviation to be low when heat loss is created. Finally, we determined optimum heating method of heating rubber roller.

• Journal of Power System Engineering
• /
• v.6 no.4
• /
• pp.49-55
• /
• 2002

In this paper, the elevated temperature tensile properties and short-time creep rupture characteristics were investigated for the friction welded joints of dissimilar materials, Cu-1%Cr-0.5%Zr and STS316L. The joining tests on Cu-1%Cr-0.5%Zr/STS316L by friction welding were performed, and optimum joining conditions of the friction welded joints were determined. The characteristics of the elevated temperature tensile strength, hardness, fractographs were examined, and the creep rupture characteristics for the optimum welded joints were investigated under uniaxal static load at 300, 400 and $500^{\circ}C$.

• Korean Journal of Human Ecology
• /
• v.8 no.4
• /
• pp.5-12
• /
• 2005

The Purpose of this study is to investigate dyeing properties of fabrics with rhubarb colorants. Rhubarb colorants were extracted with water from sliced dry root of rhubarb. Using rhubarb extract, wool fabric specimens were dyed under various conditions(temperature, time, pH, mordants). Effects of dyeing conditions and mordanting on dyeing properties and colorfastness were studied. The color of the dyed fabric specimens were predominantly yellow for all of the pH range. The optimum condition for dyeing with rhubarb extract was dyeing at $80^{\circ}C$ for 30minutes. Al of 4 kinds of mordating agents and pre-mordanting showed the highest chroma value. Washfastness was 3-4, but the dyed wool fabrics became darker on light exposure.

• Journal of the Korean Ceramic Society
• /
• v.38 no.9
• /
• pp.860-865
• /
• 2001

After manufacturing 2mol% CdO substitute $0.05Pb(Mn_{1/3}Sb_{2/3})O_3-0.95Pb(Zr_{0.52}Ti_{0.48})O_3$ piezoelectric ceramics powder as starting material, to manufacture green sheets using Doctor Blade method. The optimum composition of slurry was studied. Moreover, the sintering properties and the dielectric and piezoelectric properties with variation a thickness of the manufactured sheets were investigated. The optimum of slurry was investigated by the rheology with addition of additives, the sintering condition was decided by TGA. And the properties of sheet were investigated through SEM. XRD. The optimum of slurry was the stablest at dispersant 3.0 wt% to solid loading 30vol%. After, at addition of binder/plasticizer(0.75/0.25) 3.0wt%, viscosity was 7.55Pa${\cdot}$s. The dielectric and piezoelectric properties of the sheet were increased a little with the increasing of sintering temperature but were not variable with variation of sheet thickness.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.5
• /
• pp.409-414
• /
• 2012

A theoretical investigation to optimize thermoelectric elements for thermoelectric coolers was performed using a new one-dimensional analytic model. Mathematical expressions for the optimum current and the optimum length of a thermoelectric element, which maximize the coefficient of performance of thermoelectric coolers, were obtained. The optimum current is expressed in terms of the cooling load for a thermoelectric element, the hot and cold side temperatures and thermoelectric properties, but not the length of a thermoelectric element. The optimum current is proportional to the cooling load and decreases as the temperature difference between the hot and cold sides decreases. It is also shown that the optimum length of a thermoelectric element decreases as the cooling load increases.